Table of Contents
Advertisement
Operation Guide 3210
Alarms and Hourly Time Signal
You can set up to fi ve different alarms. When any one of the alarm times is reached
in the Timekeeping Mode, the watch will sound an alarm beeper or vibrate for about
10 seconds.
The hourly time signal causes the watch to beep or vibrate every hour on the hour.
E-30
Changing the Alarm Time Setting
D button to select the alarm (1 through 5) whose time
1.
In the Alarm Mode, use the
setting you want to change.
Alarm 1 (
)
Alarm 2 (
Hourly Time Signal (
)
E-32
A for about two seconds until the hour digits of the current alarm time
3.
Hold down
start to fl ash.
[SET hold] will appear on the display. After that, the alarm time setting screen
will appear.
4.
Each press of
the hour and the minute digits.
The fl ashing digits are the ones that are selected.
B (+) and D (–) to change the hour and minute
5.
Use
settings.
Holding down either button scrolls the setting at high
speed.
If you are using 12-hour timekeeping, the [P] indicator
will appear for times between noon and 11:59 p.m.
E-34
Stopwatch
The stopwatch measures elapsed time in units of 1/100 seconds up to 23 hours,
59 minutes, 59.95 seconds. Elapsed time returns to zero automatically and timing
continues from there when the maximum limit is reached.
Entering the Stopwatch Mode
1.
In the Timekeeping Mode, press
enter the Stopwatch Mode.
[STW] will appear on the display for about one
second, and then the stopwatch screen will appear.
E-36
Timer
The timer start time can be set in one-minute increments up to 24 hours. The watch till
sound a beeper or vibrate for about 10 seconds when the end of the timer countdown
is reached.
Entering the Timer Mode
1.
In the Timekeeping Mode, press
the Timer Mode.
E-38
)
Alarm 3 (
)
Alarm 5 (
)
Alarm 4 (
)
C causes the fl ashing to move between
C three times to
C four times to enter
Entering the Alarm Mode
C twice to enter the Alarm Mode.
1.
In the Timekeeping Mode, press
[ALARM] will appear on the display for about one second, and then an alarm
setting screen (Alarm 1 through Alarm 5) will appear.
Alarm setting screen
B to select the alarm time or to turn the hourly time signal on or off.
2.
Use
Alarm Types
: Alarm does not sound. (Alarm off)
Alarm sounds only once at the preset time
:
and does not sound again after that.
: Alarm sounds at the preset time each day.
Hourly Time Signal
: Hourly time signal does not sound.
Hourly time signal sounds every hour on
:
the hour.
6.
After all the settings are the way you want, press
The alarm icon appears when an alarm is turned on, while the hourly time signal
icon appears when the hourly time signal is turned on.
Alarm On
7.
To return to the Timekeeping Mode, press
Stopping the Alarm
1.
Pressing any button while the alarm tone is sounding will stop it.
Testing the Alarm
D to sound the alarm.
1.
In the Alarm Mode, hold down
Measuring Elapsed Time
The following shows button operations for elapsed time measurements.
Elapsed Time Measurement
D
D
D
Start
Stop
Restart
Split Time Measurement
D
B
B
Start
Split
Release split
(Time frozen on
(Display returns
display.)
to elapsed time.)
Note
Once started, elapsed time measurement continues until you press the B button to
stop it, even if you change to a different mode and even if the stopwatch reaches the
elapsed time measurement limit.
If you change to another mode while a split time is frozen on the display, the split
will be released.
Setting the Timer Start Time
A for about two seconds until the hour digits of the
1.
In the Timer Mode, hold down
start time start to fl ash.
[SET hold] will appear on the display. After that, the timer start time setting screen
will appear.
If a timer countdown operation is in progress, press D to stop it and then press
B to reset the timer to its start time before performing the above step.
If a timer countdown operation is paused, press B to reset the timer to its start
time before performing the above step.
2.
Each press of
the hour and the minute digits.
The fl ashing digits are the ones that are selected.
B (+) and D (–) to change the hour and minute
3.
Use
settings.
Holding down either button scrolls the setting at high
speed.
To specify a timer start time of 24 hours, set the time to
0H 00'00 on the display.
Hourly time signal screen
E-31
E-33
A to exit the setting screen.
Hourly Time Signal On
C four times.
E-35
D
B
Stop
Reset
D
B
Stop
Reset
E-37
C causes the fl ashing to move between
E-39
Advertisement
Table of Contents
