Advertisement
8. Assemble the front pole assembly inside the X
Tend A-Room
.
TM
9. Grasp the center of the front pole assembly arch,
place it against the roof fabric; and walk towards
the end of the ramp. Place the arch at the front
top stitch line. Wrap the 5 hook/loop belts around
the arch poles to hold place.
10. Keep ball ends of side poles at ramp opening/
hinge and extend the side poles as much as pos-
sible without lifting the X Tend A-Room
ramp. The side poles should be at an angle.
11. Clip the center pole J-support in the center of the
horizontal frame on the rear frame pole assem-
bly. The ball socket must be facing toward room.
See Fig. 5.
12. Assemble the center rafter roof pole and place
the ball end into the socket on the Center pole
support. See Fig. 5.
FIg. 5
Face Ball Socket
Toward Room
Fabric
13. Unlock the lever and pull the center rafter pole
until C-Clip can be snapped onto the center of the
arch of the front pole assembly. Stretch the roof
fabric taut and lock lever.
Note: The center rafter pole will pop out of the ball socket
if too much tension is added.
14. A fabric flap 3" wide with loop tape sewn in, sur-
rounds the door opening of the X-Tend A-Room-
. The hook tape must be placed where it will
TM
stretch the fabric and seal around the door frame.
Place this fabric flap against the walls and ceil-
ing and mark the location. Peel the backing off
the hook tape (approximately 12" at a time), and
press it in place on the walls and ceiling.
Note: To ensure adhesion of the tape to the walls and ceil-
ing, the surfaces must be clean and dry.
15. Locate a place for the ball end bases on the ramp
surface, where they will be out of the way; but al-
low the ramp to close. The "OPEN" cutout should
face the direction of the ramp end to allow for the
pole rotation to different angles.
16. Attach the two ball end bases, one on each side
of the ramp with 2 #8 x 3/4" screws. Snap the front
pole assembly ball ends into the bases. Loosen
the lock and extend each side equally until the
fabric is taut.
off the
TM
Clip The Center
Pole J-Sup-
port In Center
Of Horizontal
Frame Of Rear
Pole
5
X TEND A-ROOM
INSTALLATION AND OPERATION SUPPLEMENT
TM
17. The fabric is held against the ramp with an elastic
cord stretched in a sleeve sewn into the bottom
hem of the fabric assembly. At the ends of the
elastic cord is a rubber coated hook that is to be
attached to the ramp.
If the elastic cord hook is not large enough to fit
on the edge of the ramp, four large rubber coat-
ed J-hooks are provided. Place the J-hook on the
ramp edge and the elastic cord hook is secured
in the J-hook.
18. Pull the front bottom corners taut and mark the lo-
cation where the eyelet grommet makes contact
to the ramp. This is repeated for both sides. Drill
1/8" pilot hole (9/64" in metal) and install a snap
fastener on each side.
19. The corners of the roof fabric has web belts with
buckles. Fasten the web belt to the corners of the
rear/frame pole assembly and stretch the fabric
tight to reduce water pooling.
20. Water Bags/Weights 3105851.004 (available at
your Dometic Dealer) can be added along the
bottom for added bug protection.
E. Operating Tips
1. Privacy panels can be unzipped and rolled up to
allow air circulation.
2. The front panel can be unzipped and rolled up;
however, this will open the end of the room and
the possible danger of someone stepping off the
ramp.
3. Storage pockets are located on both sides of the
X Tend A-Room
Important:
If trailer is equipped with a bed, DO NOT
ROLL BED DOWN if room poles are in place.
for personal items.
TM
Advertisement
