Compuprint 9050 Quick Installation And Setup Manual

9050-906 65-9080-9
Quick Ins stallation a
CAUT TION
Hazard dous voltages a
or sock kets of the powe
Carefu ully follow all cl
the ma aterials and solu
High te emperature; sw
least 2 20 minutes for
handlin ng.
If the s second tractor u
gear p rotector cover i
printer or insert any ob
This p printer has an
printer is installed on
stand or surface mu
21kg (4 46lb) and with s
Unpa cking Your Printer
The foll lowing items
are incl uded in the
carton:
- Ribbo on Cartridge
- Powe r Cord
- CD fo r drivers and
User's s Guides
- Quick Setup Guide
Contac t your point of p purchase seller
Attentio on! Always retai n the original pr
shipme ent of the printer r.
Unpa cking the pr rinter
Locat ting Printer Parts
Front t View
Choo sing a suita able location
Conside er the follow wing points
when y you choose the location for
your pr inter:
-The di stance between n the printer
and the e host compute er must not
exceed the length of th he interface
cable.
-The lo ocation must be sturdy,
horizon ntal and stable.
-Your printer must t not
expose d to direct t sunlight,
extreme e heat, cold , dust
humidit ty (see "Printer
MAN1 10xxxR01
300-9300e e
plus
and Setup p Guide
are present. Do not touch the p
er receptacle.
eaning instruc tions, using o
utions recomme nded.
witch off the pr inter and allow
parts in this ar rea to cool befo
unit is not install ed, make sure
s closed. Do no ot touch Inside
bject into the ge ears.
optional printe r pedestal. If
any other stan nd or surface, t
st support the printer weight
stand the print a action vibration.
if any items are missing.
rinter packaging g in case of any
R Rear View
n
s stacked on the e floor or on
s surface below the base of t
printer. For s p successful form
parking, the in p nput forms sta
m must always b e lower than t
b base of the prin ter.
A Area outside the e printer:
W Width: 20cm (7 7.9in.) each side
D Depth:100cm 3 39.4in.) each sid
Height:80cm (3 H 31.5in.)
be
or
Sp pecifications"
Gu uide you find o
– You need a
co ompatible with
pr rinter's power co
-F For best continuo
sta acking, the form
pins
only
N ominal AC i
Nominal Voltage N
w at
fore
100–240Vac
Removing th R
the
1. Open the tracto
the
shipping locks.
2. Open the upper
the
head, remove it
this
t of
In nstalling the
We recommend t W
ins stall the ribbon c
1. Remove the rib
guide, snap ar
pins.
2.T Turn the ribbon
any slack in th
place of ribbon
3. Open the top co
cover.
4. Slide the print h
5.A Align the cartrid
right cartridge s
6. Position the ribb
perpendicular to
7.T Turn the ribbon
8. Position the sn
assembly. Pus
until it snaps int
9.A Align the ribbon
cartridge with t
cartridge down
10 0.Turn the ribbo
take up any sla
and forth to en
ribbon.
11 1.If the ribbon
installed the rib
a.The left and r
into the cartridg
b.There are not
c.The ribbon is
d.The ribbon m
the direction
the ribbon ca
purchase if yo
12 2.Close the top
a
the
ms
ack
the
e
de
1
in the User r's
on the CD-Rom m).
a power outle et
the plug of th he
ord.
ous forms
ms should be
input power r requiremen
e Voltage R Range Amp
90–264 4Vac 3.8
e Shipment Locks
or area cover an nd make sure th
Store the lock s swith the packin
r printer cover. I If there is a wire
t.
Ribbon Ca rtridge
that you use an n approved origi
cartridge, follow w these steps:
bon cartridge fro rom the package
rm, ribbon adva ance knob, an
advance knob in the direction
e ribbon. If the e ribbon does n
purchase to rep place the ribbon
over using the s small handles o
head to the cent ter of the printer
dge pins with the e locking groove
supports.
bon guide over t the print head,
o the print head d.
advance knob to take up any s
nap arm with th he small lever
h the snap arm m down onto th
to place.
n mounting pins on the left and
the slots in the e cartridge supp
into place.
n advance knob b again in the di
ack in the ribbo on, as you slide
nsure that the rib bbon guide runs
is not running g freely, or to
bon cartridge co orrectly, ensure
ight ribbon mou unting pins are s
ge supports.
t wists or folds in n the ribbon.
not catching on n the print head.
oves when you turn the ribbon
of the arrow. If the ribbon does
artridge. Contact ct your place of r
ou believe that t the ribbon is fau
printer cover.
90 050‐9065‐90
nts
ps/Watts Ph hase/Hz
8–1.6A S Single
50 0-60Hz
at you remove a all
ng material.
e tie around the print
nal ribbon cartr ridge. To
e. Locate the rib bbon
d the ribbon m mounting
of the arrow to take up
not move, conta act your
n cartridge.
one it her side o of the top
r.
es on the left an nd
holding it
slack in the ribb bon.
up onto the rib bbon lift
he ribbon lift as ssembly
right side of the e ribbon
ports. Snap the e ribbon
irection of the a rrow to
the print head b back
s freely along th he
ensure that yo ou have
e that:
securely snappe ed
.
advance knob in
s not move, repl lace
ribbon cartridge e
ulty.
080‐9300 Plu us‐QSG