Table of Contents
Advertisement
Manual Instructions
AEMG-12, AEMG-24, AEMG-24H, AEMG-36, AEMG-36H, AEMG-48
AERB-12, AERB-24, AERB-36, AERB-48, AECRB-12, AECRB-24, AECRB-36, AECRB-48
AEHP-2-12, AEHP-4-24, AEHP-6-36, AEM-G24-B2-36 H, AEM-G12-B4-36
Manual instructions
EN
Installation and Operation
Manual de instrucciones
ES
Uso y mantenimiento
Bedienungshinweise
DE
Installation und Betrieb
Ręczny
PL
Obsługa i konserwacja
GRIDDLE RADIANT
BROILER
HOT PLATE
Manuel talimatları
TK
Kurulum ve Çalıştırma
Manuel d'instructions
FR
Installation et fonctionnement
Manual do instruções
PT
Instalação e Operação
DOCUMENT CODE:
Advertisement
Table of Contents
Related Manuals for ASBER AEMG-12
Summary of Contents for ASBER AEMG-12
- Page 1 Manual Instructions GRIDDLE RADIANT AEMG-12, AEMG-24, AEMG-24H, AEMG-36, AEMG-36H, AEMG-48 BROILER AERB-12, AERB-24, AERB-36, AERB-48, AECRB-12, AECRB-24, AECRB-36, AECRB-48 HOT PLATE AEHP-2-12, AEHP-4-24, AEHP-6-36, AEM-G24-B2-36 H, AEM-G12-B4-36 Manual instructions Manuel talimatları Kurulum ve Çalıştırma Installation and Operation Manual de instrucciones Manuel d’instructions...
-
Page 2: Table Of Contents
asberprofessional.com INDEX ENGLISH MACHINE INTRODUCTION ............................1 INTRODUCTION TO MACHINE & MODELS ....................1 IMPORTANT SAFETY INFORMATION .......................1 SPECIFICATION CHART ..........................1 INSTALLATION ................................2 Transport, handling, unpacking, location ....................2 Manufacturer’s identification label description ..................2 Installation and assembly ........................3 2.3.1 UNCRATING .............................3 2.3.2 INSTALLATION OF LEGS ........................3 Gas Connections ............................4 2.4.1 MANUAL SHUT OFF VALVE ......................4... -
Page 3: Machine Introduction
1.1 INTRODUCTION TO MACHINE & MODELS All equipment manufactured by ASBER. is for use with the type of gas specified on the rating plate and for installation will be in accordance with National Fuel Gas Code ANSI Z223.1 (latest edition) Instruction to be followed in the event the user smells gas shall be posted in a prominent location. -
Page 4: Installation
2.4 Gas Connections 2.1 Transport, handling, unpacking, location Upon receiving your new ASBER Equipment, check the package and the machine for any damages that may have occurred during transportation. Visually inspect the exterior of the package. If damaged, open and inspect the contents with the carrier. Any damage should be noted and reported on the delivering carrier’s receipt. -
Page 5: Installation And Assembly
asberprofessional.com 2.3 Installation and assembly SHIPPING DAMAGE CLAIM PROCEDURE The equipment is inspected and crated by skilled personnel before leaving our factory. The transportation company assumes full responsibility for safe delivery upon acceptance of this equipment. If shipment arrives damaged: Visible loss or damage: Note on freight bill or express delivery and signed by person making delivery. -
Page 6: Gas Connections
2.4.2 PRESSURE REGULATOR Commercial cooking equipment must have a pressure regulator on the incoming service line for safe and efficient operation; the gas pressure regulator supplied by ASBER must be installed at the gas inlet of each piece of equipment. -
Page 7: Pressure Regulator Conversion
asberprofessional.com 2.4.4 PRESSURE REGULATOR CONVERSION A. Remove cap and snap out plastic plunger from bottom of cap. B. Turn plunger over and snap back in original location. C. Re-insert the cap assembly into the regulator and tighten. Failure to install the pressure regulator will void the appliance warranty The fryer needs to be restrained to prevent tipping when installed in order to avoid the splashing of hot liquid. -
Page 8: Clearances
asberprofessional.com 2.6 CLEARANCES The appliance area must be kept free and clear of all combustibles SRR, SRMR Series products are for installation in Non-Combustible locations only. MODEL NON COMBUSTIBLE CONSTRUCTION BACK SIDES GRIDDLE RADIANT 0 Inches 0 Inches BROILER 0 Inches 0 Inches 0 Inches 0 Inches... -
Page 9: Operation
When lighting pilots and checking for leaks, do not stand close to the combustion chamber All ASBER appliances are adjusted and tested before leaving the factory, effectively matching them to sea level conditions. Adjustments and calibrations to assure proper operation may be necessary on installation to meet local conditions. -
Page 10: Top Burners
asberprofessional.com 3.3.1 TOP BURNERS All top section burners are equipped with constant burning pilots. These are to be manually lighted immediately after the gas is turned on and can be rechecked for proper adjustment. All adjustments can be made with a screw driver to the brass pilot valve accessible through the valve cover. -
Page 11: Maintenance
asberprofessional.com MAINTENANCE 4.1 Cleaning 4.1 CLEANING For continued performance efficiency and longevity of your Fryer it is essential to carry out a good maintenance program. 4.1.1 DAILY OPEN BURNERS / HOT PLATES Remove all top grates. Lift off the burners heads and venturies by raising the head slightly, sliding to the rear and lifting upwards. -
Page 12: Trouble Shooting
asberprofessional.com TROUBLE SHOOTING PROBLEM PROBLEM CAUSE SOLUTION BURNER AND/OR PILOTS GAS SUPPLY TO COOKING TURN ON GAS SUPPLY NOT TURN ON EQUIPMENT IS OFF GAS TYPE VERIFY CORRECT GAS CONTACT LOCAL GAS GAS SUPPLY PRESURE UNIT PRODUCING CARBON SUPPLIER DEPOSITS PRIMARY AIR NOT ADJUST AIR SHUTTER ADJUSTED PROPERLY... -
Page 13: Warranty
ASBER shall not be liable whether in contract or in tort or under any other legal theory for loss of revenue or profit, or for any substitute use or performance or for incidental, indirect, special or consequential damages, or for any other loss or cost of similar type. - Page 14 ASBER Circuito Exportación N° 201 Parque Industrial Tres Naciones San Luís Potosí, S.L.P. México 13105 NW 47th Ave Miami, Fl. 33054 www.asberprofessional.com MULTI-SOLUTION MANUFACTURER OF FOODSERVICE EQUIPMENT...
Need help?
Do you have a question about the AEMG-12 and is the answer not in the manual?
Questions and answers