Related Manuals for 3M 770
Summary of Contents for 3M 770
- Page 1 RFID Tracking Pad Model 770 Owners Manual 3M Information and Materials Security 3M Center, Building 225-4N-14 St. Paul, Minnesota 55144-1000 xx-xxxx-xxxx-x Rev 1 Copyright © 2003 3M IPC. All rights reserved.
-
Page 2: Table Of Contents
Section 2 - Installation ................9 Step 1 – Install software on your computer ..................9 Step 2 – Connect the hardware components .................. 9 Mounting the 3M Tracking Pad and RFID Reader..............10 Mounting the Tracking Pad on the wall ..................11... -
Page 3: Table Of Contents
Intended Use Statement The 3M RFID Tracking Pad Model 770 is designed and tested for use with other equipment and software to read and/or program 3M RFID Tags. These tags are used to identify files, folders, and other items such as books. -
Page 4: Safety Messages
HURT or property damage may result if you do not follow these instructions. The safety message is in this box. (Information) icon is used in this manual to draw your attention to other important information. Copyright © 2002 3M IPC. All rights reserved. PRELIMINARY VERSION 1.0... -
Page 5: Safety Messages Contained In This Manual
RFID reader, which, if not avoided, may result in minor or moderate injury: At the end of service life, dispose of the tracking pad and RFID readeraccording to federal, state and local requirements. Copyright © 2002 3M IPC. All rights reserved. PRELIMINARY VERSION 1.0... -
Page 6: Safety Labels
We consider safety labels to be an important part of all devices. Safety labels should be replaced immediately if they become hard to read. If any of the safety labels are missing or cannot be read, please contact 3M Library Systems Technical Service for a replacement label. -
Page 7: Safety Label Locations
Safety Label Locations Copyright © 2002 3M IPC. All rights reserved. PRELIMINARY VERSION 1.0... -
Page 8: Emc, Usa, And Canada Compliance
(2) this device must accept any interference received, including interference that may cause undesired operation. NO MODIFICATIONS. Modifications to this device shall not be made without the written consent of The 3M Company. Unauthorized modifications may void the authority granted under Federal Communications Commission Rules permitting the operation of this device. -
Page 9: Section 1 - Overview
Section 1 - Overview The 3M RFID Tracking Pad Model 770 is used with other equipment and software to read and/or program 3M RFID Tags. These tags are used to identify files, folders, and other items such as books. When used in... -
Page 10: Computer Requirements
50 °F to 104 °F (10 °C to 40 °C) Humidity: 0% to 85% RH, non-condensing Electrical 100 to 120 Vac, ?? A, 50/60 Hz, single phase, approximately??? Watts Copyright © 2002 3M IPC. All rights reserved. PRELIMINARY VERSION 1.0... -
Page 11: Section 2 - Installation
AC Power Requirements 100-240 Vac, 47 to 63 Hz, 0.5 A F_SPG_001 Cabling routing power Cabling recommendations (not affected by 120 Vac cord electrical or lighting) 6.5 ft. (2 meter) Copyright © 2002 3M IPC. All rights reserved. PRELIMINARY VERSION 1.0... -
Page 12: Mounting The 3M Tracking Pad And Rfid Reader
Mounting the 3M Tracking Pad and RFID Reader Tracking Pad Mounting Will clean up these drawings and add wall mounting bracket when designs are finalized. 2 in. (5 cm) minimum distance between tracking pad and metal surface (recommended) Tracking pad can be as close as 1 in. (2.5 cm) to metal surface w/reduced read range) Wall mounting –... -
Page 13: Mounting The Tracking Pad On The Wall
Mounting the Tracking Pad on the wall 770_OM_004 Copyright © 2002 3M IPC. All rights reserved. PRELIMINARY VERSION 1.0...