Table of Contents
Advertisement
w) Use the power tool, accessories and tool bits etc. in accordance with these instructions and in the manner intended for the particular type of power tool, taking
into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous
situation.
Service
x) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
Safety Warnings Common for Polishing Operations.
y) This power tool is intended to function as a polisher only. Read all safety warnings, instructions, illustrations and specifications provided with this power tool.
Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
z) Operations such as sanding, grinding, wire brushing, or cutting off are not recommended to be performed with this power tool. Operations for which the power tool
was not designed may create a hazard and cause personal injury.
aa) Do not use accessories which are not designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does
not assure safe operation.
bb) The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can
break and fly apart.
cc) The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately
guarded or controlled.
dd) The arbor size of wheels, flanges, backing pads or any other accessory must properly fit the spindle of the power tool. Accessories with arbor holes that do not
match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.
ee) Do not use a damaged accessory. Before each use inspect the accessory such as backing pad for cracks, tear or excess wear. If power tool or accessory is
dropped, inspect for damage to install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane
of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.
ff) Wear personal protective equipment. Depending on application, use a face shield, safety goggles or safety glasses. As appropriate, wear dust mask, hearing
protectors, gloves and workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris
generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high intensity
noise may cause hearing loss.
gg) Keep bystanders a safe distance away from work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpiece or of a
broken accessory may fly away and cause injury beyond immediate area of operation.
hh) Hold power tool by insulated gripping surfaces only when performing an operation where the cutting accessory may contact hidden wiring or its own cord. Cutting
accessory contacting a "live" wire may make exposed metal parts of the power tool "live" and shock the operator.
ii) Position the cord clear of the spinning accessory. If you lose control, the cord may be cut or snagged and your hand or arm may be pulled into the spinning
accessory.
jj) Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your
control.
kk) Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your
body.
ll) Regularly clean the power tool's air vents. The motor's fan will draw the dust inside the housing and excessive accumulation of powdered metal may cause electrical
hazards.
mm) Do not operate the power tool near flammable materials. Sparks could ignite these materials.
nn) Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
Kickback and Related Warnings
Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating
accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory's rotation at the point of the binding.
For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material
causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on direction of the wheel's movement at the point of
pinching. Abrasive wheels may also break under these conditions.
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.
oo) Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use auxiliary handle, if provided, for maximum
control over kickback or torque reaction during start up. The operator can control torque reactions or kickback forces, if proper precautions are taken.
pp) Never place your hand near the rotating accessory. Accessory may kickback over your hand.
qq) Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in a direction opposite to the wheel's movement at
the point of snagging.
rr) Use special care when working corners, sharp edges etc. Avoid bounding and snagging the accessory. Corners, sharp edges or bounding have a tendency to snag
the rotating accessory and cause loss of control or kickback.
ss) Do not attach a saw chain, woodcarving blade, or toothed saw blade. Such blades create frequent kickback and loss of control.
WARNING: When using electric tools, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and personal injury, including but
not limited to the following:
Grounding Instructions
tt) The Orbot Micro should always be electrically grounded while in use to protect the operator from electric shock. This tool is equipped with an approved three-
conductor cord and three-prong grounding type plug to fit the proper grounding type receptacle. The green or green/yellow conductor wire in the cord is the
grounding wire. NEVER CONNECT THE GREEN OR GREEN/YELLOW WIRE TO A LIVE TERMINAL. If there is any doubt as to whether the wall receptacle is properly
grounded, you should have it checked by a qualified electrician.
WARNING: DO NOT UNDER ANY CIRCUMSTANCES CUT OR REMOVE THE THIRD (GROUND) PRONG FROM THE POWER CORD PLUG.
2
Advertisement
Table of Contents
