1. Manuals
  2. Brands
  3. Active SmartHome Manuals
  4. Repeater
  5. Repeater
  6. Installation and operation manual

Active SmartHome Repeater Installation And Operation Manual

Active smarthome system
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Enlarged version
REPEATER
REPEATER
REPEATER
REPEATER
I ns t a l l a t i on a nd O pe ra t i o n G ui d e
I ns t a l l a t i on a nd O pe ra t i o n G ui d e
I ns t a l l a t i on a nd O pe ra t i o n G ui d e
I ns t a l l a t i on a nd O pe ra t i o n G ui d e

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Repeater and is the answer not in the manual?

Questions and answers

Summary of Contents for Active SmartHome Repeater

  • Page 1 I ns t a l l a t i on a nd O pe ra t i o n G ui d e I ns t a l l a t i on a nd O pe ra t i o n G ui d e REPEATER REPEATER...

  • Page 2: Table Of Contents

    3.1. Active SmartHome Gateway Learn Procedure 3.2. Repeater Learn Procedure 3.3. Walk Test Mode 3.4. Mounting the Repeater 3.5. Removing the Repeater from the Active SmartHome R e p e a t e r P a g e | 2...
  • Page 3 It is a device that makes your system more powerful by increasing the maximum possible distance between the main unit (Active SmartHome Gateway) and the modules. The Repeater may be used to increase the distance between the R e p e a t e r...
  • Page 4 I ns t a l l a t i on a nd O pe ra t i o n G ui d e I ns t a l l a t i on a nd O pe ra t i o n G ui d e I ns t a l l a t i on a nd O pe ra t i o n G ui d e I ns t a l l a t i on a nd O pe ra t i o n G ui d e Gateway and the following sensors: Gas, Keychain, Keypad, External Siren and...

  • Page 5: Operation Operation

    Flash (1 flash every second): The Repeater is in Walk Test Mode Slow Flash (1 flash every 2 seconds): Slow Flash (1 flash every 2 seconds): The Repeater is in Learning Mode (Device) Slow Flash (1 flash every 2 seconds):...

  • Page 6: Function Switch Block

    03. Transmission: Receive LED (Blue) Transmission: Receive LED (Blue) Transmission: Receive LED (Blue) Transmission: Receive LED (Blue) The Blue LED lights up when the Repeater receives a signal transmission 04. Transmission: Transmit LED (Red) Transmission: Transmit LED (Red) Transmission: Transmit LED (Red) Transmission: Transmit LED (Red) The Red LED lights up when the Repeater transmits a signal.

  • Page 7: Tips For Use

    Tips for Use Tips for Use It is strongly recommended that a distance between each Repeater and/or Active SmartHome Gateway is kept in order to avoid interference and static. If a particular device is within the acceptable range for the Active SmartHome Gateway to receive a transmission signal, the module can be learned by the Active SmartHome Gateway directly by by-passing the Repeater.

  • Page 8: Inst

    (Number 07, see section 3.1). It will emit one beep. For the Active SmartHome Gateway to learn the Repeater, slide DIP Switch 4 to the ON position under Normal Mode. The Repeater will emit a long beep and the yellow LED will light up.

  • Page 9: Repeater Learn Procedure

    3 times and you will then have to repeat the procedure. 4. 4. 4. 4. Move DIP Switch 4 to the OFF position. The Repeater will then emit 1 long beep and the yellow LED will fade as the Repeater returns to Normal Mode.

  • Page 10: Walk Test Mode

    Repeater, it will emit 2 beeps and the blue LED will light up for one second. A maximum of 60 devices can be paired, but if a user attempts to set up more, the Repeater will emit 4 beeps.

  • Page 11: Mounting The Repeater

    3. 3. 3. 3. To exit the Walk Test Mode, slide DIP Switch 2 to OFF, the Repeater will emit 1 long beep and the yellow LED will fade out. Ensure the Repeater is at a maximum distance of 20 m from the Active SmartHome Gateway.

  • Page 12: Removing The Repeater From The Active Smarthome

    I ns t a l l a t i on a nd O pe ra t i o n G ui d e 3 3 3 3 .5 .5 .5 .5..Removing the Repeater from the Removing the Repeater from the Active SmartHome...
  • Page 13 Under Normal Mode, switch DIP Switch 3, the Repeater will emit 1 long beep and the yellow LED will light up. 2. 2. 2. 2. Press and hold the Test Button for 5 seconds. The Repeater will emit 1 long beep to indicate it has been formatted. 3. 3. 3. 3.
  • Page 14 The tamper protection itself is concealed inside Repeater’s body in such a way that when it is affixed by wall-plugs, it is pressed. If the Repeater is lifted, the tamper protection will be activated immediately. To enable this function, switch DIP Switch 8 to ON, to disable it, switch DIP Switch 8 to OFF.
  • Page 15 I ns t a l l a t i on a nd O pe ra t i o n G ui d e I ns t a l l a t i on a nd O pe ra t i o n G ui d e I ns t a l l a t i on a nd O pe ra t i o n G ui d e I ns t a l l a t i on a nd O pe ra t i o n G ui d e R e p e a t e r...

Table of Contents