Summary of Contents for Newmatic HGB 3045
- Page 1 HGB 3045 TGB 3045 TGB 4045 TGB 4055 TGB 4055T S C R U B B E R D RY E R Owner Instructions Warning! Read instructions before using the machine www.numatic.co.uk...
-
Page 2: Table Of Contents
S C R U B B E R D RY E R HGB 3045 / TGB 3045 / TGB 4045 / TGB 4055 / TGB 4055T Index PLEASE READ Machine Overview ........ Pages 2-3 BEFORE COMMENCING Control Panel Overview ........ Page 4 OPERATION Machine Set up Guide ........ -
Page 3: Machine Overview
Machine Overview TGB 4045/4055 TGB4055T Batteries HGB 3045 TGB 3045 Batteries TGB 4045/4055 HGB 3045 TGB 3045 Fuses TGB 4045/4055 TGB 4045/4055... -
Page 4: Control Panel Overview
S C R U B B E R D RY E R HGB 3045 / TGB 3045 / TGB 4045 / TGB 4055 Control Panel Overview Battery Charge Level Indicator Vacuum Pick Up On / Off Water Flow On / Off... -
Page 5: Machine Set Up Guide
Fit the isolator key and switch the machine on (See below, TGB 4045/4055/4055T (Fig. A) HGB 3045 & TGB 3045 (Fig.D) NOTE: Wear suitable gloves when inserting fuses. “ Ensure that no metal objects come into contact with battery terminals while the batteries are exposed. -
Page 6: Fitting The Brush / Pad
Machine Set-up Guide ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF BEFORE MAKING ANY ADJUSTMENTS Fitting the Brush / Pad / Turn on water 450mm / 550mm Brush or a Pad. Featuring the Nulock brush system. The brush is simply pushed and twisted to lock, making fitting and removal a simple process. Slide the brush / pad under the brush deck. -
Page 7: Fitting The Hose Guide
Machine Set-up Guide Fitting the Hose Guide The vacuum hose has a U-bend clip which creates a U-bend in the hose preventing water spillage when the vacuum is switched off. If you need to remove the U-bend clip for any reason always ensure it is refitted correctly before you resume operation. NOTE: DO NOT push the vacuum hose onto the floor tool with the floor tool in the raised position. -
Page 8: Handle Height Adjustment
Machine Set-up Guide Handle Height Adjustment Using the handle position lever, lower the handle to a comfortable working position. WHEN HANDLING AND MIXING CHEMICALS Always ensure that chemical manufacturer’s safety guidelines are followed. Only use chemicals recommended for use in auto scrubber-dryers. IMPORTANT Do not operate machine unless the Operator Manual has been read and fully understood. -
Page 9: Lowering The Floor Tool
Machine Operation Raising/Lowering the Floor Tool After preparing the floor (see previous section), we are now ready to set the controls to suit the cleaning conditions. Before any settings can be applied, ensure the brush deck is lowered. Move the floor tool lever to its lower position. -
Page 10: Breakaway Floor Tool
Machine Operation Break-away Floor Tool The floor tool design incorporates a break-away feature. Allowing it to safely disengage from its mounting should it become caught on an obstruction, during forward machine movement. To re-attach the blade to its holder. First loosen the retaining knobs on the floor tool body and slide onto the holding bracket. -
Page 11: Machine Maintenance
Regular Maintenance ALWAYS ENSURE THAT THE MACHINE IS SWITCHED OFF PRIOR TO ANY MAINTENANCE USING THE MASTER CONTROL ON/OFF KEY. REMOVE THE KEY PRIOR TO ANY MAINTENANCE OPERATION. After use, empty waste water tank using emptying hose and flush out with clean water. -
Page 12: Changing Floor Tool Blades
Changing the Floor Tool Blades Always ensure that the machine is switched off prior to any maintenance. To clean the floor tool, remove securing-pin and pull-free from the holder. Rinse the floor tool assembly with clean water and refit. Periodically the floor tool blades should be examined and checked for wear and damage. The blade removal is easy. -
Page 13: Machine Charging
Machine Charging Always ensure that the machine is switched off prior to charging. The battery meter displays the charge level of the batteries; As the machine is used and the batteries are discharged, when fully charged, all meter lights are illuminated. the meter lights will go out from right to left. -
Page 14: Battery Care
UNDER NORMAL DAILY USAGE: Re-charge the machine FULLY after each use regardless of machine operation time. Do not leave the machine in a discharged state. Charging Light Sequence HGB 3045 / TGB 3045 Signal (LED) Meaning Red LED on First Phase (Constant Current Mode) -
Page 15: Traction Tgb 4055T
B AT T E RY S C R U B B E R D RY E R , T R A C T I O N D R I V E TGB 4055T Control Panel Overview Battery Charge Level Indicator On / Off Switch Vacuum Pick Up On / Off Anti Crush Switch... - Page 16 Machine Operation To start: hold either trigger and press the Yellow On / Off Switch For a speed boost when moving the machine press the grey fast once to start the machine. moving lever down. Direction is controlled using the direction switch fitted to the left The speed is controlled by the speed control knob fitted to the side of the handle right hand side of the handle...
-
Page 17: Specifications
Specifications HGB 3045 / TGB 3045 BRUSH WEIGHT 29.0 kg GROSS WEIGHT ( i.e. with liquid) 120 kg BRUSH PRESSURE 21.7 g/cm² NETT WEIGHT ( i.e. NO liquid) 90 kg PAD PRESSURE 23.1 g/cm² POWER SOURCE GELL BATTERY 24 VOLT (2 x 12V) 55Ah CLEANING AREA 800m²/HOUR @ 2 kph... -
Page 18: Rating Label / Personal Protective Equipment / Recycling
About the Machine Rating Label Company Name & Address Machine Description Voltage Frequency Power rating WEEE Logo Ingress Protection Rating Max Gradient CE Mark Weight (ready to use) Machine yr/wk Serial number Machine Description Noise Rating Hand Arm Vibration WEEE (Waste, Electrical and Electronic Equipment) Scrubber dryer Accessories and packaging should be sorted for environmentally-friendly recycling. -
Page 19: Safety Precautions
ORIGINAL INSTRUCTIONS Information for Scrubber Dryer READ MANUAL BEFORE USE COMPONENT INTERVAL INSPECT FOR Mains Lead DAILY Scuffing, cracks, splits, conductors showing Brushes DAILY Bristle damage, wear, drive collar wear Squeegee Blade BEFORE EACH USE Wear, cracks, splits Filters BEFORE EACH USE Clogging and debris retention Tanks AFTER EACH USE... -
Page 20: Schematic Diagram
ORIGINAL INSTRUCTIONS Information for Scrubber Dryer READ MANUAL BEFORE USE Precautions when working with batteries Always wear protective clothing e.g. face visor, gloves and overalls when working with batteries. Whenever possible always use a properly designated and well-ventilated area for charging. Do not smoke or bring naked flames into the charging area. -
Page 21: Recommended Spare Parts
Spare Parts Part No. BRUSHES Part No. HOSES 606028 550 mm Polyscrub Brush 903341 Hose Closure (Bottom Tank) 606550 550 mm Nyloscrub Brush 903341 Hose Closure ( Filling Hose) 606551 550 mm Long Life Brush 900903 Hose Closure (Top Tank) Part No. -
Page 22: Eu Declaration Document
EU Declaration of Conformity www.numatic.co.uk... -
Page 23: Warranty
Warranty T 01460 68600... -
Page 24: Company Address
This Machine Has Been Packed Distributed by: With The Following Brush / Pad Floor Tool NuTab Charging Lead Fuse Pack Signed Numatic International Limited. Chard, Somerset TA20 2GB ENGLAND Tel.: 01460 68600 www.numatic.co.uk Numatic International GmbH. Fränkische Straße 15–19 D-30455 Hannover, DEUTSCHLAND Tel.: 05 11 98 42 16 0 www.numatic.de Numatic International SAS.