Table of Contents
Advertisement
Advertisement
Table of Contents
Summary of Contents for Iamm NTD36HD
- Page 2 Federal Communication Commission Statement This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions : This device may not cause harmful interference This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a class B digital device, pursuant to Part 15 of the Federal Communication Commission(FCC) rules.
-
Page 3: Table Of Contents
How to handle and other precautions············································ Name of each point – Top & Front··············································· Name of each point – Rear side·················································· Contents in package······························································· Accessories available at shops·················································· Preparation to use NTD36HD ····································· Procedure··········································································· Kinds of HDD to be installed······················································ HDD Installation···································································· Connecting with PC································································... - Page 4 VIDEO setting change····························································· AUDIO setting change····························································· ETC(Other) settings································································ NETWORK setting································································· WIRELESS (Auto setting)························································ WIRELESS (Manual setting) ···················································· WIRELESS (AD-HOC setting)···················································· LAN Sharing setting(PC) ························································· Network configuration under window 2000······································ IP Address Setup: Ethernet Network using a direct connection·············· MULTIMEDIA FILE PLAYBACK ··································· How to use JUKEBOX CREATOR(BGM ON) ·································...
-
Page 5: Introduction
As NTD36HD supports various music files like MP3, Ogg Vorbis, WMA, M3U and PLS, you can store these files into NTD36HD and enjoy them with easy. And, in case that you make NTD36HD’s own playlist by using ‘JUKE BOX CREATOR’ function, you can enjoy music files(playlisted) as background music(BGM function) with easy and convenient. -
Page 6: Input/Output Functions
Streaming through Wired/Wireless Network Without the procedure to copy files from PC to NTD36HD through USB cable, you can stream various media files in your PC to NTD36HD and playback them back with TV directly through NTD36HD’s Network solution. -
Page 7: Kinds Of Format To Be Supported
• The audio file encoded with copy protection technology is not played back properly. • Even if NTD36HD can playback 2048 x 1352(JPEG), it may not work properly if the JPEG size is over 1920 x 1080. -
Page 8: Tv Out Set-Up And Change
※ If you want to change TV out mode, you can use TV OUT button of remote controller or TV OUT button of the front side of NTD36HD set. ※ LED light of the front side of NTD36HD moves to corresponding position when you press TV OUT button with 2~3sec time interval. -
Page 9: Precautions
Precautions Do not block a ventilation opening Do not drop or give a shock. It may cause serious damage to internal Hard Disk Drive. Keep it away from high temperature, high humidity, nearby magnetic filed and direct Do not touch the plug of the AC power cord sunlight. -
Page 10: How To Handle And Other Precautions
How to handle and other precautions • Make sure that you have to use the AC adapter supplied together with NTD36HD. If not, it may cause unexpected problem like breakdown, fire, etc. • In case that NTD36HD is used or left in a completely covered and high temperature space(like in a car) for long time, it may cause unexpected problem. -
Page 11: Name Of Each Point - Top & Front
Name of each point – Top & Front Button of top side Power(On/Off) Button SETUP Button OK BUTTON PLAY/PAUSE BUTTON STOP Button Direction, REW/FWD and +15/-15sec move Button (▲, ▼, ◀, ▶) Button & LED of front side IR receiver TV OUT Button Video / S-Video or Component(DVD) LED... -
Page 12: Name Of Each Point - Rear Side
Name of each point – Rear Side External IR receiver Connector For Wireless Antenna USB connector for PC S-Video DC FAN Digital Sound DVI Out connector Optical Connector Digital Sound Composite Coaxial Connector Video Connector 2CH Stereo 5.1CH Analog Audio Connector Component Video Connector Wired LAN... -
Page 13: Contents In Package
Contents in package Below items are in the package of NTD36HD □ NTD36HD □ Remote Controller □ AAA size Batteries User’s Manual □ 12V DC Power Adaptor □ Power cord □ A to B USB Cable □ Composite A/V Cable □... -
Page 14: Accessories Available At Shops
Accessories available at shops If below accessories needed, you can buy them at shops by yourself. DVI to RGB Gender DVI to HDMI Gender DVI Single Cable Coaxial Cable Optical Cable S-VIDEO Cable LAN Cable... -
Page 15: Preparation To Use Ntd36Hd
3. Connect AC adapter into NTD36HD, and connect NTD36HD with PC through USB cable 4. Power on NTD36HD(with power button of top side, or with power button of remote controller) 5. In case that the installed HDD is not formatted, please format it first according to normal HDD format procedure 6. -
Page 16: Hdd Installation
2. There is HDD fixture inside. Push it Open up the HDD door slowly. forward(#1) slightly and pull it up(#2). 3. . Insert HDD carefully inside with NTD36HD 4. Fix HDD with HDD fixture like below picture. laid down slightly to minimize impact to HDD. -
Page 17: Connecting With Pc
For Windows ME/ 2000/XP Users 1. Power on your PC system. 2. Connect NTD36HD to your PC with USB Cable. Connect AC adapter to NTD36HD. And power it 3. Wait until your PC recognizes NTD36HD as USB mass storage. 4. Check whether NTD36HD is properly recognized as USB mass storage by clicking and opening “My Computer”... -
Page 18: To Create Folder And To Copy Files
- Note : Primary partition should be over one(1) ※ For HDD partition, refer to Chapter 6. • When you make folder in the HDD of NTD36HD, it is recommended that you make folders like ‘MOVIE’, ‘MUSIC’, ‘PHOTO’. And, you copy files to each folder corresponding to kind of file. -
Page 19: Disconnecting From Pc
Disconnecting from PC When try disconnecting USB cable between NTD36HD and PC, Make sure to follow below procedure. 1. Do double-click the icon of “Safely remove USB……”. 2. Click “Stop” button after selecting “USB Mass Storage Device”.. 3. When the message like picture is shown, disconnect USB cable between NTD36HD and PC. -
Page 20: Connecting To Tv With Composite(Av) Cable
The Composite AV cable is needed to connect with normal TV or Video and is for connecting Composite video signal and 2CH audio signal simultaneously. • Connect yellow cable to the Composite connector of NTD36HD and to the VIDEO connector of TV set. •... -
Page 21: Connecting With Component Cable Or Dvi Connector
When connecting HDTV or other high quality displaying devices, connect like below picture.. Connecting with Component cable Connecting with DVI cable • For safety, connect cables after power off NTD36HD, TV and audio system. • You have to purchase DVI cable and other genders by yourselves from shop... -
Page 22: Connecting With 5.1Ch Audio System
• You need to prepare below cables or gender by yourself as those are not supplied together with NTD36HD. (audio cable for analog 5.1Ch, 3.5 pie gender cable, etc) • Connect with analog 5.1Ch cables like upper picture. -
Page 23: Connecting With Optical Or Coaxial Connector
As the audio output through Optical or Coaxial is digital signal, separate devices like DTS Decoder(or Receiver) is needed additionally. • For safety, connect cables after power off NTD36HD and audio system. • You have to purchase Optical cable or Coaxial cable by yourselves from shop. -
Page 24: Connecting To Network
Connecting to Network To connect NTD36HD to a network, some equipment is required. Ethernet Network using a direct connection to a PC(IP Address setup : 36 page) Connect the NTD36HD to a PC with a crossed cable. ◈ Equipment required. -
Page 25: Remote Controller & Set-Up Menu
Remote Controller & SET-UP Menu To introduce remote controller structure and set-up. Structure of Remote Controller POWER AUDIO OUT SELECT MOVIE FODER HOT KEY TV OUT SELECT JUKEBOX CREATOR MUSIC FOLDER HOT KEY GOTO PHOTO FODER HOT KEY CLEAR ALL(JUKEBOX) BOOKMARK DELETE FILE(JUKEBOX) SLEEP TIMER... -
Page 26: Booting Message & Main Menu
TV Out mode is originally set as PAL/Composite. If no-display on TV screen after booting up, try changing TV Out mode by pressing TV OUT button of remote controller or on the front side of NTD36HD set with 2~3seconds time interval. -
Page 27: Review Of Each Icon On Main Menu
Once activated, those icons can be selected. Otherwise, you can not click or select it. NETWORK icon In case that NTD36HD is connected to network properly through Wired or Wireless LAN, this icon is activated and can be selected. Otherwise, you can not select it. -
Page 28: Setup Menu And How To Set Up
• SETUP Menu is classified like VIDEO, AUDIO, ETC, NETWORK, WIRELESS, EXIT. You can select each item with Left/Right (◀, ▶) button of remote controller or NTD36HD set. • To change setting values, if selecting main item, sub items are listed up. You can select each item with Up/Down(▼, ▲) button. -
Page 29: Video Setting Change
VGA (each Mode ) : In case of connecting with Monitor through DVI to RGB Gender connector. ※ By pressing TV OUT button of remote controller(or NTD36HD unit) several times, you can change TV standard and Video Out mode in order. Standard modes... -
Page 30: Audio Setting Change
5.1CH. Without any separate Decoder or Receiver, you can connect with 5.1CH speaker directly • Sound Effects On : When power off and on NTD36HD, sound effect comes out. Off : No sound effect in power on/off.. • Music Play Mode Single Play : It plays only selected music file. -
Page 31: Etc(Other) Settings
• Use default background : To use original background by canceling the user defined background. • Factory reset : To clear all values set by user and to initialize NTD36HD with values set at factory. • Firmware Update: To select firmware bin file and to update with new firmware. -
Page 32: Network Setting
NETWORK setting The sub option related to network will be displayed by selection of NETWORK icon. • Network Connection : Select either “Wired Net.” (for the Ethernet connection) or “Wireless Net.” depending on the type of network connection you want to set up. •... -
Page 33: Wireless(Auto Setting)
‘Password’ for your AP. In case that you set ESSID as ‘hidden’ or you set ‘password’ with your AP, you need to enter ESSID name or Password by yourself. For entering ESSID name or Password, NTD36HD will show you the specific window. - Page 34 AP) or PC. Then, you may press “RETURN” button to store this setting and exit. Getting IP address The NTD36HD will try to get new IP address from your router. It takes about 30 ~ 60 seconds. With Ad-...
-
Page 35: Wireless (Manual Setting)
ESSID The ESSID of NTD36HD should be exactly same as that of the wireless router or the AP(access point) that you use under network environment. -
Page 36: Wireless (Ad-Hoc Setting)
TKIP WPA NONE WPA2PSK Encryption (WEP) Encryption(WEP) option should be applied case that “WEP” encryption algorithm is used. The encryption setting of NTD36HD should be exactly same as that of the wireless router or the AP(access point) under network environment. - Page 37 Encryption(WPA ,Pre-Shared Key) Encryption(WPA) option should be applied in case that “TKIP” or “AES” encryption algorithm is used. The encryption key of NTD36HD should be exactly same as that of the wireless router or AP(access point) that you use under network environment.