PMI MB24 Use And Care Manual

MASTER BLASTER
OWNER'S GUIDE

USE AND CARE MANUAL

MODEL MB36, MB24
Congratulations: You have purchased a product of superior
performance and design, which will give the best service
when properly operated and maintained. This cooler is
intended to be used as a convenient roll-around spot
cooler.
This guide was designed to provide you with the information
needed to prepare the unit for roll-around spot-cooling. It
also contains information on how to safely operate, inspect,
maintain and troubleshoot your MasterBlaster evaporative
air cooler.
The first section contains instructions to prepare your
cooler for roll-around portable service. The second section,
Maintenance, contains operational and maintenance
instructions to aid in keeping your unit in good working
order, while Troubleshooting includes information to help
diagnose and repair commonly encountered problems.
Read all instructions carefully before installation
• This cooler must be connected to 120 volt AC, 60 Hz
(cycle) power only. NOTE: Improper voltage will void the
pump and/or motor warranties and may cause serious
personal injury or property damage.
• This cooler must be plugged into a GFCI protected
receptacle, which has been properly installed in
accordance with all local and national codes. If you are not
sure that the receptacle is GFCI protected, consult with a
qualified electrician.
• This cooler is equipped with a power cord having an
equipment grounding conductor and grounding plug. Do
not attempt to defeat this safety device by removing the
grounding pin.
• Do not step on or rollover power cord with heavy or sharp
objects. Do not operate if plug or cord is damaged in any
way. If the unit is damaged or malfunctions, do not
continue to operate it.
• Remove the plug from the electrical receptacle by pulling
on the plug and not the cord.
• Always disconnect electrical power to unit before
attempting to work on or service your cooler.
• Do not operate with evaporative pad removed.
07302013
Safety Trouble Shooting
- - INITIAL RELEASE LRC X/X/2013
PROPRIETARY NOTICE:
ECN REV. DESCRIPTION BY DATE
THIS DOCUMENT AND THE INFORMATION CONTAINED HEREIN ARE PROPRIETARY DATA
Operation Parts Replacement
OF PHOENIX MANUFACTURING INC. NEITHER THIS DOCUMENT OR THE INFORMATION
CONTAINED SHALL BE REPRODUCED, USED OR DISCLOSED TO ANY OTHER WITHOUT
REVISION HISTORY
WRITTEN CONSENT OF PHOENIX MANUFACTURING INC.
Maintenance
READ THIS FIRST!
WARNING -
TO REDUCE THE RISK
OF FIRE, ELECTRIC SHOCK OR INJURY TO
PERSONS, OBSERVE THE FOLLOWING
• Do not operate this cooler (fan motor) with any solid-state
speed control device.
• Do not operate with inlet/outlet grilles removed. Do not
place fingers or any other objects inside the fan section.
Serious risk of personal injury or property damage.
• Never wash your cooler cabinet with a garden hose, water
may harm motor and pump.
NOTE:
• Do not use indoors on carpet or wood floor. Unit may leak
water and could damage flooring or create a slip hazard.
• Do not locate or operate cooler near exhaust or vent pipes
as odors or fumes may be drawn into unit.
• Your warranty does not cover shipping damage. Report all
shipping damage at once to store making the delivery.
• For future reference, record the serial number and
purchase date of your evaporative cooler here:
Serial # ______________________________________________
Purchase Date: _______________________________________
Place of Purchase: ____________________________________
CAUTION: the use of anode devices, chemical additives or
cooler cleaner treatments in this cooler will void the warranty.
PAGE 1
UNLESS OTHERWISE SPECIFIED: Phoenix Manufac
.X = ±.125
.XX = ±.030
.XXX = ±.005 PART DESCRIPTION:
MASTERBLASTER 10K FINA
= ± 2°
MIN. BEND RADIUS =
BLANK NUMBER: DRAWN BY: DATE:
S. KANDOV 11/8/
ALL FLAT PATTERN FEATURES
ARE FORMED UP.
MATERIAL: # OF SHEETS:
ALL DIMENSIONS ARE OUTSIDE AND TO
THE CENTER OF ALL HOLES AND SLOTS. SHEET:
01-999-2439