Error Code List - Pioneer DEH-P700BT XN Service Manual

5

5.2 ERROR CODE LIST

QQ
3 7 63 1515 0
- Error Messages
If a CD is not operative or stopped during operation due to an error, the error mode is turned on and cause(s) of
the error is indicated with a corresponding number. This arrangement is intended at reducing nonsense calls from
the users and also for facilitating trouble analysis and repair work in servicing.
(1) Basic Indication Method
1) When SERRORM is selected for the CSMOD (CD mode area for the system), error codes are written to DMIN
(minutes display area) and DSEC (seconds display area). The same data is written to DMIN and DSEC. DTNO
remains in blank as before.
2) Head unit display examples
Depending on display capability of LCD used, display will vary as shown below. xx contains the error number.
(2) Error Code List
Code Class
10 Electricity
11 Electricity
12 Electricity
TE
L 13942296513
17 Electricity
30 Electricity
44 Electricity
50
Mechanism
A0 System
Remarks: Mechanical errors are not displayed (because a CD is turned off in these errors).
Unreadable TOC does not constitute an error. An intended operation continues in this case.
Upper digits of an error code are subdivided as shown below:
1x: Setup relevant errors, 3x: Search relevant errors, Ax: Other errors.
Bluetooth audio / telephone
Message
ERROR-10
www
ERROR-80
.
5
http://www.xiaoyu163.com
8-digit display
ERROR-xx
Displayed error code Description of the code and potential cause(s)
Carriage Home NG
SERVO LSI Com-
munication Error
Focus Servo NG
Spindle Lock NG
Subcode NG
Setup NG
Search Time Out
ALL Skip
CD On Mech Error
Power Supply NG
Cause Factor
Built-in Bluetooth Unit Initial communication on Bluetooth Unit was failed.
encountered an error •
•
Built-in FLASH ROM Communication on FLASH ROM for phone book was failed.
x ao
y
encountered an error •
i
•
•
http://www.xiaoyu163.com
6
8
6-digit display
ERR-xx
CRG can't be moved to inner diameter.
CRG can't be moved from inner diameter.
-> Failure on home switch or CRG move mechanism.
Communication error between microcomputer and SERVO LSI.
Focusing not available.
-> Stains on rear side of disc or excessive vibrations on REWRITABLE.
Spindle not locked. Sub-code is strange (not readable).
-> Failure on spindle, stains or damages on disc, or excessive vibrations.
A disc not containing CD-R data is found.
Q Q
3 6 7 1 3
Turned over disc are found, though rarely.
CD signal error.
AGC protection doesn't work. Focus can be easily lost.
-> Damages or stains on disc, or excessive vibrations on REWRITABLE.
Failed to reach target address.
-> CRG tracking error or damages on disc.
Skip setting for all track.
(CD-R/RW)
Mechanical error during CD ON.
-> Defective loading motor, mechanical lock and mechanical sensor.
Power (VD) is ground faulted.
-> Failure on SW transistor or power supply (failure on connector).
Abnormality is found in the line that relates to the communication.
(BTPW, BTRST, BTTEST, BTRX, BTTX, BTRTS and BTCTS)
Defect or breakdown of Bluetooth Unit.
u163
Abnormality is found in the line that relates to the communication.
(BTPW, MEMDI, MEMDO and MEMCK).
.
Defect or breakdown of FLASH ROM.
Longevity of FLASH ROM.
DEH-P700BT/XN/UC
6
7
2 9 9 4 2 8
4-digit display
E-xx
1 5 0 5 8 2 9 9 4
m
co
7
8
9 9
A
B
C
2 8 9 9
D
E
F
27
8