Related Manuals for OmniBlend I
Summary of Contents for OmniBlend I
- Page 1 OWNER’S MANUAL OmniBlend I OmniBlend (Pty) Ltd SOUTH AFRICA www.omniblend.co.za Read and save these instructions...
-
Page 2: Table Of Contents
Table of Contents LET’S GET STARTED SERVICE & REGISTRATION IMPORTANT SAFEGUARDS PARTS & FEATURES ABOUT THE BLADES HOW TO USE THE TAMPER? CONTROL PANEL HINTS FOR SETTING SPEEDS CARE AND CLEANING SPECIFICATIONS... -
Page 3: Let's Get Started
Please read all the safety information, warnings, and instructional material found in this booklet before getting started. Set your OmniBlend machine on a dry, level surface. Make sure that the power switch is set to Off, and that the machine is plugged into a grounded electrical outlet. -
Page 4: Service & Registration
SERVICE & REGISTRATION OMNIBLEND SERVICE Record the serial number of your OmniBlend on the warranty form provided with the machine for future reference. These numbers can be found on the back of the motor base. Before returning this product for any reason, including repair, first contact OmniBlend Customer Service at 021 012 5999, email service@omniblend.co.za, or contact your local dealer. -
Page 5: Important Safeguards
IMPORTANT SAFEGUARDS To avoid the risk of serious injury when using your OmniBlend blender, basic safety precautions should be followed, including the following. IMPORTANT INSTRUCTIONS FOR SAFE USE Do not leave your OmniBlend blender unattended when operating. In case of a technical failure, contact OmniBlend for any repairs or servicing requirements. - Page 6 OmniBlend owner. If the Overload Protection kicks in, the machine will stop operating suddenly. Leave the machine to cool down for 5 to 10 minutes, and then (while the machine is still connected to power), press the Overload Button on the bottom of the machine.
- Page 7 8. Keep hands and utensils out of container while blending to reduce the risk of severe injury to persons or damage to the blender. A silicon scraper or spatula may be used, but only when the OmniBlend blender is not running.
- Page 8 13. Always operate blender with lid and lid plug firmly in place. The lid plug should be removed only when adding ingredients and when using the tamper. 14. When blending hot liquids or ingredients, use caution; spray or escaping steam may cause scalding and burns. Fill the jug 1/3 or max ½...
-
Page 9: Parts & Features
PARTS & FEATURES 2-Part Lid: your new machine has our latest lid design. It is easy to put on and take off, and easy to clean. Always use the lid and the lid insert when the machine is in operation. The 1.5ltr jug has a square lid, the 2ltr jug has a round lid. - Page 10 For your safety the OmniBlend blenders are equipped with Overload Protection. If the motor shuts off suddenly, leave the machine to cool down for 5-10 minutes, and then press the black Overload Button on the bottom of the machine.
- Page 11 Overload Button...
-
Page 12: About The Blades
ABOUT THE BLADES The OmniBlend machine comes standard with the multi-purpose blade. The blade assembly has stainless steel ball bearing. This blade fits both the 1.5 Ltr and 2 Ltr container. Additional containers with blades may be purchased separately. Blade assemblies can also be purchased separately. The blade assembly comes with a 1 year warranty. -
Page 13: How To Use The Tamper
HOW TO USE THE TAMPER? The tamper allows you to accelerate the process of very thick and/or frozen mixtures that cannot be processed in a regular blender. Using the tamper maintains circulation by preventing air pockets from forming. While the machine is running, and only through the lid plug opening, use the tamper to press ingredients into the blades as you make frozen ice creams and nut butters, or purée fruits and vegetables. - Page 14 The splash disk (near the top of the tamper) and lid prevent the tamper from touching the blades when the lid is secured properly in the locked position. The container should not be more than two-thirds full when the tamper is used during blending.
-
Page 15: Control Panel
CONTROL PANEL 1. On/Off Switch: Push up to turn On (|). Push down to turn Off (O). 2. Speed Dial: MIN indicates the lowest speed available. Turn to MAX to increase the speed. Always make sure that the MAX/MIN Turn Dial is set to MIN before pushing the On/Off Switch to the On position. Do not start your machine on MAX speed. - Page 16 When on the MAX, if the food does not circulate, the machine may be overloaded or may have trapped an air bubble. Carefully remove the lid plug while making sure the lid stays firmly in place. Release the air bubble by inserting the tamper through the lid plug opening.
-
Page 17: Care And Cleaning
CARE AND CLEANING Container: Rinse the jug after each use with warm water. To prepare your new machine for initial use, follow the steps under Normal Cleaning. This will clean the unit, and break-in the motor. Normal Cleaning: 1. Fill one third of the container with warm water and add a couple drops of dish wash liquid. 2. - Page 18 IMPORTANT: To ensure continued and effective performance, do not put the container, lid, or lid plug in the dishwasher. WARNING Electrical Shock Hazard. Disconnect power before cleaning machine. Failure to follow instructions can cause death or electrical shock. Motor Base: 1.
-
Page 19: Specifications
240 V, 50/60 Hz, 11.5 A Uses a R.S.A. three—prong grounded cord. Dimensions: Height: 52 cm Width: 18,42 cm Depth: 22,35 cm To view the complete line of OmniBlend products, visit www.omniblend.co.za OmniBlend (Pty) Ltd, 3 St. Georges Mall, The Colosseum - Unit 505, Cape Town, 8001 021 012 5999...