Philips CE138 User Manual page 2

a
Main unit (with a sleeve)
b
Carrying case (with front panel included)
CE138
c
Trim plate
d
Question?
Disassembly tool X 2
Contact
Philips
e
ISO male connector X 2
f
User manual
3 Install the car audio
system
Caution
‡ Use the controls only as stated in this user manual.
EN User manual
RU
Always follow the instructions in this chapter in sequence.
These instructions are for a typical installation. However, if your
car has different requirements, make the adjustment accordingly.
If you have any question regarding installation kits, consult your
local retailer.
Note
‡
This system is designed for negative ground (earth) 12V DC
operation only.
‡ Always install this system in the car dashboard. Other
locations can be dangerous as the rear of the system heats
up during use.
‡
To avoid short-circuit: before you connect, make sure that
the ignition is off.
‡
Make sure that you connect the yellow and red power
supply leads after all other leads are connected.
‡
Make sure that all loose leads are insulated with electrical
tape.
‡ Make sure that the leads do not get caught under screws
iron parts that will move (e.g. seat rail).
‡
Make sure that all ground (earth) leads are run to a common
ground (earth) point.
‡ Use only the supplied mounting hardware for a safe and
secure installation.
‡
,PSURSHU IXVHV FDQ FDXVH GDPDJH RU ÀUH :KHQ \RX QHHG WR
change the fuse, consult a professional.
‡ :KHQ \RX FRQQHFW RWKHU GHYLFHV WR WKLV V\VWHP PDNH VXUH
that the rating of the car circuit is higher than the total fuse
value of all the connected devices.
‡
Never connect speaker wires to the metal body or chassis
of the car.
‡ Never connect speaker wires with stripes to one another.
Connect wires
All registered and unregistered trademarks are
property of their respective owners.
© 2012 Koninklijke Philips Electronics N.V. Note
All rights reserved.
‡
Make sure that all loose leads are insulated with electrical
&(BB80B9 tape.
‡ Consult a professional to connect wires as instructed below.
EN
1 Check the car's wiring carefully and connect them to the
the supplied ISO male connectors.
1 Safety
Read and understand all instructions before you use this device.
If damage is caused by failure to follow instructions, the warranty
does not apply.
‡
0RGLÀFDWLRQ RI WKH SURGXFW FRXOG UHVXOW LQ KD]DUGRXV
radiation of EMC or other unsafe operation.
‡
The device is designed for negative ground (earth) 12 V DC
operation only.
‡
To ensure safe driving, adjust the volume to a safe and
comfortable level.
‡ ,PSURSHU IXVHV FDQ FDXVH GDPDJH RU ÀUH :KHQ \RX QHHG
to change the fuse, consult a professional.
‡
Use only the supplied mounting hardware for a safe and
secure installation.
ISO male connectors Connect to
‡
To avoid short circuits, do not expose the device to rain or
1 Green strip, black-edged Rear left speaker
water.
green strip
‡
The device shall not be exposed to dripping or splashing.
2 :KLWH VWULS EODFNHGJHG Front left speaker
‡
Do not place any sources of danger on the device (e.g. liquid
white strip
ÀOOHG REMHFWV OLJKWHG FDQGOHV 
‡ 3 Gray strip, black-edged gray Front right speaker
Never insert objects into the ventilation slots or other
strip
openings on the device.
‡
Clean the device with soft, damp cloth. Never use  Purple strip, black-edged Rear right speaker
purple strip
substances such as alcohol, chemicals or household cleaners
on the device.
e Red strip Ignition key +12V DC when
ON/ACC
f Blue strip Motor/electric antenna relay
2 Your car audio system
control lead
g Blue strip, white strip $PSOLÀHU UHOD\ FRQWURO OHDG
Congratulations on your purchase, and welcome to Philips! To fully
h Black strip Ground
EHQHÀW IURP WKH VXSSRUW WKDW 3KLOLSV RIIHUV UHJLVWHU \RXU SURGXFW
i Yellow strip To the +12V car battery
at www.philips.com/welcome.
ZKLFK LV HQHUJL]HG DW DOO WLPHV
Introduction
2 &RQQHFW WKH DQWHQQD DQG DPSOLÀHU DV LOOXVWUDWHG LI
applicable.
With this system, you can:
‡
enjoy audio from a USB storage device, SD/SDHC card,
iPod/iPhone, and external player,
‡
charge your iPod/iPhone, and L
‡ REAR
listen to radio stations.
R
You can enrich sound output with these sound effects:
‡
Dynamic bass boost (DBB)
‡ Digital sound control (DSC)
Playable media:
‡
USB storage device
‡
Compatibility: USB 2.0, USB 1.1
‡ Class support: MSC (Mass Storage Class)
‡
Maximum capacity: 32 G
‡
SD/SDHC card
d c b
‡
Maximum capacity: 32 G
‡
Files
‡ File system: FAT16, FAT32
Sockets on rear panel External sockets or
‡
Maximum number of folders: 99
connectors
‡
0D[LPXP QXPEHU RI WUDFNVÀOHV
1 For ISO male connectors As indicated above
‡ Maximum level of directory: 8
2 REAR L Rear left speaker
‡
PS ÀOHV
6DPSOLQJ IUHTXHQFLHV  N+]  N+]  N+] 3 REAR R Rear right speaker
Bitrates: 8-320 kbps and variable bitrates
 ANTENNA Antenna
‡ ZPD ÀOHV
9HUVLRQV 9 9 9 9 / DQG /
6DPSOLQJ IUHTXHQFLHV  N+]  N+]
%LWUDWHV   NESV DQG YDULDEOH ELWUDWHV Tip
‡ ID3 tag V2.0 or later
‡
The pin arrangement for the ISO connectors depends
‡
8QVXSSRUWHG ÀOHV
on the type of your vehicle. To avoid damage to the unit,
$$& :$9 DQG 3&0 ÀOHV
connect properly.
'50 SURWHFWHG :0$ ÀOHV ZDY PD PS PS DQG DDF
:0$ ÀOHV LQ ORVVOHVV IRUPDW
What's in the box
Mount into the dashboard
Check and identify the contents of the package:
‡
If the car does not have an on-board drive or navigation
computer, disconnect the negative terminal of the car
a b c
battery.
‡ If the car battery is not disconnected, to avoid short-circuit,
make sure that the bare wires do not touch each other.
d e f
1
Make sure that the car dashboard opening is within these
4 Get started
measurements:
)RU WKH ÀUVW WLPH XVH
1
Press
»
[PHILIPS] is displayed and then [SELECT OPERATING
REGION] (select a radio region) scrolls.
2
:KHQ RQH RI WKH IROORZLQJ RSWLRQV LV GLVSOD\HG URWDWH
to select a radio region that matches your location.
‡ [AREA EUROPE] :HVWHUQ (XURSH
‡
[AREA ASIA] $VLD 3DFLÀF
‡
[AREA MID--EAST] (Middle East)
‡
[AREA AUST] (Australia)
‡
[AREA RUSSIA] (Russia)
‡ [AREA USA] (United States)
2
Remove the mounting sleeve with the supplied disassembly
‡
[AREA LATIN] /DWLQ $PHULFD
tools.
‡
[AREA JAPAN] (Japan)
3
Press
»
The system switches to radio mode automatically.
‡ To turn off the system, press and hold
screen backlight is off.
Set the time format
1
Press and hold
2
Press
is displayed.
3
Rotate
‡
[CLK 24H] KRXU WLPH IRUPDW
3
Install the sleeve into the dashboard and bend the tabs
‡
[CLK 12H]: 12-hour time format
RXWZDUG WR À[ WKH VOHHYH
Set the clock
1 Press and hold
2
Press
digits blinking.
3 Rotate
18
3 m
m
4
Rotate
Select a source
Press AS/SOURCE repeatedly to select a source.
‡
[RADIO] /LVWHQ WR )0$0 UDGLR
‡ [MP3--LINK] /LVWHQ WR WKH DXGLR LQSXW WKURXJK WKH MP3-
LINK socket.
4
Slide the unit into the sleeve until you hear a "click". ‡
[iPod/USB] :KHQ D 86% VWRUDJH GHYLFH RU FRPSDWLEOH
L3RGL3KRQH LV FRQQHFWHG DQG UHFRJQL]HG \RX FDQ VHOHFW WKLV
VRXUFH WR SOD\ DXGLR ÀOHV WKDW DUH VWRUHG RQ LW
‡ [SD/SDHC] :KHQ DQ 6'6'+& FDUG LV LQVHUWHG DQG
UHFRJQL]HG \RX FDQ VHOHFW WKLV VRXUFH WR SOD\ DXGLR ÀOHV WKDW
are stored on it.
5 Listen to radio
Select a tuner sensitivity
To search for radio stations with strong signals only or more radio
stations, you can change the tuner sensitivity.
1
Press and hold
2
Press
is displayed.
3
Rotate
‡ [LOC ON]: Search for radio stations with strong signals
5
Attach the trim plate.
only.
‡
[LOC OFF]: Search for radio stations with strong and
weak signals.
Enable the RDS function
Note
‡
The RDS function is enabled by default.
‡ Only when the RDS function is enabled, RDS related
settings can be accessed.
1 Press and hold
2
Press
is displayed.
6
Reconnect the negative terminal of the car battery.
3 Rotate
»
The RDS function is enabled.
Attach the front panel
‡
To disable the RDS function, rotate
[RDS OFF].
1
Insert the notch on the front panel to the chassis on the
main unit.
Search for a radio station
Search for a radio station automatically
Press or
with strong signals.
Search for a radio station manually
1
Press and hold
2 Press the left end of the front panel inwards until it is
2 Press
securely locked with a "click".
displayed.
Store radio stations in memory
a Note
‡
You can store a maximum of six stations in each band.
Store radio stations automatically
1
Press AS/SOURCE repeatedly to switch the source to
[RADIO].
Detach the front panel
2
Press BAND,
3 Press and hold AS/SOURCE until [STORE---] is displayed.
Note
»
$IWHU WKH VHDUFK LV FRPSOHWH WKH ÀUVW VWRUHG UDGLR VWDWLRQ
‡
Before you insert an SD/SDHC card or reset the system,
is broadcast automatically.
detach the front panel.
‡ Before you detach the front panel, make sure that the ‡
To select a stored radio station, press
system is turned off.
1 Press to release the front panel.
Store radio stations manually
2 Pull the front panel outwards to remove it.
1 Press BAND,
2
Tune to the radio station that you want to store.
3
Press and hold
to store the radio station at the selected channel.
6 Play from a storage device
to turn on the system.
WR FRQÀUP
until the
1
Connect a compatible USB storage device or SD/SDHC
to access the system menu. card.
‡
)RU DQ 6'6'+& FDUG GHWDFK WKH IURQW SDQHO ÀUVW
/ repeatedly until [CLK 24H] or [CLK 12H]
insert the card into the card slot, and then attach the
front panel.
to select [CLK 24H] or [CLK 12H].
2 Press AS/SOURCE repeatedly to switch the source to
[iPod/USB] or [SD/SDHC].
‡
:KHQ D 86% VWRUDJH GHYLFH LV FRQQHFWHG DQG
UHFRJQL]HG WKH V\VWHP VZLWFKHV WKH VRXUFH WR [iPod/
USB] automatically.
3
If the play does not start, press .
to access the system menu.
/ repeatedly until [CLK] is displayed with time
Control play
anti-clockwise to set the hour.
Button Function
clockwise to set the minute.
Press repeatedly to select a folder.
/
Pause or resume play.
Press to play the previous or next track.
/
Press and hold to rewind a track or search forward
/
fast.
Press repeatedly to display available information
/DISP
about the current track.
Press repeatedly to select a repeat mode:
‡
[REP ONE]: repeat the current track,
‡ [RPT FLD]: repeat all tracks in the current
folder, or
‡
[RPT ALL]: repeat all tracks in the storage
device.
Press repeatedly to select a play mode:
‡
[SHU ALL]: play all tracks randomly,
‡
[SHU FLD]: play tracks in the current folder
randomly, or
‡ [SHU OFF]: play all tracks in the storage
device in sequence.
to access the system menu.
Switch tracks
/ repeatedly until [LOC ON] or [LOC OFF]
During play, you can switch tracks or folders quickly.
to select a setting.
Switch tracks directly
1
Press to access the track list.
»
7KH ÀOH QDPH RI FXUUHQW WUDFN VFUROOV
2
Rotate to toggle through tracks.
3
Press to play the selected track.
Switch folders for a track
1
Press to access the folder list.
»
The name of current folder scrolls.
to access the system menu. 2
Rotate to toggle through folders.
/ repeatedly until [RDS ON] or [RDS OFF] 3 Press to select the folder.
»
7KH V\VWHP VWDUWV SOD\LQJ WKH ÀUVW WUDFN XQGHU WKH IROGHU
to select [RDS ON].
7 Play from an iPod/iPhone
to select
Note
‡
During play, no audio signals are transferred through the
headphone socket of your iPod/iPhone.
to search for the previous or next radio station
Compatible iPod/iPhone models
This car audio system supports the following iPod and iPhone
models.
‡
or until [M] blinks. L3KRQH 6 L3KRQH  L3KRQH *6 DQG L3KRQH *
‡ L3RG WRXFK QG UG DQG WK JHQHUDWLRQV
or repeatedly until the target frequency is
‡
iPod classic
‡
L3RG QDQR UG WK WK DQG WK JHQHUDWLRQV
Connect your iPod/iPhone
, or repeatedly to select a band.
Connect an Apple 30-pin USB cable to:
‡
the USB socket on the front panel of this system, and
‡ your iPod/iPhone.
»
[iPod/USB] scrolls..
, ,
»
The system starts playing tracks that are stored on your
, , , or .
iPod/iPhone.
Note
, or repeatedly to select a tuner band.
‡ Before you disconnect the iPod/iPhone, switch the system
to another source.
, , , , , or
Radio
Control play
Frequency range - FM    0+]  N+] SHU
VWHS LQ DXWR VHDUFK DQG  N+] SHU
Button Function
step in manual search)
Press repeatedly to select a control mode: control
Usable sensitivity - FM 8 μV
play on your iPod/iPhone, or on the system.
(S/N = 20 dB)
Frequency range
Press to pause or resume play.
 $0 0:    .+] N+]
Press to play the previous or next track. Usable sensitivity - 30 μV
/
$0 0: 61  G%
Press and hold to rewind a track or search forward
/
fast.
Press repeatedly to display available information
/DISP
12 Troubleshooting
about the current track.
Press repeatedly to select a repeat mode:
‡
[REP ONE]: repeat the current track, or
Warning
‡ [REP ALL]: repeat all tracks.
‡ Never remove the casing of this product.
Press repeatedly to select a play mode:
‡ [SHU ALL]: play all tracks randomly,
‡
[SHU ALBM]: play tracks in the current To keep the warranty valid, never try to repair the product
yourself.
album randomly, or
If you encounter problems when using this product, check the
‡ [SHU OFF]: play all tracks in the iPod/iPhone
following points before requesting service. If the problem remains
library in sequence.
XQVROYHG JR WR WKH 3KLOLSV :HE SDJH ZZZSKLOLSVFRPVXSSRUW 
:KHQ \RX FRQWDFW 3KLOLSV PDNH VXUH WKDW WKH SURGXFW LV QHDUE\
and the model number and serial number are available.
Search for a track
No power or no sound
$IWHU DFFHVVLQJ WKH L3RGL3KRQH PHQX \RX FDQ VHOHFW D VSHFLÀF ‡ The power supply from car battery is cut off, or the car
track quickly.
battery runs out of energy. Power the system with car
battery.
1 Press to access the iPod/iPhone menu.
» ‡ Car engine is not on. Turn the car engine on.
[PLAYLIST] scrolls.
‡ Cable is not correctly connected. Check connections.
2
Rotate to select a category.
‡ The fuse is burnt. Replace the fuse.
3 Press to access the list of tracks under the category. ‡ Volume is too low. Adjust volume.
‡ If the above solutions cannot help, press the RESET button.
»
7KH ÀOH QDPH RI WKH ÀUVW WUDFN VFUROOV
‡ Make sure that the current track is in a compatible format.
4 Rotate to select a track.
Noise in broadcasts
»
7KH ÀOH QDPH RI FXUUHQW WUDFN VFUROOV
‡ Signals are too weak. Select other stations with stronger
5 Press to start play.
signals.
‡ Check the connection of the car antenna.
‡ Change the broadcast setting from stereo to mono.
Charge your iPod/iPhone
3UHVHW VWDWLRQV DUH HUDVHG
2QFH WKH L3RGL3KRQH LV GRFNHG DQG UHFRJQL]HG WKH FKDUJLQJ
‡ Battery cable is not correctly connected. Connect the
starts.
battery cable to the terminal that is always live.
Cannot switch the source to iPod/iPhone
8 Listen to an external
‡
Check whether the iPod/iPhone is securely connected.
‡
Check whether the iPod/iPhone is compatible with this
player
system.
‡
Check whether the iPod/iPhone battery is nearly empty.
You can use the system to amplify the audio input from an &RQQHFW LW WR WKLV V\VWHP IRU FKDUJLQJ ÀUVW
external player, for example, MP3 player.
'LVSOD\ VKRZV (55
‡ Data error. Check the USB storage device or SD/SDHC
card.
13 Notice
MP3-LINK
$Q\ FKDQJHV RU PRGLÀFDWLRQV PDGH WR WKLV GHYLFH WKDW DUH QRW
H[SUHVVO\ DSSURYHG E\ 3KLOLSV &RQVXPHU /LIHVW\OH PD\ YRLG WKH
user's authority to operate the equipment.
1
Press AS/SOURCE repeatedly to switch the source to
Compliance
[MP3--LINK].
2 Connect an MP3 link cable to
‡
the MP3-LINK socket on the system, and
‡
the audio output socket (usually the headphone socket)
on the external player.
This product complies with the radio interference requirements of
3 Play the external player.
the European Community.
9 Adjust sound Care of the environment
The following operations are applicable to all supported media.
Button Function
Your product is designed and manufactured with high quality
Rotate to increase or decrease the volume level.
materials and components, which can be recycled and reused.
Press to mute the speakers or release them from
mute status.
Press to enable or disable the maximum volume.
Press and hold to enable or disable the Dynamic
:KHQ WKLV FURVVHGRXW ZKHHOHG ELQ V\PERO LV DWWDFKHG WR D
Bass Boost (DBB) effect.
product it means that the product is covered by the European
3UHVV UHSHDWHGO\ WR VHOHFW D VRXQG HTXDOL]HU
Directive 2002/96/EC. Please inform yourself about the local
separate collection system for electrical and electronic products.
Please act according to your local rules and do not dispose of your
1
Press and hold to activate the setup of
old products with your normal household waste.
FXVWRPL]HG VRXQG HTXDOL]HU
Correct disposal of your old product helps to prevent potential
2 Press repeatedly to select an option: [BAS] negative consequences for the environment and human health.
(bass), [TRE] (treble), [BAL] (balance), or
Environmental information
[FAD] (fader).
$OO XQQHFHVVDU\ SDFNDJLQJ KDV EHHQ RPLWWHG :H KDYH WULHG
3 to make the packaging easy to separate into three materials:
Rotate to adjust the setting.
cardboard (box), polystyrene foam (buffer) and polyethylene
(bags, protective foam sheet.)
Your system consists of materials which can be recycled and
10 Reset the system UHXVHG LI GLVDVVHPEOHG E\ D VSHFLDOL]HG FRPSDQ\ 3OHDVH REVHUYH
the local regulations regarding the disposal of packaging materials,
exhausted batteries and old equipment.
If the system works abnormally, reset the system to factory default
settings.
Trademark notice
:LQGRZV 0HGLD DQG WKH :LQGRZV ORJR DUH WUDGHPDUNV RU
registered trademarks of Microsoft Corporation in the United
States and/or other countries.
1
Detach the front panel.
"Made for iPod" and "Made for iPhone" mean that an electronic
2
Press the RESET button with the tip of a ball-point pen or
DFFHVVRU\ KDV EHHQ GHVLJQHG WR FRQQHFW VSHFLÀFDOO\ WR L3RG RU
toothpick.
L3KRQH UHVSHFWLYHO\ DQG KDV EHHQ FHUWLÀHG E\ WKH GHYHORSHU WR
»
All settings are reset to factory default.
meet Apple performance standards. Apple is not responsible
for the operation of this device or its compliance with safety and
regulatory standards. Please note that the use of this accessory
11 Product Information with iPod or iPhone may affect wireless performance.
iPod and iPhone are trademarks of Apple Inc., registered in the
U.S. and other countries.
Note Other trademarks and trade names are those of their respective
owners.
‡
6SHFLÀFDWLRQV DUH VXEMHFW WR FKDQJH ZLWKRXW SULRU QRWLFH
Copyright
General
2012 © Koninklijke Philips Electronics N.V.
6SHFLÀFDWLRQV DUH VXEMHFW WR FKDQJH ZLWKRXW QRWLFH 7UDGHPDUNV
Power supply 12 V DC (11 V - 16 V), negative
are the property of Koninklijke Philips Electronics N.V or their
ground
respective owners. Philips reserves the right to change products
Fuse  $
at any time without being obliged to adjust earlier supplies
Suitable speaker impedance
accordingly.
  
Maximum power output  : [  FKDQQHOV
Continuous power output
 : [  506  10% T.H.D.)
Pre-Amp output voltage  9
Aux-in level
 P9
RU




‡

‡
 
‡

‡


‡
 
‡

‡

‡


‡

‡
 


 3KLOLSV
3KLOLSV  ZZZSKLOLSV
com/welcome.
‡
86% 6'6'+& L3RGL3KRQH
‡
L3RGL3KRQH
‡

‡ '%%
‡
'6&
‡
86%
‡
86%  86% 
‡
MSC
‡ 
‡
6'6'+&
‡

‡
‡
)$7 )$7
‡
‡

‡

‡ PS
    
³ 
‡
ZPD
   / /
  
³  
‡
,' 
‡
$$& :$9 3&0
:0$ '50 ZDY
PD PS PS DDF
:0$ /RVVOHVV

a b c
d e f
a
b
c
d
³  
e
,62 ³  
f

‡