Page 1
MF253V Let’s go Getting started with your device...
Page 2
ZTE Corporation. The manual is published by ZTE Corporation. We reserve the right to make modifications on print errors or update specifications without prior notice. Version No. : R1.0...
Page 3
Getti ng to K Know Yo our Dev Appea arance OTE: ease use the original exte ernal antenna a if necessary Interfa face Desc cription B jack Insert t the device e to USB int terface. Ether rnet connect tions to com mputer.
Page 4
Indica ators Indicat State Description Power is on and d external pow wer supply is Blue on working normall POWER Power is off or r external pow wer supply is working abnorm mally. Wi-Fi works normally wit th no data Blue on ransmission.
Page 5
Indicat State Description ransmission. The network cab ble is not conne ected. OTE: The ph one function n needs the n etwork supp ort. Conn necting Your D evice Follow the picture to connect y your device Please r refer to the c chapter “Ac ccessing the e Internet”.
Configuring Your PC The following procedure describes how to configure the Internet Protocol in the Windows 7 for your Wi-Fi connection. Right-click Network and select Properties. Select Change adapter settings. Right-click Wireless Network Connection and select Properties. Select Internet Protocol Version 4 (TCP/IPv4) and click Properties.
Page 7
Select Obtain an IP address automatically and Obtain DNS server address automatically, and click OK.
Accessing the Internet Before accessing the Internet, please make sure that the following operations are finished. Your device is connected via a network cable or Wi-Fi. Your PC is configured. To access the Internet: Log in the CPE configuration page. 1.
Page 9
OTE: If y you change th he operation mode, the de evice will be e restarted au utomatically. t the detail p parameters for the oper ration mode Voice e Funct Maki ing a Cal You can n make a call through (U) )SIM card.
Page 10
WPS Function Your device supports WPS function. You can use this function to connect the client to your device. Power on your device, and enable the Wi-Fi function on your device. Enable the WPS function. Please check the WPS Setting on the CPE Configuration Page. Press the WPS button on your device to start Wi-Fi Protected Setup authentication process.
Page 11
OTE: Set the c client to obta ain an IP add dress automa atically. For t the detailed p procedure, re efer to Confi figuring Your PC. The client gets a an IP address s, for exampl le, 192.168.0 0.101. Sele ect the SSID (wireless net...
Page 12
OTE: You can n find the def fault SSID on n the label of f your device ter the passw word, and the en click OK. OTE: You may y need to en nter the passw word for the Wi-Fi conn ection.
Page 13
Symptoms Possible Problems/ Solutions please disconnect this first. After dialing the last digit I hear nothing /silence. When you have finished dialing you can press the # key or wait 4~8 seconds to connect the call. Internet Related Problems Symptoms Possible Problems/ Solutions ...
Page 14
Symptoms Possible Problems/ Solutions the label on the device. The default password of the CPE Configuration Page is admin. If you changed the password and forgot the new password, you need to restore the device to the factory default settings.
Warning and Notice To the Owner • If inadequately shielded, some electronic devices may be affected by the electromagnetic interference caused by the device, such as the electronic system of vehicles. Consult the manufacturers of such devices before using the device if necessary. •Operating the device may interfere with medical instruments such as hearing aids and pacemakers.
Any other cause beyond the range of normal usage intended for the product. End users have no right to reject or return the product, or receive a refund for the product from ZTE under the above-mentioned situations.
Page 17
not limited to lost profits, interruption of business, cost of capital, cost of substitute facilities or product, or any downtime cost. FCC Caution: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
Need help?
Do you have a question about the MF253V and is the answer not in the manual?
Questions and answers