Page 1 V15.3.00...
Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4: Erp Off Mode Power Consumption Statement
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc- tive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux- embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov- enia.
Page 5 Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has at- tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation.
Page 6: Fcc Statement
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 7: Fcc Rf Radiation Exposure Statement
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Page 8: Important Safety Instructions
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 9: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 10 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 11: Servicing
Preface Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and may expose you and the computer to electric shock. Refer all servicing to authorized service personnel. Unplug the computer from the power supply. Then refer servicing to qualified service personnel under any of the following conditions: •...
Page 12: Power Safety
Preface Power Safety The computer has specific power requirements:  • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety Warning steady, uninterrupted power supply.
Page 13: Polymer Battery Precautions
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha- nism and is not a cause for concern.
Page 14: General Battery Precautions
Preface General Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 15: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 16: Travel Considerations
Preface Travel Considerations As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 17 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 18 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 19: Lcd Screen Care
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 20 Preface XVIII...
Page 21: Table Of Contents
Preface Contents Notice ................................I ErP Off Mode Power Consumption Statement: ................... II FCC Statement ............................IV FCC RF Radiation Exposure Statement: ..................... V Instructions for Care and Operation ......................VII Servicing ..............................IX Power Safety ..............................X Polymer Battery Precautions ........................XI General Battery Precautions ........................XII Cleaning ..............................
Page 22 Preface Model Differences .............................1-6 LCD Panel Open - Model A ........................1-7 LCD Panel Open - Model B ........................1-8 LCD Panel Open - Model C ........................1-9 LED Indicators ............................1-10 Illuminated LED Keyboard ........................1-11 Control Center ............................1-12 Flexikey® Application ..........................1-13 Flexikey® Application Features: ......................1-14 Keyboard Shortcuts ..........................1-15 Function Keys &...
Page 23 Preface Windows 8.1 Taskbar ..........................1-33 Video Features ............................1-34 Microsoft Hybrid Graphics ........................1-34 Power Options ............................1-38 Running Apps ............................1-39 Storage Devices, Mouse, & Audio Overview ..............................2-1 Hard Disk Drive/Solid State Drive ......................2-2 Optical (CD/DVD) Device ........................2-3 Loading Discs ............................2-3 Handling CDs or DVDs ..........................2-4 DVD Regional Codes ..........................2-5 Multi-in-1 Card Reader ..........................2-6 Audio Features ............................2-7...
Page 24 Preface Power Management Overview ..............................3-1 The Power Sources ............................3-2 AC/DC Adapter ............................3-2 Battery ................................3-2 Turning On the Computer ..........................3-3 Shutting the Computer Down ........................3-4 Power Plans ...............................3-5 Power-Saving States ..........................3-7 Sleep ................................3-7 Hibernate ..............................3-8 Shut down ..............................3-8 Configuring the Power Buttons .........................3-9 Resuming Operation ..........................3-11 Power Conservation Modes ........................3-12 Battery Information ..........................3-14...
Page 25 Preface Battery FAQ .............................3-18 Drivers & Utilities What to Install ............................4-1 Module Driver Installation ........................4-1 Driver Installation ............................4-2 Updating/Reinstalling Individual Drivers ....................4-5 User Account Control ..........................4-6 Windows Security Message ........................4-6 New Hardware Found ..........................4-6 Driver Installation Procedure ........................4-7 Chipset ...............................4-7 Video (VGA) .............................4-7 NVIDIA Video (VGA) ..........................4-7 LAN ................................4-7...
Page 26 Preface BIOS Utilities Overview ..............................5-1 The Power-On Self Test (POST) .......................5-2 Failing the POST ............................5-3 Fatal Errors ..............................5-3 Non-Fatal Errors ............................5-3 The Setup Utility ............................5-4 Entering Setup ............................5-4 Setup Screens .............................5-5 Main Menu ..............................5-6 System Time & Date (Main Menu) ......................5-6 SATA Port # (Main Menu) ........................5-7 OffBoard SATA Controller Configuration (Main Menu) .................5-7 ME FW Version/System/Extended Memory (Main Menu) ..............5-7...
Page 27 Preface Set Supervisor Password (Security Menu) ....................5-10 Set User Password (Security Menu) ......................5-11 Password on boot: (Security Menu) ......................5-11 Secure Boot Control (Security Menu) .....................5-12 TPM Configuration (Security Menu) ......................5-13 Boot Menu ...............................5-14 Boot Option Priorities (Boot Menu) ......................5-15 UEFI Boot (Boot Menu) ..........................5-15 Exit Menu ..............................5-16 Modules Overview ..............................6-1...
Page 28 Preface WLAN Configuration in Windows ......................6-14 Fingerprint Reader Module ........................6-17 Fingerprint Reader Driver Installation .....................6-18 Fingerprint Module Configuration ......................6-19 Bluetooth & WLAN Combo Module ......................6-21 3rd Party Bluetooth (V4.0) Combo Driver Installation ................6-22 Intel Bluetooth Combo Driver Installation ....................6-22 Qualcomm Atheros Bluetooth Combo Driver Installation ..............6-23 Bluetooth Configuration in Windows ......................6-24 Intel®...
Page 29 Preface 3G/4G Module ............................6-52 3G/4G Configuration in Windows ......................6-54 Wireless Display ............................6-57 Wireless Display Configuration ......................6-58 Troubleshooting Overview ..............................7-1 Basic Hints and Tips ..........................7-2 Backup and General Maintenance ......................7-3 Viruses ...............................7-4 Upgrading and Adding New Hardware/Software ..................7-5 Problems and Possible Solutions .......................7-7 3G/4G Module PIN Code &...
Page 30 Preface Headphone-Out Jack ..........................A-3 Microphone-In Jack ..........................A-3 RJ-45 LAN Jack ............................A-3 S/PDIF-Out Jack ............................A-3 Security Lock Slot ............................A-3 USB 3.0 Port .............................A-4 Control Center & Flexikey® Overview ..............................B-1 Control Center ............................B-1 Flexikey® ..............................B-1 Power Modes ............................B-3 Control Center Menus ..........................B-4 Power Status (System Program) ......................B-5 Brightness (System Program) ........................B-5 Volume (System Program) ........................B-5...
Page 31 Preface Backlight Keyboard (Device) ........................B-7 TouchPad/PC Camera (Device) .......................B-7 Left Windows Key (Gaming) ........................B-7 Headphone (Gaming) ..........................B-7 Flexikey® (Gaming) ..........................B-7 Caps Lock/Scroll Lock/ Number Lock/Airplane Mode ................B-7 Flexikey® Application ..........................B-8 Language Interface ...........................B-9 Keyboard Settings - Express Key ......................B-13 Enabling Time Record ..........................B-15 Keyboard Settings - Launch App ......................B-17 Keyboard Settings - Express Text ......................B-19 Keyboard Settings - Disable ........................B-21...
Page 32 Preface Video (VGA) ............................C-1 NVIDIA Video (VGA) ..........................C-1 Microsoft Hybrid Graphics ........................C-2 Intel® Dynamic Video Memory Technology ...................C-4 Intel® HD Graphics Control Panel ......................C-5 Display Devices & Options ........................C-19 Attaching Other Displays ........................C-20 Attaching Other Displays - Devices (Charms Bar) ................C-23 Configuring an External Display In Windows ..................C-24 NVIDIA Control Panel ...........................C-26 Customization Options ...........................C-28...
Page 33 Preface Video Adapter Options ..........................D-2 Storage ..............................D-3 BIOS .................................D-3 Audio ................................D-3 Keyboard & Pointing Device ........................D-3 Indicators ..............................D-3 Interface ..............................D-3 Card Reader ..............................D-3 Slots ................................D-3 Communication ............................D-4 Operating System ............................D-4 Features ..............................D-4 Security ..............................D-4 Power Management ..........................D-4 Power ................................D-4 Environmental Spec ..........................D-4 Physical Dimensions &...
Page 34 Preface Start Menu Apps & Tiles .......................... E-4 Windows 10 Control Panel ........................E-6 Settings ..............................E-7 Windows 10 Taskbar ..........................E-8 Video Features ............................E-9 Power Options ............................E-12 Windows 10 Drivers & Utilities ......................E-15 Driver Installation (Windows 10) ......................E-15 Driver Installation Procedure ........................
Page 35 Preface Intel® WLAN Driver Installation ......................E-21 Qualcomm Atheros WLAN Combo Driver Installation ................. E-22 Fingerprint Reader Module ........................E-23 Fingerprint Reader Driver Installation ....................E-23 Fingerprint Module Configuration ......................E-24 Bluetooth & WLAN Combo Module ..................... E-25 3rd Party Bluetooth Combo Driver Installation ..................E-26 Intel Bluetooth Combo Driver Installation .....................
Page 36 Preface XXXIV...
Page 37: Quick Start Guide Overview
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 38: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - 1 “BIOS Utilities” on page 5 - 1 in the User’s Manual.
Page 39: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows 8.1) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals.  Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers.
Page 40: System Software
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 8.1 operating system is sup- ported.
Page 41: System Startup
Quick Start Guide System Startup 1. Remove all packing materials, and place the computer on a stable surface, and securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. 2. When first setting up the computer use the following procedure (as to safeguard the computer during shipping, the battery will be locked to not power the system until first connected to the AC/DC adapter and initially set up as below): •...
Page 42: Model Differences
Quick Start Guide Model Differences This notebook series includes three different model types (with two specification types for Models A & B - see pendix D for full specification details) that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual.
Page 43: Lcd Panel Open - Model A
Quick Start Guide LCD Panel Open - Model A Figure 1 - 2 LCD Panel Open  Model A 1. Built-In PC Camera Wireless Device 2. PC Camera LED Operation Aboard 3. Built-In Microphone Aircraft 4. LCD The use of any portable elec- 5.
Page 44: Lcd Panel Open - Model B
Quick Start Guide LCD Panel Open - Model B Figure 1 - 3 LCD Panel Open Model B  1. Built-In PC Camera Wireless Device 2. PC Camera LED Operation Aboard 3. Built-In Microphone Aircraft 4. LCD The use of any portable elec- 5.
Page 45: Lcd Panel Open - Model C
Quick Start Guide LCD Panel Open - Model C Figure 1 - 4 LCD Panel Open  Model C 1. Built-In PC Camera Wireless Device 2. PC Camera LED Operation Aboard 3. Built-In Microphone Aircraft 4. LCD The use of any portable elec- 5.
Page 46: Led Indicators
Quick Start Guide LED Indicators The LED indicators on the computer display helpful information about the current status of the system. Icon Color Description Icon Color Description Airplane Mode is ON (the WLAN, Bluetooth White Orange The Battery is Charging &...
Page 47: Illuminated Led Keyboard
Quick Start Guide Illuminated LED Keyboard  The white illuminated keyboard has an embedded numerical keypad for easy numer- Other Keyboards ic data input, and features function keys to allow you to change operational features instantly. See Table 1 - 4, on page 1 - 16 for full function key combination details.
Page 48: Control Center
Quick Start Guide Control Center When in the Windows Desktop application (not in the Start screen) press the Fn + Esc key combination, or double-click the icon in the notification area of the taskbar to toggle the Control Center on/off. The Con- trol Center gives quick access to frequently used controls and enables you to quickly turn the camera/Touch Pad on/off (see Appendix B...
Page 49: Flexikey® Application
Quick Start Guide Flexikey® Application The Flexikey® application is a quick hotkey configuration application, which allows you to assign a single key to launch multiple key combinations, or to launch programs and applications, to create text macros and to disable certain keys. The application can also be used to configure the mouse buttons to create hotkeys for gaming etc.
Page 50: Flexikey® Application Features
Quick Start Guide Flexikey® Application Features: For full details see “Flexikey® Application” on page B - • EXPRESS KEY - This feature allows you to configure a single key (or mouse click) to send multiple key combinations, or to create more useful shortcut keys This is useful in gaming or when using applications which have a complex set of keyboard shortcuts.
Page 51: Keyboard Shortcuts
Quick Start Guide Keyboard Shortcuts  The following Windows Logo Key (Winkey) keyboard shortcuts are useful for navi- gation/operation in Windows 8.1. Windows Logo Keyboard Shortcut Windows Logo Use the Windows logo Description Key + + D key com- bination to switch be- Toggle between the Start screen and the foremost running app or the tween the Start screen Tap Winkey...
Page 52: Function Keys & Visual Indicators
Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. Keys Function/Visual Indicators Keys Function/Visual Indicators Fan Control Toggle Fn + Automatic / Full Control Center Toggle (see over) Fn +...
Page 53: Front & Rear Views
Quick Start Guide Front & Rear Views Figure 1 - 8 Front & Rear Views Model A 1. LED Indicators 2. Vent/Fan Intake Model A 3. 1 * USB 3.0 Port 4. HDMI-Out Port 5. Mini Display Port 1.2 6. DC-In Jack Model B Model B Model C...
Page 54: Right View
Quick Start Guide Right View Figure 1 - 9 Right View Model A 1. SIM Card Reader (for 3G/4G USIM Cards - Models A & B Only - see Model B over) 2. Multi-In-1 Card Reader 3. 1 * USB 3.0 Port 4.
Page 55 Quick Start Guide 3G/4G Module USIM Card Installation  (For Model A & B Computers Only) Insert the USIM card as illustrated below (pay careful attention to the orientation USIM Card of the card as the gold contact side of the card should face downwards) until it clicks Orientation fully into position.
Page 56: Left View
Quick Start Guide Left View Figure 1 - 11 Model A Left View Model A 1. Security Lock Slot 2. 2 * USB 3.0 Ports 3. S/PDIF-Out Jack 4. Microphone Jack Model B 5. Headphone Jack 6. Optical Device Drive Bay (for DVD Device) Model C 1 - 20 Left View...
Page 57 Quick Start Guide   Changing DVD Regional Codes Disk Eject Warning Go to the Control Panel and double-click Device Man- Don’t try to eject a CD/DVD while the system is ac- ager (Hardware and Sound), then click the + next to cessing it.
Page 58: Bottom View - Model A
Quick Start Guide Bottom View - Model A Figure 1 - 12 Bottom View  Model A Overheating 1. Fan Outlet/Intake 2. Battery To prevent your comput- from overheating make sure nothing blocks the vent(s)/fan in- take(s) while the com- puter is in use.
Page 59: Bottom View - Model B
Quick Start Guide Bottom View - Model B Figure 1 - 13 Bottom View  Model B Overheating 1. Fan Outlet/Intake 2. Battery To prevent your comput- from overheating make sure nothing blocks the vent(s)/fan in- take(s) while the com- puter is in use.
Page 60: Bottom View - Model C
Quick Start Guide Bottom View - Model C Figure 1 - 14 Bottom View  Model C Overheating 1. Fan Outlet/Intake 2. Battery To prevent your comput- 3. HDD Bay from overheating make sure nothing blocks the vent(s)/fan in- take(s) while the com- puter is in use.
Page 61: Windows 8.1 Control Panel
Quick Start Guide Windows 8.1 Control Panel  Throughout this manual you will see an instruction to open the Control Panel. Windows Versions R ight-click the lower left hot corner to bring up the context menu (or use the Win- + X key combination) and select Control Panel in both the dows Logo Key Note that the informa-...
Page 62 Quick Start Guide The Control Panel can be accessed in a number of ways in Windows 8.1. • Click Search in the Windows Charms Bar (see previous page) and the search pane will pop out. Type Control Panel and select it from the results to the left. •...
Page 63 Quick Start Guide Right-click the Start button in the Desktop app (or use the Windows Logo Key  + X key combination) to bring up an advanced context menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Display Most Search, File Explorer, Command Prompt, Device Manager and Network Connec- Recently Used...
Page 64: Windows 8.1 Start Screen & Desktop
Quick Start Guide Windows 8.1 Start Screen & Desktop The Apps, control panels, utilities and programs within Windows are accessed from the Start screen and/or Windows Desktop app. The Desktop (which runs as an app within the Start screen) can be accessed by clicking the Desktop item in the Start screen (or by using the Windows Logo Key + D key combination).
Page 65: Apps & Tiles
Quick Start Guide Apps & Tiles The Start screen will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on one screen so you will often need use the slider at the bottom of the screen in order to view all the necessary Apps.
Page 66: Desktop Application
Quick Start Guide Desktop Application When the Desktop app is running (click the app in the Start screen or use the Windows Logo Key + D key combination) you can use lower left hot corner to switch between the Start screen and the Windows Desktop app.
Page 67: The Charms Bar
Quick Start Guide The Charms Bar The right side of the screen (Start or Desktop) displays the Charms Bar. The Charms Bar contains the Search, Share, Start, Devices and Settings menus. To access up the Charms Bar move the cursor to the upper or lower right corners of the screen, and then hover over one of the items in the Charms Bar to activate it (the bar will be black when it is active), or use the Windows Logo Key + C key combination.
Page 68 Quick Start Guide Charms Bar Items • Search : You can search for any file, application, Apps and control panel settings with instantaneous results. • Share : This button is used to share information with people via mail or social networks. •...
Page 69: Windows 8.1 Taskbar
Quick Start Guide Windows 8.1 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the task- bar (system tray). In Windows 8.1 the taskbar can be directly accessed from the Desktop application; if you are in the Start screen you will need to move the cursor to the bottom of the screen to display the taskbar.
Page 70: Video Features
Quick Start Guide Video Features Microsoft Hybrid Graphics Microsoft Hybrid Graphics is a seamless technology designed to get best performance from the graphics sys- tem while allowing longer battery life, without having to manually change settings. The computer will automat- ically switch between the integrated UMA (Unified Memory Architecture) GPU (iGPU) and the discrete GPU (dGPU) when required by the applications in use.
Page 71 Quick Start Guide To access Display (Control Panel) and Screen Resolution in Windows: Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Adjust resolution.  Right-Click Desktop 1. You can right-click the desktop and select Screen reso- lution (Figure 1...
Page 72 Quick Start Guide To access the Intel(R) HD Graphics Control Panel: Click Advanced settings (Figure 1 - 24 on page 1 - 35) in the Screen Resolution control panel in Win- dows. Click the Intel(R)... tab and click Graphics Properties (button) (Figure 1 - 25 on page 1 - 36) .
Page 73 Quick Start Guide To access the NVIDIA Control Panel: Right-click the desktop and select NVIDIA Control Panel (Figure 1 - 26). Double-click the icon (Figure 1 - 26) in the Windows control panel. Figure 1 - 26 - NVIDIA Control Panel Video Features 1 - 37...
Page 74: Power Options
Quick Start Guide Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power Menu item in Set- tings in the Charms Bar in Windows 8.1 may be used to Shut down or Restart (you can also add Hibernate/ Sleep to the menu - see “Adding Hibernate/Sleep to the Power Menu”...
Page 75: Running Apps
Quick Start Guide Running Apps To run apps in Windows 8.1 you will need to check that the Screen Resolution and User Account Control Set- tings are compatible with the system requirements. Screen Resolution Settings Switch to the Windows Desktop (click the app or use the Windows logo key + D key combination).
Page 76 Quick Start Guide User Account Control Settings If your computer meets the minimum screen resolution requirements, and still you can't run apps, then that you have to check the status of User Account Control (UAC). Apps may fail to open when the UAC is turned off. To check whether the UAC is on or off, follow the instructions below.
Page 77: Storage Devices, Mouse, & Audio Overview
Storage Devices, Mouse, & Audio Chapter 2: Storage Devices, Mouse, & Audio Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive/Solid State Drive • Optical (CD/DVD) Device • Multi-in-1 Card Reader •...
Page 78: Hard Disk Drive/Solid State Drive
Storage Devices, Mouse, & Audio Hard Disk Drive/Solid State Drive  The hard disk drive (HDD) and/or solid state drive (SSD) is used to store your data Bottom Cover in the computer. The hard disk can be taken out to accommodate other serial (SATA) Removal Warning hard disk drives (see “Storage”...
Page 79: Optical (Cd/Dvd) Device
Storage Devices, Mouse, & Audio Optical (CD/DVD) Device  There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the module you purchased (see “Storage” on page D - 3).
Page 80: Handling Cds Or Dvds
Storage Devices, Mouse, & Audio Handling CDs or DVDs  Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed.
Page 81: Dvd Regional Codes
Storage Devices, Mouse, & Audio DVD Regional Codes To change the DVD regional codes: Go to the Control Panel Double-click Device Manager (Hardware and Sound > Devices and Printers), then click the arrow next to DVD/CD-ROM drives. Double-click on the DVD-ROM device to bring up the Properties dialog box, and select the DVD Region (tab) to bring up the control panel to allow you to adjust the regional code.
Page 82: Multi-In-1 Card Reader
Storage Devices, Mouse, & Audio Multi-in-1 Card Reader  The card reader allows you to use some of the latest digital storage cards. Push the Push-Push Card card into the slot and it will appear as a removable device, and can be accessed in Reader the same way as your hard disk (s).
Page 83: Audio Features
Storage Devices, Mouse, & Audio Audio Features  You can configure the audio options on your computer from the Sound control Volume Adjustment panel in Windows, or from the Realtek HD Audio Manager icon in the notifi- The sound volume level cation area/control panel (right-click the notification area icon to bring up an au- can be set using the vol-...
Page 84: Setup For Audio Recording
Storage Devices, Mouse, & Audio Setup for Audio Recording To record audio sources on your computer at optimum quality follow the instruc- tions below: Click Control Panel and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the notification area icon select Sound Manager).
Page 85: Setup For 5.1 Or 7.1 Surround Sound
Storage Devices, Mouse, & Audio Setup for 5.1 or 7.1 Surround Sound  To setup your system for 5.1 or 7.1 surround sound you will need to connect the au- dio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out Headphone Configuration jacks (note: the S/PDIF jack is used for 7.1 surround sound only).
Page 86 Storage Devices, Mouse, & Audio Plug the front speaker cables into the Headphone-Out Jack. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows: •...
Page 87: Touchpad And Buttons/Mouse
Storage Devices, Mouse, & Audio Touchpad and Buttons/Mouse  The Touchpad is an alternative to the mouse; however, you can also add a mouse to Touchpad Cleaning your computer through one of the USB ports. The Touchpad buttons function in In order to improve pad much the same way as a two-button mouse.
Page 88: Touchpad Sensitivity
Storage Devices, Mouse, & Audio Touchpad Sensitivity  The mouse button zones at the bottom of the pad measure about 15mm from the TouchPad Scrolling bottom of the pad, and the left and right buttons are divided roughly down the mid- dle as illustrated below.
Page 89 Storage Devices, Mouse, & Audio Elan TouchPad  Once you have installed the touchpad driver (see “Touchpad” on page 4 - 8) you Touchpad Disabling can configure the functions by double-clicking the touchpad driver icon in the notification area of the taskbar (or from Options in the ELAN tab in the Mouse If you want to use an exter- control panel in Windows).
Page 90 Storage Devices, Mouse, & Audio The Elan Smart-Pad control panel allows you to use a specific gesture (action) on the surface of the touchpad to perform specific actions to manipulate documents, ob- jects and applications. Click the menu tabs (One-finger, Multi-finger or Additional) and then the function button on the left to access the Configuration controls in the right panel.
Page 91 Storage Devices, Mouse, & Audio Click the Function Description button to get a detailed description of any func- tion. Click the Default button to set any of the functions to the default setting. Figure 2 - 11 Smart-Pad Control Panel with Function Description Touchpad and Buttons/Mouse 2 - 15...
Page 92: One-Finger
Storage Devices, Mouse, & Audio One-Finger Tapping One-Finger tapping is equivalent to clicking the left mouse button to perform a point/click/select function. Figure 2 - 12 Tapping Clicking You can configure actions for two-finger, three-finger and left or right corner clicking actions from the clicking menu.
Page 93 Storage Devices, Mouse, & Audio Drag and Drop You can select the different drag and drop methods from the menu provided. The ob- ject can be released when you lift the finger off the touchpad, when you tap again or after a set time delay.
Page 94 Storage Devices, Mouse, & Audio Edge Swipe Enable Edge Swipe to use a single finger to scroll from the edges of the touchpad to perform the designated function in Windows 8. Figure 2 - 16 Edge Swipe 2 - 18 Touchpad and Buttons/Mouse...
Page 95: Multi-Finger
Storage Devices, Mouse, & Audio Multi-Finger Zooming Place two fingers on the touchpad (for best results use the tips of the fingers) and slide them apart to zoom in, or closer together to zoom out. Figure 2 - 17 Zooming Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically.
Page 96 Storage Devices, Mouse, & Audio Rotation You can rotate objects by using a two-finger gesture. Touch and rotate using two fin- gers on the pad in the direction required. Alternatively place a finger down on the pad and rotate the other finger around it in a circular motion (clockwise or counter- clockwise).
Page 97: Additional
Storage Devices, Mouse, & Audio Additional Palm Tracking This feature helps guard against accidental contact such as palms resting on the pad. Use the slider to adjust the sensitivity of the feature as appropriate. If you are finding that resting your palms on the pad is causing unwanted pointer movement, move the slider towards Maximum (but not so far as to lose all sensitivity).
Page 98 Storage Devices, Mouse, & Audio 2 - 22...
Page 99: Power Management Overview
Power Management Chapter 3: Power Management  OS Note Overview Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.
Page 100: The Power Sources
Power Management The Power Sources  The computer can be powered by either an AC/DC adapter or a battery pack. Forced Off AC/DC Adapter If the system “hangs”, Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ and the Ctrl + Alt + Del key combination doesn’t DC adapter will damage the computer and its components.
Page 101: Turning On The Computer
Power Management Turning On the Computer Now you are ready to begin using your computer. To turn it on simply press the pow- er button on the front panel. When the computer is on, you can use the power button as a Stand by/Hibernate/ Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and holding the power button for longer than this will shut the computer down).
Page 102: Shutting The Computer Down
Power Management Shutting the Computer Down Note that you should always shut your computer down by choosing the Shut down command as this will help prevent hard disk or system problems. Use the Shut down or sign out item in the Context Menu (right-click the lower left corner of the screen to bring up the menu).
Page 103: Power Plans
Power Management Power Plans  The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
Page 104 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow- ered from an AC power source.
Page 105: Power-Saving States
Power Management Power-Saving States  You can use power-saving states to stop the computer’s operation and restart where Wake On LAN you left off. Win 8.1 uses the Sleep, Hibernate and Shut Down power-saving Support states. Wake-On-LAN is only supported from Sleep or Sleep Hibernate states...
Page 106: Hibernate
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost.
Page 107: Configuring The Power Buttons
Power Management Configuring the Power Buttons  The power/sleep button (Fn + F12 key combo) and closed lid may be set to send the Password computer in to a power-saving state. Click Choose what the power buttons do on Protection the left menu in Power Options to bring up the menu.
Page 108 Power Management Adding Hibernate/Sleep to the Power Menu Add Hibernate/Sleep to the Power Menu as follows. Go to the Power Options (Hardware and Sound) control panel 1 - 38 (see page Click “Change settings that are currently unavailable” Click Choose what the power buttons do. Click to put a check in the Hibernate/Sleep box under Shutdown settings.
Page 109: Resuming Operation
Power Management Resuming Operation You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F12 key combo). Power Status Icon Color To Resume Table 3 - 1 Power Off Press the Power Button Resuming Press the Power Button...
Page 110: Power Conservation Modes
Power Management Power Conservation Modes   This system supports Energy Star power management features that place comput- ers (CPU, hard drive, etc.) into a low-power sleep modes after a designated period Power Conservation Power Conservation of inactivity. Adjust Power Conservation Modes from the Control Center: Modes Modes The Energy Star setting...
Page 111 Power Management Ctrl + Alt + Delete Key Combination You can use the CTRL + ALT + DEL key combination from almost any of the Win- dows 8 interfaces/Apps to bring up a full-screen displaying Lock, Switch User, Log off, Change a password and Task Manager options. If you click the Power icon in the lower right corner of the screen a power management option menu appears to display Sleep, Shut down, and Restart.
Page 112: Battery Information
Power Management Battery Information  Follow these simple guidelines to get the best use out of your battery. Low Battery Battery Power Warning Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti- grams you are running, and peripheral devices attached.
Page 113: Conserving Battery Power
Power Management Conserving Battery Power  • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Windows Mobility Center • Lower the brightness level of the LCD display. The system will decrease LCD brightness slightly to save power when it is not powered by the AC/DC adapter.
Page 114: Battery Life
Power Management Battery Life  Battery life may be shortened through improper maintenance. To optimize the life Battery Removal and improve its performance, fully discharge and recharge the battery at least once every 30 days. Note that the built-in battery is not user re- We should not remove the built-in battery yourself (see sidebar).
Page 115: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack  • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode Caution • DO NOT connect the metal terminals (+, -) to each other Danger of explosion if battery is incorrectly re- placed.
Page 116: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Page 117 Power Management Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings. Figure 3 - 13 Change Plan Settings / Change Advanced Power Settings Battery Information 3 - 19...
Page 118 Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 14 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
Page 119 Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to white. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 120 Power Management 3 - 22...
Page 121: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities  This chapter deals with installing the drivers and utilities essential to the operation or Driver Installation & improvement of some of the computer’s subsystems. The system takes advantage of Power some newer hardware components for which the latest versions of most available op- When installing driv- erating systems haven’t built in drivers and utilities.
Page 122: Driver Installation
Drivers & Utilities Driver Installation Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. Click the message “Tap to choose what happens with this disc.” Click Run autorun.exe. Click Install Drivers (button), or Option Drivers (button) to access the Optional driver menu. Figure 4 - 1 - Drivers Installer Screen 1 4 - 2 Driver Installation...
Page 123 Drivers & Utilities Check the driver installation order from Table 4 - 1, on page 4 - 4 (the drivers must be installed in this order) which is the same as that listed in the Drivers Installer menu below. Click to select the driver you wish to install, (you should note down the drivers as you install them). Follow the instructions for each individual driver installation procedure as listed on the following pages.
Page 124 Drivers & Utilities Win 8.1 (64-bit) Page # Win 8.1 (64-bit) - Optional Items Page # Chipset Page 4 - 7 PC Camera Module (no driver installation required) Page 6 - 2 Video (VGA) Page 4 - 7 Wireless LAN Module Page 6 - 11 NVIDIA Video (VGA) Page 4 - 7...
Page 125: Updating/Reinstalling Individual Drivers
Drivers & Utilities Manual Driver Installation Updating/Reinstalling Individual Drivers Click Browse CD/DVD (button) in the Drivers Install- If you wish to update/reinstall individual drivers it er application and browse to the executable file in the may be necessary to uninstall the original driver.To do appropriate driver folder.
Page 126: User Account Control
Drivers & Utilities User Account Control  If a User Account Control prompt appears as part of the driver installation procedure, click Continue or Driver Installation General Guidelines Allow, and follow the installation procedure as direct- The driver installation procedure outlined in this Chapter (and in Chapter 7 Options &...
Page 127: Driver Installation Procedure
Drivers & Utilities Driver Installation Procedure Note: After installing the video driver go to the Dis- play control panel to adjust the video settings to the Insert the Device Drivers & Utilities + User’s Manual highest resolution. disc and click Install Drivers (button). Chipset Note: If the computer enters a deep sleep mode during 1.
Page 128: Touchpad
Drivers & Utilities Touchpad MEI Driver 1. Click 6.Install Touchpad Driver > Yes. 1. Click 9.Install MEI Driver > Yes. 2. Click Next. 2. Click Next. 3. Click the button to accept the license, and then 3. Click the check box to accept the license and click Next.
Page 129 Drivers & Utilities It is recommended that you install the Sound Blaster  Audio application (see “Sound Blaster Cinema 2” on page 6 - 36) and Intel Rapid Storage Technology Windows Update driver (see “Intel® Rapid Storage Technology” on After installing all the drivers make sure you enable Win- page 6 - 27 - required for AHCI &...
Page 130: Optional Drivers
Drivers & Utilities Optional Drivers See the pages indicated in Table 4 - 1, on page 4 - 4 for the driver installation procedures for any modules in- cluded in your purchase option. Models A & B Figure 4 - 3 - Optional Drivers Installer Screen Note that you need to install both the WLAN &...
Page 131: Bios Utilities Overview
BIOS Utilities Chapter 5: BIOS Utilities  BIOS Screens Overview Note that BIOS This chapter gives a brief introduction to the computer’s built-in software: screens pictured these pages are intend- Diagnostics: The POST (Power-On Self Test) ed for guidance in set- ting up your system’s BIOS.
Page 132: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST)  If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you BIOS Settings turn on the computer the system takes a few seconds to conduct a POST, including Warning a quick test of the on-board RAM (memory).
Page 133: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized distributor/supplier as soon as possible.
Page 134: The Setup Utility
BIOS Utilities The Setup Utility  The Aptio Setup Utility tells the system how to configure itself and manage basic BIOS Settings features and subsystems (e.g. port configuration). Warning Entering Setup Incorrect settings can cause your system to To enter Setup, turn on the computer and press F2 (give the system a few seconds malfunction.
Page 135: Setup Screens
BIOS Utilities Setup Screens  The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a Setup Menus new screen appears. Scroll through the features listed on each screen to make chang- Setup menus es to Setup.
Page 136: Main Menu
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings.
Page 137: Sata Port # (Main Menu)
BIOS Utilities SATA Port # (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. OffBoard SATA Controller Configuration (Main Menu) Pressing Enter opens the sub-menu to show the configuration of any devices on the off board SATA Controller if applicable.
Page 138: Advanced Menu
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu Intel(R) Rapid Start Technology (Advanced Menu) Enable/disable Intel(R) Rapid Start Technology from this menu. The rapid start hibernation mode can resume power within seconds and can remember your com- puter's state with zero power. 5 - 8 Advanced Menu...
Page 139: Sata Mode (Advanced Menu)
BIOS Utilities SATA Mode (Advanced Menu) The SATA (Serial ATA) controller operates in AHCI (Advanced Host Controller Interface) mode. Install the Intel Rapid Storage Technology driver to support your drive in AHCI mode (see “Intel® Rapid Storage Technology” on page 6 - 27).
Page 140: Security Menu
BIOS Utilities Security Menu  Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your...
Page 141: Set User Password (Security Menu)
BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then  press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Password Warning Note: You can only set the user password after you have set the supervisor pass- If you set a boot pass- word.
Page 142: Secure Boot Control (Security Menu)
BIOS Utilities Secure Boot Control (Security Menu) Secure Boot Control prevents unauthorized operating systems and software from loading during the startup process. Secure Boot is available as a menu option if you have enabled UEFI Boot (see “Boot Menu” on page 5 - 14).
Page 143: Tpm Configuration (Security Menu)
BIOS Utilities TPM Configuration (Security Menu) This sub-menu will allow you to enable/disable Trusted Platform Module (TPM) support, and to configure the Security Device Support. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable to support TPM (see “Trusted Platform Module”...
Page 144: Boot Menu
BIOS Utilities Boot Menu Figure 5 - 6 Boot Menu  BIOS Screens Note that BIOS screens pictured these pages are intend- ed for guidance in set- ting up your system’s BIOS. BIOS versions are sub- ject to constant change and revision, therefore your computer’s actual When you turn the computer on it will look for an operating system (e.g.
Page 145: Boot Option Priorities (Boot Menu)
BIOS Utilities Boot Option Priorities (Boot Menu) Press Enter to select the Boot Option # and use the arrow keys to select any device in order to move its boot priority up and down the list (the selected device will be highlighted in white).
Page 146: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 7 Exit Menu Click Save Changes and Reset to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will re- turn the Setup to its original state, and erase any previous changes you have made in a previous session.
Page 147: Modules Overview
Modules Chapter 6: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. The chapter includes information on the following: •...
Page 148: Pc Camera Module
Modules PC Camera Module When the PC Camera application is run the LED indicator to the left of the camera will be illuminated in red. Note that you need to use the Camera app in Windows to take pictures and capture video. Use the Fn + F10 key combination (see Table 1 - 4, on page 1 - 16) to toggle power to the PC Camera module.
Page 149: Pc Camera Audio Setup
Modules PC Camera Audio Setup If you want to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Go to the Control Panel. Click Sound (Hardware and Sound) and click Recording (tab). Right-click hold and release Microphone (Realtek High Definition Audio) and make sure the item is not disabled.
Page 150: Camera App
Modules Camera App Run the Camera app from the Start screen by clicking on the Camera app icon The camera interface will display two buttons on the right side of the screen. Figure 6 - 2 Camera App Buttons  Exposure Use the slider to adjust the Exposure level.
Page 151: Camera Options
Modules Camera Options The Camera Options settings may be accessed as follows: Run the Camera app from the Start screen by clicking on the Camera app icon While the camera app is running access the Charms Bar (e.g. click Use the Windows logo key + C key combination).
Page 152: Taking Pictures/Capturing Video
Modules Taking Pictures/Capturing Video Run the Camera app from the Start screen by clicking on the Camera app icon Right-click the screen and select the timer if you require a countdown before capture. Click the appropriate icon to take a picture or start video capture (if video capture begins a timer will appear in the bottom corner of the screen).
Page 153: Camera Roll
Modules Camera Roll Run the Camera app from the Start screen by clicking on the Camera app icon Right-click on the screen to bring up menu buttons at the bottom of the screen. Click Camera Roll. Click the arrows (on either side of the screen) to browse through the captured photos/video, and back to the Camera app.
Page 154 Modules photo with the edited changes), Update original (which changes the original picture permanently) or Undo any changes. Click the Edit button to bring up a full suite of tools to edit the photo. 10. Click on the menu headings on the left, and then click on the tool on the right to edit the photo as required.
Page 155 Modules Editing Videos Clicking on a captured video will bring up an app bar with a series of buttons. Figure 6 - 8 Edit Buttons (for Video) Click Delete to remove any video from the camera roll (you will be asked to click Delete again to confirm the deletion).
Page 156 Modules Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
Page 157: Wireless Lan Module
Modules Wireless LAN Module  If you have included an Intel® or 3rd Party 802.11b/g/n (Combo) module is on Wireless Device (i.e. the system is not in Airplane Mode) before installing the driver. Operation Aboard Aircraft Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - The use of any portable Note that you need to install both the WLAN &...
Page 158: 3Rd Party 802.11B/G/N Driver Installation
Modules 3rd Party 802.11b/g/n Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4.
Page 159: Qualcomm Atheros Wlan Combo Driver Installation
Modules Qualcomm Atheros WLAN Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4.
Page 160: Wlan Configuration In Windows
Modules WLAN Configuration in Windows You can configure a wireless connection using one of the following options, how- ever make sure the Wireless LAN module is turned on (and not in Airplane Mode) before configuration begins. Charms Bar Go to the Charms Bar. Select Settings and then click the WiFi icon (it should read Available under the icon and Airplane mode should be Off).
Page 161 Modules Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next. You can choose to find other devices or not. When you are connected to the network access point it will display Connected Select any connected network and click Disconnect to disconnect from a connected access point.
Page 162 Modules Desktop Mode Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the wireless icon in the notification area of the taskbar. A list of available access points will appear. Double-click an access point to connect to it (or click it and click Connect). Enter a network security key (password) if required, and click Next.
Page 163: Fingerprint Reader Module
Modules Fingerprint Reader Module  The fingerprint reader module provides a high level of security for your computer. Fingerprint Reader Make sure you have administrator’s rights to your computer, and have a Windows and Power Saving password enabled for full security protection. States There are two different fingerprint modules supplied with this model.
Page 164: Fingerprint Reader Driver Installation
Modules Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 2.Install Fingerprint Driver > Yes. 4. Click Next > Install. 5. Click Finish to complete the installation. 6.
Page 165: Fingerprint Module Configuration
Modules Fingerprint Module Configuration Go to the Charms Bar. Select Settings and then click Change PC Settings. Click Accounts and then click Sign-in options. You will need to add a Windows password (click Add under Password). After you have added the password you will need to restart the computer and use your password to log on to the system.
Page 166 Modules 10. Input the Windows password and click OK. 11. You will then be instructed to swipe the same finger across the reader a number of times. Figure 6 - 14 Add a Fingerprint 12. Click Finish. 13. You can choose to Add another finger (this is recommended) or Remove the current fingerprint reading.
Page 167: Bluetooth & Wlan Combo Module
Modules Bluetooth & WLAN Combo Module  If your purchase option includes the Combination Wireless LAN & Bluetooth Wireless Device module (either Intel® or 3rd Party) then install the driver as instructed overleaf. Operation Aboard Aircraft Make sure that the module is on (i.e. the system is not in Airplane Mode) before in- The use of any portable stalling the driver.
Page 168: 3Rd Party Bluetooth (V4.0) Combo Driver Installation
Modules 3rd Party Bluetooth (V4.0) Combo Driver Installation  1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. High Speed Bluetooth Data Transfer 2.
Page 169: Qualcomm Atheros Bluetooth Combo Driver Installation
Modules Qualcomm Atheros Bluetooth Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4.
Page 170: Bluetooth Configuration In Windows
Modules Bluetooth Configuration in Windows  You can configure a Bluetooth connection as below, however make sure the Blue- tooth module is on (or the system is not in Airplane Mode) before configuration. Bluetooth Headset Stereo Setup Desktop Mode Switch to the Windows Desktop (click the App or use the Windows logo key To setup a Bluetooth headset to support ste- D key combination).
Page 171 Modules Make sure that Bluetooth is turned on and a list of discovered devices will appear. Double-click the device you want to pair with the computer and click Pair. Figure 6 - 16 PC and Devices - Bluetooth On first connection the computer will provide you with a pairing code to be entered onto the device.
Page 172 Modules To Make your Computer Discoverable to Bluetooth Devices Switch to the Windows Desktop (click the app or use the Windows logo key D key combination). Click the notification area of the taskbar, click the Bluetooth icon and click Open Settings. Click Options, and make sure that Allow Bluetooth devices to find this computer check box (Discovery) has a check inside it.
Page 173: Intel® Rapid Storage Technology
Modules Intel Rapid Storage Technology ®  Install the Intel® Rapid Storage Technology to support your AHCI mode SATA IRST and M.2 PCI-e drive. SSDs Note that Intel® Rapid IRST Driver Installation Storage Technology 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached does not support M.2 DVD drive.
Page 174: Intel® Rapid Start Technology Driver
Modules Intel Rapid Start Technology Driver ®  Intel(R) Rapid Start Technology can resume power from Hibernation within 7 to Intel® Rapid Start 9 seconds and can remember your computer's previous state with zero power. Technology and M.2 PCI-e SSDs System Requirements to support Intel®...
Page 175: Intel® Rapid Start Technology Configuration
Modules Intel® Rapid Start Technology Configuration Enable/disable Intel(R) Rapid Start Technology from the BIOS (see “Intel(R) Rapid Start Technology (Advanced Menu)” on page 5 - Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management Right-click the SSD and select Shrink Volume from the menu.
Page 176 Modules Enter the figure, which should be equal to amount of system memory (RAM) in your computer, in “Enter the amount of space to shrink in MB”. Figure 6 - 20 Shrink Volume Size Click Shrink (any unallocated file space may be formatted for storage use). ...
Page 177 Modules Run the Desktop app and right-click the lower left hot corner (or use the Windows Logo Key + X key combination) and select Command Prompt (Admin). Figure 6 - 21 Search for CMD Prompt Type “DISKPART”. At the DISKPART command type “list disk”. Figure 6 - 22 Diskpart - List Disk Intel®...
Page 178 Modules Type “select disk #” (# is disk number where you want to create the store partition, so refer to the results obtained from "list disk" for exact disk number). 10. The message “Disk # is now the selected disk.” will appear. Figure 6 - 23 Diskpart - Select Disk #...
Page 179 Modules 13. Type “detail disk”. Figure 6 - 25 Diskpart - Detail Disk 14. Type “select Volume #” (# is volume of your storage partition so refer to results obtained from "detail disk" for the exact volume number). 15. The message “Volume # is now the selected volume.” will appear. Figure 6 - 26 Diskpart - Select Volume #...
Page 180 Modules 16. Type the following, depending on the format of the SSD. • For MBR formatted SSDs: “set id=84 override” (the id must be set to 84). • For GPT formatted SSDs: “set id=D3BFE2DE-3DAF-11DF-BA40-E3A556D89593”. Figure 6 - 27 Diskpart - Set id= 17.
Page 181: Intel® Rapid Start Technology Driver Installation
Modules 19. Go the Windows control panel and double-click Administrative Tools (System and Security)> Computer Management > Storage > Disk Management. 20. The disk partition should read Healthy Hibernation Partition. Figure 6 - 28 Computer Management (Healthy Hibernation Partition) Healthy (Hibernation Partition) 21.
Page 182: Sound Blaster Cinema 2
Modules Sound Blaster Cinema 2 Install the Sound Blaster Cinema 2 application to allow you to configure the audio settings to your requirements for the best performance in games, music and movies. Sound Blaster Cinema 2 Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive.
Page 183: Sound Blaster Cinema 2 Application
Modules Sound Blaster Cinema 2 Application  Run the Sound Blaster Cinema 2 control panel from the notification area of the taskbar (or from the item in the Apps menu). Click on the tabs to access the any of Sound Blaster the control panel menus.
Page 184 Modules Sound Blaster Cinema 2 Tutorial  The Sound Blaster Cinema 2 application will provide a quick Tutorial on the initial run of the application, however you can also run the Tutorial from the drop-down Software Update menu if you require a further introduction to the application. Check for the latest soft- ware updates by making sure you are connected...
Page 185 Modules Sound Blaster Cinema 2 Advanced Settings Sound Blaster Cinema 2 selects the built-in speakers by default and this setting may cause some sound quality issues when using headphones. To adjust the settings for headphones do the following: Run the Sound Blaster Cinema 2 application. Click the Advanced Settings icon Select Headphones from the drop-down menu (you can adjust the slider for crossover frequency and Test to hear the effect chosen).
Page 186 Modules The Sound Blaster Cinema 2 SBX PRO Studio (see overleaf) can be turned On/ Off by clicking the Power Button (when the power is off the icon will be dimmed Volume can be adjusted by means of the slider the right of the volume icon, and you can toggle mute on/off by clicking the volume icon itself ( Power Button...
Page 187: Sound Blaster Cinema 2 Sbx Pro Studio
Modules Sound Blaster Cinema 2 SBX Pro Studio The Sound Blaster Cinema 2 SBX Pro Studio offers a suite of playback technol- ogies to enhance sound. Each playback technology at the bottom of the screen has an On/Off button to allow you to enable/disable it, and most controls feature a slid- er to adjust the levels.
Page 188 Modules • Crystalizer: Enriches audio to make it sound livelier. Figure 6 - 34 Sound Blaster Cinema 2 SBX Pro Studio Crystalizer • Bass: Enhances the bass level of the sound system. Figure 6 - 35 Sound Blaster Cinema 2 SBX Pro Studio Bass 6 - 42 Sound Blaster Cinema 2...
Page 189 Modules • Smart Volume: Minimizes sudden volume changes to avoid the need for con- stant adjustment. Figure 6 - 36 Sound Blaster Cinema 2 SBX Pro Studio Smart Volume • Dialog Plus: Optimizes dialogue levels for movies etc. Figure 6 - 37 Sound Blaster Cinema 2 SBX Pro Studio...
Page 190 Modules Sound Blaster Cinema 2 Profiles The Profile buttons on the left side of the screen give you preset settings to enhance your audio settings for Music, Movie, Game and Voice. You can choose Custom to adjust the settings to your own set preferences. Figure 6 - 38 Sound Blaster Cinema 2...
Page 191 Modules Sound Blaster Cinema 2 & HDMI When you connect an HDMI display to the HDMI-Out port, the Sound Blaster Cin- ema controls will be disabled. A warning box will pop-up and will prompt “...Do you want to select another audio device now?”.
Page 192: Trusted Platform Module
Modules Trusted Platform Module (Optional) The TPM security chip allows you to create and manage digital certificates for user and platform authentication. This type of security is usually administered within large enterprises and organizations, and therefore requires implementation by a sys- tem administrator before users can access security features.
Page 193: Enabling & Managing Tpm
Modules Enabling & Managing TPM Restart the computer. Enter the Aptio Setup Utility pressing F2 during the POST/startup. Use the arrow keys to select the Security menu. Select TPM Configuration and press Enter to access the sub-menu. Press Enter to access the Security Device Support menu and select Enable. Press F4 to save the changes and restart the computer.
Page 194: Tpm Management In Windows
Modules TPM Management in Windows You can manage your TPM settings from within Windows: Go to the Control Panel. Click BitLocker Drive Encryption (System and Security). Click TPM Administration. Figure 6 - 41 BitLocker Drive Encryption (TPM Administration) 6 - 48 Trusted Platform Module...
Page 195 Modules The TPM Management window allows you to configure the TPM within Windows. As TPM is usually administered within large enterprises and organizations, your system administrator will need to assist you in managing the information here. Figure 6 - 42 Trusted Platform Module (TPM) Management on...
Page 196: Tpm Actions
Modules TPM Actions Click Prepare the TPM and follow the instructions in the Wizard to prepare the TPM (this will probably require a restart of the computer and confirmation of the setting changes after restart by pressing the appropriate F key). After the restart the TPM will be prepared and you can then use the Actions menu to Turn TPM off, Change Owner Password, Clear TPM or Reset TPM Lockout.
Page 197 Modules BitLocker BitLocker Drive Encryption can be used in conjunction with the TPM to encrypt data on the disk. Access the Microsoft BitLocker Drive Encryption control panel applet from the Windows control panel (System and Security). Click Turn on Bit Locker. Follow the on-screen instructions to setup BitLocker, and make sure you have a removable media (e.g.
Page 198: 4G Module
Modules 3G/4G Module  (For Model A & B Computers Only) Wireless Device If you have included an optional UMTS/HSPA+ based 3G Module (Universal Mo- Operation Aboard bile Telecommunications System or High Speed Packet Access) module or LTE Aircraft (Long Term Evolution) 4G module (see “Communication”...
Page 199 Modules 3G/4G Module USIM Card Installation  (For Model A & B Computers Only) Insert the USIM card as illustrated below (pay careful attention to the orientation USIM Card of the card as the gold contact side of the card should face downwards) until it clicks Orientation fully into position.
Page 200: 4G Configuration In Windows
Modules 3G/4G Configuration in Windows  You can configure a 3G/4G connection as below, however make sure the system is 3G/4G Module PIN not in Airplane Mode before configuration begins. Code & Power-Saving Charms Bar Note that there may be Go to the Charms Bar.
Page 201 Modules Any 3G service provider (connection information is usually stored on the USIM card) will appear under Mobile Broadband. Double-click any connection icon under Mobile Broadband (or click and then click Connect). Figure 6 - 47 Mobile Broadband (Connect) The system will connect to your network. Connected will appear alongside the connection (click the connection to view the timer which indicates your connected time for the current session).
Page 202 Modules You can then access the internet, download e-mail etc. as per any internet  connection. To disconnect you can select the connection and click Disconnect Wireless Device Operation Aboard Aircraft The use of any portable electronic transmission devices aboard aircraft is usually prohibited.
Page 203: Wireless Display
Modules Wireless Display  Wireless Display (Miracast) uses your Wireless LAN or Wireless LAN & Blue- Compatible tooth Combo module (you need to make sure that your video adapter/display de- Adapters vice is compatible with your particular WLAN/Combo module) in conjunction with a compatible video adapter/display device (purchased separately) to allow you to For a list of compatible display the contents of the notebook display on another display (e.g.
Page 204: Wireless Display Configuration
Modules Wireless Display Configuration Note that no driver or application is required for wireless display in Windows 8.1. Go the Charms Bar, select Devices. Click Project. Click Add a wireless display. Figure 6 - 49 Add a Wireless Display 6 - 58 Wireless Display...
Page 205 Modules The system will then search for compatible display devices (this may take up to 60 seconds so allow time for this to complete). Figure 6 - 50 Searching For Devices Double-click any detected display device in the list. You may then need to input a pin number for the device to which you are connecting.
Page 206 Modules The display will then connect (for specific settings for your display see the documentation supplied with your compatible adapter/display for full details). 10. To disconnect from the display you can select it in PC and Devices > Devices and click Remove Device >...
Page 207: Troubleshooting Overview
Troubleshooting Chapter 7: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 208: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 209: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 210: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 211: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if as this may violate the terms of your warranty.
Page 212 Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem.
Page 213: Problems And Possible Solutions
Troubleshooting Problems and Possible Solutions Problem Possible Cause - Solution You turned on the power but it doesn’t Battery missing / incorrectly installed. Check the battery bay, make sure the work. battery is present and seated properly (the design of the battery only allows it to go in one way).
Page 214 Troubleshooting Problem Possible Cause - Solution The computer feels too hot. Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 215 Troubleshooting Problem Possible Cause - Solution You forget the boot password. If you forget the password, you may have to discharge the battery of the CMOS. Contact your service representative for help.  Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Page 216 Troubleshooting Problem Possible Cause - Solution The system freezes or the screen goes The system’s power saving features have timed-out. Use the AC/DC adapter, dark. press the sleep (Fn + F12) key combination, or press the power button if no LEDs are lit.
Page 217 Troubleshooting Problem Possible Cause - Solution A file cannot be copied to/from a The transfer of data between the computer and a Bluetooth enabled device is connected Bluetooth device. supported in one direction only (simultaneous data transfer is not supported). If you are copying a file from your computer to a Bluetooth enabled device, you will not be able to copy a file from the Bluetooth enabled device to your computer until the file transfer process has been completed I cannot obtain high speed Bluetooth data...
Page 218 Troubleshooting Problem Possible Cause - Solution Audio Volume is too low when listening You have set the Speaker Configuration to 5.1 or 7.1 Speaker. It is through headphones. recommended that you set the Speaker Configuration to Stereo (not to 5.1 or 7.1 Speaker) when listening through headphones in order to maximize audio quality.
Page 219 Troubleshooting Problem Possible Cause - Solution I have used Update Driver in Device It is very important that the drivers are installed in the order indicated in Chapter Manager (Unknown device > Other 4 (which is the numbered installation order on the Device Drivers & Utilities + Devices) to try and install the Airplane User’s Manual disc).
Page 220: 3G/4G Module Pin Code & Power-Saving
Troubleshooting 3G/4G Module PIN Code & Power-Saving (For Model A & B Computers Only) Note that there may be some issues when a PIN Code is set for a 3G/4G module (if you are unsure of your module version contact your distributor/supplier) in Windows, if Mobile Broadband has been turned off, and the system has resumed from a power-saving state.
Page 221 Troubleshooting Click Network. Click the broadband connection under Mobile Broadband. Scroll down to Security and click Remove PIN. Enter the current PIN number and click OK. It is recommended that you do not Enable a PIN for a 3G/4G module. Figure 7 - 2 - Disable PIN 3G/4G Module PIN Code &...
Page 222: Resolving The "Insert A Sim" Issue With The 3G/4G Module (Windows 8.1)
Troubleshooting Resolving the “Insert a SIM” issue with the 3G/4G Module (Windows 8.1) If a PIN was set for the 3G/4G module, you have then switched Mobile broadband off (or put the system in Airplane Mode) in Networks, and the system has just resumed from a power-saving state the following error may occur.
Page 223: Interface (Ports & Jacks) Overview
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to commu- nicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 224: Ports And Jacks
Interface (Ports & Jacks) Ports and Jacks Item Description Card Reader The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC (up to UHS-II) Push the card into the slot and it will appear as a removable device.
Page 225: Hdmi-Out Port
Interface (Ports & Jacks) Item Description HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams. This allows you to connect an external monitor, TV or Flat Panel Display etc. as a display device (see “Attaching Other Displays - Devices (Charms Bar)”...
Page 226: Usb 3.0 Port
Interface (Ports & Jacks) Item Description USB 3.0 Port These USB ports are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power supply which comes with the device).
Page 227: Control Center & Flexikey® Overview
Control Center & Flexikey® Appendix B: Control Center & Flexikey® Overview The following chapter will give a quick description of the functions of the Control Center & Flexikey® appli- cations. Control Center Control Center gives quick access to frequently used controls, power management features and enables you to quickly turn modules on/off.
Page 228 Control Center & Flexikey®  Control Center Access To run the Control Center press the Fn + Esc key combination, or double-click the icon the notification area of the taskbar. Close the Control Center by clicking the close icon in the top right of the panel (move the cursor onto the top right corner of the panel to highlight it).
Page 229 Control Center & Flexikey® Power Modes You can set a Power Mode by clicking the appropriate icon at the top of the Control Center. Each power mode will affect the Power Conservation Mode, Airplane Mode, Power Plan and PC camera power etc. You can click a Control Center icon to set an overall power mode and then click individual icons in the Control Center to power on/off the Touchpad and PC camera.
Page 230 Control Center & Flexikey® Control Center Menus The Control Center contains 3 menu headings (System Program, Device and Gaming) under the Power Modes. Click the menu headings and then click any of the buttons outlined on the following pages. Figure B - 2 - Control Center Menus B - 4 Overview...
Page 231: Power Status (System Program
Control Center & Flexikey® Power Status (System Program) The Power Status icon will show whether you are currently powered by the battery, or by the AC/DC adapter plugged in to a working power outlet. The power status bar will show the current battery charge state. Brightness (System Program) The Brightness icon will show the current screen brightness level.
Page 232: Power Conservation (System Program
Control Center & Flexikey® Power Conservation (System Program) This system supports Energy Star power management features that place computers (CPU, hard drive, etc.) into a low-power sleep modes after a desig- nated period of inactivity (see “Power Conservation Modes” on page 3 - 12).
Page 233: Backlight Keyboard (Device
Control Center & Flexikey® Backlight Keyboard (Device) Click the numbers under the Backlight Keyboard icon to adjust the brightness of the keyboard backlight LED. TouchPad/PC Camera (Device) Click either of these buttons to toggle the TouchPad or camera module’s power status. The icon will appear dimmed when it is off Note that the power status of the camera module is also effected by the Power Mode selected (see...
Page 234: Flexikey® Application
Control Center & Flexikey® Flexikey® Application Click the button in the Control Center, or the click the icon in the notification area of the taskbar, to access the Flexikey® application. Profiles The menus on the left side of the application relate to Profiles. You can Add or Delete Profiles (you can main- tain 12 active Profiles), Export and Import profiles from the menus.
Page 235: Language Interface
Control Center & Flexikey® Flexikey® Application Features • EXPRESS KEY - This feature allows you to configure a single key to send multiple key combinations or to create more useful shortcut keys. This is useful in gaming or when using applications which have a complex set of keyboard shortcuts.
Page 236 Control Center & Flexikey® Enabling or Disabling Flexikey® You can enable or disable Flexikey® (and therefore any hotkeys or mouse profile functions currently in use) by using the Fn + Backspace key combination. Pressing this key combination will toggle you between the currently selected keyboard or mouse profile to the standard keyboard and/or mouse settings, and back again.
Page 237 Control Center & Flexikey® Keyboard Settings The keyboard settings allow you to configure actions for any single key (or a combination of keys). Click the key and then select the Action Type (Express Key, Launch App, Express Text or Disable) from the menu at the bottom of the page.
Page 238 Control Center & Flexikey® Mouse Settings When an external mouse is attached, the mouse settings allow you to configure actions for the left , right and middle buttons of the attached mouse, and also for any backward and forward buttons if appli- cable (on a gaming type mouse).
Page 239: Keyboard Settings - Express Key
Control Center & Flexikey® Keyboard Settings - Express Key To configure a single key to send multiple key combinations, or to create more useful shortcut keys, use Express Key. Enable and select the keyboard under your chosen profile, click on a key to select it, and then click to select Express Key in Action Type.
Page 240 Control Center & Flexikey® Click Save to save the settings within your chosen profile. If you want to remove any individual key click to select it, and then click Delete. If you want to clear all the settings click Restore to return to the default key setting. 10.
Page 241: Enabling Time Record
Control Center & Flexikey® Enabling Time Record If you want to create a delay between key presses within the key combination, then you can use Time Record function to do so. Enable and select the keyboard under your chosen profile, click to select a key for the shortcut action, and then click to select Express Key in Action Type.
Page 242 Control Center & Flexikey® You can edit the delay between key presses by clicking in the Delay Time (MS) field and typing a new number for the delay between the key presses. Figure B - 12 - Time Record Between Key Presses Click to close the Time Record window.
Page 243: Keyboard Settings - Launch App
Control Center & Flexikey® Keyboard Settings - Launch App You can configure keys to launch any application or program as follows: Enable and select the keyboard under your chosen profile, click to select a key to launch the application, and then click to select Launch App in Action Type.
Page 244 Control Center & Flexikey® Navigate to the executable file of the application and click Open. The key will now be configured to open the selected application under your chosen Profile, and the key will appear in green. Figure B - 14 - Key Set to Launch App If you want to remove any Launch App Key, select it and click on Restore.
Page 245: Keyboard Settings - Express Text
Control Center & Flexikey® Keyboard Settings - Express Text A single key can be set to send a string of text within any application using Express Text. Enable and select the keyboard under your chosen profile, click to select a key, and then click to select Express Text in Action Type.
Page 246 Control Center & Flexikey® Click in Send key if required (the Send key is the key used to in your target program to send a text message e.g the Enter key would be the most commonly used), or you can leave it blank if you prefer. The key will now be configured to send the text message in the target program under your chosen Profile, and the key will appear in blue.
Page 247: Keyboard Settings - Disable
Control Center & Flexikey® Keyboard Settings - Disable You can use the program to disable any keys not required. Enable and select the keyboard under your chosen profile, click to select a key to disable, and then click to select Disable in Action Type.
Page 248: Mouse Settings - Express Key
Control Center & Flexikey® Mouse Settings - Express Key To assign a mouse button click to send multiple key combinations (an external mouse must be attached), or to create more useful shortcut keys, use Express Key. Enable and select the mouse under your chosen profile, click on a mouse button to select it, and then click to select Express Key in Action Type.
Page 249: Enabling Time Record For Mouse Settings
Control Center & Flexikey® Click in the Tool Tips field and type to give the key combination a name e.g. “Sprint Fwds”, then click back in the Name field (to avoid adding the recorded keys to the Tool Tips name). Click Start Record and then press the key or keys (in this case we will press Left Shift and W) required (make sure you press the key(s) required and do not click on them).
Page 250: Mouse Settings - Launch App
Control Center & Flexikey® Mouse Settings - Launch App You can assign a mouse button click to launch any application or program as follows: Enable and select the mouse under your chosen profile, click on a mouse button to select it, and then click to select Express Key in Action Type.
Page 251 Control Center & Flexikey® Navigate to the executable file of the application and click Open. The mouse click will now be configured to open the selected application under your chosen Profile, and the button will appear in green Click Save to save the settings within your chosen profile. Figure B - 19 - Mouse Button Set to Launch App Mouse Settings - Launch App B - 25...
Page 252: Mouse Settings - Express Text
Control Center & Flexikey® Mouse Settings - Express Text A mouse button click can be set to send a string of text within any application using Express Text. Enable and select the mouse under your chosen profile, click on a mouse button to select it, and then click to select Express Text in Action Type.
Page 253 Control Center & Flexikey® Click in Send key if required (the Send key is the key used to in your target program to send a text message e.g the Enter key would be the most commonly used), or you can leave it blank if you prefer. The mouse button click will now be configured to send the text message in the target program under your chosen Profile, and the button will appear in blue.
Page 254: Mouse Settings - Disable
Control Center & Flexikey® Mouse Settings - Disable You can use the program to disable any mouse button clicks if not required. Enable and select the mouse under your chosen profile, click on a mouse button to select it, and then click to select Disable in Action Type.
Page 255: Statistics
Control Center & Flexikey® Statistics The Statistics tab allows you to record keys used in any application, and to disable any infrequently, or unused, keys to save any accidental incorrect key presses. Click the Statistics Tab, and press Start Record to start recording the frequency of key presses for keys used. You can then go to the application you wish to use the profile for, and use the application as normal so that a standard set of keys used may be recorded.
Page 256 Control Center & Flexikey® B - 30...
Page 257: Nvidia Video Driver Controls
NVIDIA Video Driver Controls Appendix C: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on  page 1 - 34. Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - Video Card Options Video Driver Installation...
Page 258: Microsoft Hybrid Graphics
NVIDIA Video Driver Controls Microsoft Hybrid Graphics Most notebook computers come with either a discrete or integrated graphics solu- tion. Discrete graphics solutions feature a dedicated Graphics Processing Unit (GPU) which are capable of playing games, watching HD video or running GPU-based ap- plications.
Page 259 NVIDIA Video Driver Controls How the Technology works  When the system is powered up and is displaying just the desktop, the dGPU will be powered off. In this case the system is running in the same way as a system without Customization a discrete graphics solution.
Page 260: Intel® Dynamic Video Memory Technology
NVIDIA Video Driver Controls Intel® Dynamic Video Memory Technology ® Intel DVMT automatically and dynamically allocates as much (up to 1748MB) system memory (RAM) as needed to the integrated video system (the video driver must be installed). DVMT returns whatever memory is no longer needed to the op- erating system.
Page 261: Intel® Hd Graphics Control Panel
NVIDIA Video Driver Controls Intel HD Graphics Control Panel ® Advanced video configuration options are provided by the Intel HD Control Pan- ® el. To access the control panel see below and overleaf: Click the Intel® HD Graphics Control Panel icon in the Apps screen. Figure C - 1 Apps Screen Intel ®...
Page 262 NVIDIA Video Driver Controls Right-click the Desktop and select Graphics Properties from the menu. Click Advanced settings in the Screen Resolution control panel in Windows. Click the Intel(R) HD Graphics Control Panel tab and click Graphics Properties (button). Double-click the Intel(R) HD Graphics control panel in the Windows Control Panel.
Page 263 NVIDIA Video Driver Controls You may make changes to any of the graphics properties by clicking the appropriate menu panel and adjusting the settings from the menus. Figure C - 3 Intel ® HD Graphics Control Panel Intel® HD Graphics Control Panel C - 7...
Page 264 NVIDIA Video Driver Controls Sub-Menus Some of the menu panels will also have sub-menus (in the top left corner of the menu alongside the icon ) to display further configuration options. Figure C - 4 Intel ® HD Graphics Control Panel Sub-Menus C - 8 Intel®...
Page 265 NVIDIA Video Driver Controls Display  Click either Display Settings or Color Settings to make display adjustments, in- cluding configuration for any attached external displays. Multiple Display At least one other dis- play must be attached in order to view multiple display selection tions.
Page 266 NVIDIA Video Driver Controls Click the Display menu at the top of the screen to display the sub-menus. The Mul-  tiple Displays menu allows you to configure the display mode of any attached dis- plays (see “Attaching Other Displays” on page C - 20).
Page 267 NVIDIA Video Driver Controls The Audio sub-menu allows you to configure the capability mode of any attached displays if applicable (i.e. the attached display supports audio). Figure C - 7 Intel ® HD Graphics Control Panel Display - Audio Intel® HD Graphics Control Panel C - 11...
Page 268 NVIDIA Video Driver Controls This menu allows you to choose how 3D images are displayed. Performance dis- plays the smoothest motion of images, Quality displays the most detail, Balanced provides better computer performance with good quality and Custom allows you to configure the Anti-Aliasing, Anisotropic Filtering and Vertical Sync features to your preferences.
Page 269 NVIDIA Video Driver Controls Options and Support Options allows you to Customize Hot Keys (for opening the application, rotating the display, scaling etc.,) to your preferences. Click Apply to save changes. Figure C - 9 Intel ® HD Graphics Control Panel Options &...
Page 270 NVIDIA Video Driver Controls Click the Options and Support menu at the top of the screen to display the sub-  menus. The Information Center provides details on System Information, the Built-In Display and any attached displays. Preferences Go to the Preferences sub-menu in Options and Support to config- ure the preferences for...
Page 271 NVIDIA Video Driver Controls Video The Video Profiles menu allows you to brighten or darken movies, or to switch to vivid colors. The Preview image will display a sample image using the current set- tings. You can Save Profile and name the Profile to recall the settings at any time. Click Apply to save changes (select Color Enhancement, Image Enhancement, Image Scaling or Gamut Mapping from the menu).
Page 272 NVIDIA Video Driver Controls Click the Video menu at the top of the screen to display the sub-menus.The Image Enhancement menu allows you to adjust the Sharpness and Skin Tone Enhance- ment etc. Click Apply to save changes. Figure C - 12 Intel ®...
Page 273 NVIDIA Video Driver Controls The Image Scaling and Gamut Mapping menus allow you to adjust these items. Figure C - 13 Intel ® HD Graphics Control Panel Video Image Scaling & Gamut Mapping Intel® HD Graphics Control Panel C - 17...
Page 274 NVIDIA Video Driver Controls Power Choose a Power Plan for when the computer is Plugged in or On battery. When turned on, the Display Power Saving Technology (which adjusts the backlight in- tensity) battery settings may be adjusted by means of the slider towards Maximum Quality or Maximum Battery.
Page 275: Display Devices & Options
NVIDIA Video Driver Controls Display Devices & Options Note that you can use external displays connected to the HDMI-Out port and/or ex- ternal monitor port and Mini Display (1.2) port. See your display device manual to see which formats are supported. ...
Page 276: Attaching Other Displays
NVIDIA Video Driver Controls Attaching Other Displays  To Clone Displays: Multiple Display Attach your external display to the appropriate port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > At least one other dis- Multiple Displays (sub-menu).
Page 277 NVIDIA Video Driver Controls To Enable Extended Mode:  Attach your external display to the appropriate port, and turn it on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Display Settings Multiple Displays (sub-menu). Extended Desktop Click Extended from the Select Multiple Display Mode menu.
Page 278 NVIDIA Video Driver Controls To Enable Collage Mode:  Attach your external displays to the appropriate ports, and turn them on. Go to the Intel(R) HD Graphics Control Panel control panel and click Display > Collage Mode Multiple Displays (sub-menu). Click Collage from the Select Multiple Display Mode menu.
Page 279: Attaching Other Displays - Devices (Charms Bar
NVIDIA Video Driver Controls Attaching Other Displays - Devices (Charms Bar)  You can configure attached displays from Devices (in the Charms Bar) Windows Logo Key + P Key Attach your external display to the appropriate port, and turn it on. Combination Go the Charms Bar, select Devices.
Page 280: Configuring An External Display In Windows
NVIDIA Video Driver Controls Configuring an External Display In Windows Attach your external display to the external monitor port/HDMI-Out port, and turn it on. Go to the Screen resolution control panel (see page 35) in the Desktop app. Click the Detect button. The computer will then detect any attached displays.
Page 281 NVIDIA Video Driver Controls You can configure the displays from the Multiple Displays menu. Figure C - 20 Screen Resolution Multiple Display Options • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) •...
Page 282: Nvidia Control Panel
NVIDIA Video Driver Controls NVIDIA Control Panel  More advanced video configuration options are provided in the NVIDIA Control NVIDIA Control Panel tab. Panel Go to the Control Panel. To access the Ge- Double-click NVIDIA Control Panel (click to view the control panel in either Large Force..
Page 283 NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and  tools which allow quick access to features such as image settings, 3D Settings and video configuration. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page.
Page 284: Customization Options
NVIDIA Video Driver Controls Customization Options  One of the most important aspects of Hybrid Graphics technology is that it will switch between the integrated GPU and discrete GPU seamlessly and automatically, Display GPU and does not require any input from the user. However customization options are of- Activity Icon fered for users who prefer to set their own parameters for GPU usage.
Page 285 NVIDIA Video Driver Controls Close the NVIDIA Control Panel.  Find the executable file icon of the application you want to run. Right-click the icon and select Run with graphics processor from the context iGPU or dGPU menu. Select either High-performance NVIDIA processor (dGPU) or Integrated Note the NVIDIA con- graphics (iGPU) to run the program with the selected GPU.
Page 286 NVIDIA Video Driver Controls Global Settings Global settings allows you to set the preferred graphics processor for overall use. Ideally this would be the iGPU for battery life, but this can be set to the dGPU if pre- ferred. Go to the NVIDIA Control Panel (see page 26).
Page 287 NVIDIA Video Driver Controls Program Settings Program settings allows you to make specific adjustments for installed applications. Go to the NVIDIA Control Panel (see page 26). Click Manage 3D Settings (3D Settings) and select Program Settings (tab). Select a program to customize from the drop-down menu, or click Add to add any program that does not appear in the menu.
Page 288: Set Physx Configuration
NVIDIA Video Driver Controls Set PhysX Configuration ® NVIDIA PhysX is a physics engine that can use the GPU to accelerate game and ® ® 3D application performance. You can select the GeForce video card or CPU as a PhysX processor, or configure the computer to auto-select a PhysX processor ®...
Page 289: Nvidia Geforce Experience
NVIDIA Video Driver Controls NVIDIA GeForce Experience If you have a working internet connection (and you will need remain connected to the internet to run NVIDIA GeForce Experience) you can click the NVIDIA GeForce Experience desktop icon (or App) to run the application. This will op- timize your gaming settings for your GTX video card by downloading the latest set- tings from the NVIDIA cloud data center.
Page 290 NVIDIA Video Driver Controls NVIDIA GeForce Experience Features • Click the Games tab and click Scan for games to update the optimal settings for your installed games from the NVIDIA cloud data center for your PC. • The Drivers tab allows you to check and download the latest available video driver.
Page 291: Nvidia Geforce Experience - Batteryboost
NVIDIA Video Driver Controls NVIDIA GeForce Experience - BatteryBoost BatteryBoost allows you to optimize your system’s battery life when gaming. You can adjust the BatteryBoost slider in Preferences > BatteryBoost (make sure you have restarted the computer after the first run of NVIDIA GeForce Experience). Running BatteryBoost On first run of NVIDIA GeForce Experience you should be connected to the inter- net (BatteryBoost will not appear at this stage).
Page 292: Nvidia Geforce Experience - Shadowplay
NVIDIA Video Driver Controls NVIDIA GeForce Experience - ShadowPlay Click on the ShadowPlay icon at the top right of the control panel and then click the power button to enable the feature. You can adjust the settings from the menu buttons. Figure C - 31 NVIDIA GeForce Experience...
Page 293: Hdmi Audio Configuration
NVIDIA Video Driver Controls HDMI Audio Configuration  HDMI (High-Definition Multimedia Interface) carries both audio and video signals. Volume Adjustment In some cases it will be necessary to go to the Sound control panel and manually The sound volume level configure the HDMI audio output as per the instructions below.
Page 294 NVIDIA Video Driver Controls Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel. Figure C - 33 HDMI Device Properties C - 38 HDMI Audio Configuration...
Page 295 NVIDIA Video Driver Controls HDMI Notes  • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device. Other Applications • To play audio sources through your external display’s (TV or LCD) speakers If you are using a third you will need to go to the audio configuration control panel on the display and party application to play...
Page 296 NVIDIA Video Driver Controls C - 40...
Page 297: Specifications
Specifications Appendix D: Specifications  Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your distributor/supplier for details.
Page 298: Processor
Specifications Processor Display Intel® HD Graphics 4600 (for i5-4210H / i7-4720HQ Processors) For Models A & B Spec II & Model C Models A & B: Only: 15.6" (39.62cm) FHD (1920 * 1080), 3.2 - Intel® HD Graphics 5200 (for i7- Intel®...
Page 299: Bios
Specifications Storage Keyboard & Pointing Device Card Reader Two Changeable 2.5" 7mm/9.5mm (h) Full Size Isolated White LED Illuminated Embedded Multi-In-1 Push-Push Card Hard Disk Drives (HDD) / Solid State Keyboard with Numeric Pad Reader Drives (SSD) with SATA Interface - MMC / RSMMC Built-In TouchPad (with Multi Gesture &...
Page 300: Communication
Specifications Communication Windows® 10 (64-bit) Environmental Spec Built-In 10/100/1000Mb Base-TX Ethernet Features Temperature ° ° Operating: C - 35 Painted Style (For some Model Designs Non-Operating: -20°C - 60°C 2.0M FHD PC Video Camera Module in this series) Relative Humidity Intel®...
Page 301: Windows 10 Overview
Windows 10 Appendix E: Windows 10 Overview This Appendix contains information (including control panel information, driver installation etc.) for users of the Windows 10 OS. You can refer to the main manual for details of audio & video information, BIOS, modules etc. However drivers information specific to Windows 10 will be included in this Appendix, as well as details on how to navigate the Windows 10 user interface to access the applications, control panels, taskbar etc.
Page 302: Windows 10 Start Menu
Windows 10 Windows 10 Start Menu Most of the apps, control panels, utilities and programs within Windows 10 can be accessed from the Start Menu by clicking the icon in the taskbar in the lower left corner of the screen (or by pressing the Windows Logo Key on the keyboard).
Page 303: Right-Clicking The Windows Logo In Start Menu
Windows 10 Right-Clicking the Windows Logo In Start Menu Right-click the Start Menu icon (or use the Windows Logo Key + X key combination) to bring up an advanced Context Menu of useful features such as Control Panel, Programs and Features, Power Options, Task Manager, Search, File Explorer, Command Prompt, Device Manager and Network Connections etc.
Page 304: Start Menu Apps & Tiles
Windows 10 Start Menu Apps & Tiles The Windows 10 Start Menu will contain a number of apps, and many more will be installed as you add more applications etc. Not all of these apps can fit on the screen so may need click and drag the handles at the edge of the screen to expand the menu in order to view all the apps (you can use the scroll bar to move up and down the screen).
Page 305 Windows 10 Pining/Unpinning Apps & Programs to/from the Start Menu To make things easy to find you can add and remove tiles for apps and programs to the Start Menu. Right-Click on a program’s icon and select Pin to Start from the drop-down menu. To remove an app or program from the Start Menu right-click the icon and select Unpin from Start.
Page 306: Windows 10 Control Panel
Windows 10 Windows 10 Control Panel In many instances throughout this manual you will see an instruction to open the Control Panel. The Control Panel can be accessed in a number of ways in Windows 10. • Right-click the Start Menu icon in the taskbar in the lower left corner of the screen and select Control Panel from the menu.
Page 307: Settings
Windows 10 Settings The Settings item in the Start Menu (and also as an App) gives you quick access to a number of system settings control panels allowing you to adjust settings for System, Devices, Network & internet, Personalization, Ac- counts, Time &...
Page 308: Windows 10 Taskbar
Windows 10 Windows 10 Taskbar In many instances throughout this manual you will see an instruction to access the notification area of the task- bar. The notification area of the taskbar in the bottom right of the screen. Some of the Control Panels and appli- cations referred to throughout the course of this manual can be accessed from here.
Page 309: Video Features
Windows 10 Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearance and Personalization). Click Adjust resolution to make changes to the appearance of the display and to detect and configure any attached displays. In Windows 10 it is possible to quickly configure external displays from the Media Connect menu ( press the Windows logo key on your keyboard and the P key).
Page 310 Windows 10 To access Display (Control Panel) and Screen Resolution in Windows: Go to the Control Panel. Click Display (icon) - In the Appearance and Personalization category. Make and changes required from the Display, Resolution, Orientation or Multiple display menus. Click Apply to save the settings.
Page 311 Windows 10 Display Settings: You can quickly adjust the display by right-clicking the desktop and selecting Display Settings Adjust the settings using the sliders in the menu or click Advanced display settings to change resolution. Click Apply to save any changes made to resolution. Figure E - 10 - Display Settings Video Features E - 11...
Page 312: Power Options
Windows 10 Power Options Power Options (Hardware and Sound) can be accessed from the Control Panel. The Power button item in Start Menu (or the context menu) may be used to Shut down or Restart (you can also add Hibernate/Sleep to the menu - see page 13).
Page 313 Windows 10 You can also use the context menu (right-click the Start Menu icon or press the Windows logo + X key combination) to Sign out, Sleep, Hibernate, Shut down, and Restart.  Adding Hibernate/Sleep to the Power Men Go to the Power Options (Hardware and Sound) control panel.
Page 314 Windows 10 Minimum Screen Resolution Settings Windows 10 has minimum screen resolution requirements. Right-click a blank area of the Desktop and select Screen Resolution (or go to the Display control panel). Adjust the Resolution to make sure that it is at least 1024 * 768, although preferably 1366 * 768 or above. Figure E - 13 - Screen Resolution E - 14 Power Options...
Page 315: Windows 10 Drivers & Utilities
Windows 10 Windows 10 Drivers & Utilities Make sure you install all the drivers and utilities for your Windows 10 system as outlined in the following pages. Driver Installation (Windows 10) Insert the Device Drivers & Utilities + User’s Manual disc into the computer’s DVD drive, or an attached DVD drive if applicable.
Page 316: Chipset
Windows 10 Windows 10 Drivers Chipset Page E - 17 Wireless LAN Module Page E - 20 Video (VGA) Page E - 17 Fingerprint Reader Module Page E - 23 NVIDIA Video (VGA) Page E - 17 Bluetooth & WLAN Combo Module Page E - 25 Page E - 17 Intel®...
Page 317: Video (Vga
Windows 10 Driver Installation Procedure Note: After installing the video driver go to the Dis- play control panel to adjust the video settings to the Insert the Device Drivers & Utilities + User’s Manual highest resolution. disc and click Install Drivers (button). Chipset Note: If the computer enters a deep sleep mode during 1.
Page 318: Touchpad
Windows 10 Touchpad MEI Driver 1. Click 6.Install Touchpad Driver > Yes. 1. Click 9.Install MEI Driver > Yes. 2. Click Next. 2. Click Next. 3. Click the button to accept the license, and then 3. Click the check box to accept the license and click Next.
Page 319: Optional Drivers
Windows 10 Optional Drivers See the following pages for the driver installation procedures for any modules included in your purchase option. Note that you need to install both the WLAN & Bluetooth drivers for the WLAN & Bluetooth Combo modules. Windows 10 Drivers &...
Page 320: E - 20 Wireless Lan Module
Windows 10 Wireless LAN Module If you have included an Intel® or 3rd Party WLAN module in your purchase option make sure that the module is on (i.e. the system is not in Airplane Mode) before installing the driver. Make sure you install the drivers in the order indicated in Table E - 1, on page E - Note that you need to install both the WLAN &...
Page 321: 3Rd Party Wlan Driver Installation
Windows 10 3rd Party WLAN Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4.
Page 322: Qualcomm Atheros Wlan Combo Driver Installation
Windows 10 Qualcomm Atheros WLAN Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install WLAN Driver > Yes. 4.
Page 323: Fingerprint Reader Driver Installation
Windows 10 Fingerprint Reader Module The fingerprint reader module provides a high level of security for your computer. Make sure you have admin- istrator’s rights to your computer, and have a Windows password enabled for full security protection. The fingerprint reader module uses the Sign-in options configuration of the Windows Account. ...
Page 324: Fingerprint Module Configuration
Windows 10 Fingerprint Module Configuration Click the Settings item in the Start Menu and then click Accounts and click Sign-in options. You will need to add a Windows password (click Add under Password). After you have added the password you will need to also add a PIN. Under Windows Hello click Set up under Fingerprint.
Page 325: Bluetooth & Wlan Combo Module
Windows 10 Bluetooth & WLAN Combo Module If your purchase option includes the Combination Wireless LAN & Bluetooth module (either Intel® or 3rd Party) then install the driver as instructed overleaf (two drivers are provided for the 3rd party WLAN module and one for the Intel WLAN module).
Page 326: 3Rd Party Bluetooth Combo Driver Installation
Windows 10 3rd Party Bluetooth Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4.
Page 327: Qualcomm Atheros Bluetooth Combo Driver Installation
Windows 10 Qualcomm Atheros Bluetooth Combo Driver Installation 1. Make sure the system is not in Airplane Mode, and then insert the Device Drivers & Utilities + User’s Manual disc into the DVD drive. 2. Click Option Drivers (button). 3. Click 3.Install Combo BT Driver > Yes. 4.
Page 328: Bluetooth Configuration
Windows 10 Bluetooth Configuration Click the Settings item in the Start Menu and then click Devices. Click Bluetooth and make sure Bluetooth is On and a list of discovered devices will appear. Double-click the device you want to pair with the computer and click Pair. On first connection the computer will provide you with a pairing code to be entered onto the device.
Page 329: Intel® Rapid Storage Technology
Windows 10 Intel Rapid Storage Technology ® Install the Intel® Rapid Storage Technology to support your AHCI mode SATA drive. IRST Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2. Click Option Drivers (button). 3.
Page 330: E - 30 Intel® Rapid Start Technology Driver
Windows 10 Intel Rapid Start Technology Driver ® Intel® Rapid Start Technology Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc an attached DVD drive. 2. Click Option Drivers (button). 3. Click 5.Install Rapid Start Driver > Yes. 4.
Page 331: Sound Blaster Cinema 2
Windows 10 Sound Blaster Cinema 2 Install the Sound Blaster Cinema 2 application to allow you to configure the audio settings to your require- ments for the best performance in games, music and movies. Sound Blaster Cinema 2 Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into an attached DVD drive. 2.
Page 332: Pc Camera
Windows 10 PC Camera Use the Fn + F10 key combination or Control Center button to toggle power to the PC Camera module. When the PC Camera is in use the LED indicator to the left of the camera will be illuminated in red. Note that you need to use the Camera app in Windows to take pictures and capture video.
Page 333: Trusted Platform Module
Windows 10 Trusted Platform Module (Optional) The TPM security chip allows you to create and manage digital certificates for user and platform authentica- tion. This type of security is usually administered within large enterprises and organizations, and therefore re- quires implementation by a system administrator before users can access security features. Make sure you have administrator’s rights to your computer, and have a Windows password enabled for full se- curity protection.
Page 334: E - 34 3G/4G Module
Windows 10 3G/4G Module (For Model A & B Computers Only) If you have included an optional UMTS/HSPA+ based 3G Module (Universal Mobile Telecommunications System or High Speed Packet Access) module or LTE (Long Term Evolution) 4G module (see “Communica- tion”...
Page 335: 3G/4G Configuration In Windows 10
Windows 10 3G/4G Configuration in Windows 10 You can configure a 3G/4G connection as below, however make sure the system is not in Airplane Mode before configuration begins. Click the Settings item in the Start Menu and then click Network and Internet. Click Cellular a list of available access points will appear.
Page 336 Windows 10 E- 36...

Clevo N1X0SD User Manual

Quick Start Guide Overview

Storage Devices, Mouse, & Audio Overview

Power Management Overview

Drivers & Utilities

BIOS Utilities Overview

Modules Overview

Troubleshooting Overview

Interface (Ports & Jacks) Overview

Control Center & Flexikey® Overview

NVIDIA Video Driver Controls

Specifications

Windows 10 Overview

Quick Links

Need help?

Questions and answers

Related Manuals for Clevo N1X0SD

Summary of Contents for Clevo N1X0SD