Lcd Display - Craftsman 315.EL2200 Operator's Manual

LCD DISPLAY

See Figures 6 - 7, pages ii and iii.
When the radio/charger is connected to a power supply
and in the ON position, the LCD display will show the
time, frequency, mode, and settings.
NOTE: The illustrations of the LCD display shown in this
manual are only examples of the frequencies you may see
on your radio/charger and are not the exact frequencies
that you may choose to listen to.
MENU NAVIGATION BUTTONS
See Figures 6 - 7, pages ii and iii.
Use the menu navigation buttons to turn the radio/charger
on and off, control the volume, change frequencies, toggle
between modes and set the time.
TURNING THE RADIO/CHARGER ON AND OFF:
Press the ON/OFF button to turn the radio/charger ON
and OFF.
When the radio/charger is on and a battery pack is
connected as the power supply, the [
shown in the LCD display. If the battery charge is low, a
flashing low battery indicator will be displayed [
the radio is connected to an AC power supply, the battery
indicator will disappear.
ADJUSTING THE VOLUME:
When the radio/charger is turned ON, the unit will return
to the last volume setting used.
 To increase the volume, press the VOL + button.
 To decrease the volume, press the VOL - button.
SWITCHING MODES:
To switch modes, press the MODE button. The selected
mode will be displayed above the frequency. Press the
MODE button until the desired mode is selected. There
are four modes:
 FM mode
 AM mode
 AUX mode
 BLUETOOTH mode
®
AM/FM TUNING:
Use the SCAN and SCAN
to the desired radio frequency. The selected frequency is
displayed on the LCD.
 Press the SCAN
button to tune to a lower frequency
and press the SCAN
frequency.
NOTE: Briefly press either button (not press and hold)
to tune one frequency step at a time. Press and hold
either button to quickly find the next frequency with
clear reception.
OPERATION
] symbol will be
buttons to manually tune
button to tune to a higher
 To decrease interference or electrical noise, adjust the
position of the antenna or move the radio/charger to a
higher elevation. The antenna folds into the handle and
out of the way when not in use.
STORING A PRESET IN MEMORY:
The memory feature saves up to 20 frequencies as
presets in the radio's memory. You can save up to ten (10)
frequencies each for FM and AM modes.
 Tune to the desired AM or FM frequency.
 Press and hold the PRESET button until the word
"MEMORY" and the preset position number flash on
the screen.
 Press the SCAN
preset position number.
NOTE: There are ten (10) preset positions for FM and
ten (10) for AM. Only one station can be saved in each
preset position.
 Press the PRESET button again to store the frequency.
To tune to presets (FM or AM mode):
 Press and release the PRESET button to cycle through
each preset position number and its associated
]. If
frequency.
SETTING THE CLOCK:
The time appears on the LCD display when the radio/
charger is on.
 Press and hold the CLK/DSPY button until the "hour"
display blinks.
 Press the VOL + or VOL - button to select the hour.
NOTE: Time is displayed in 12-hour format only. To
select an hour that is after noon and before midnight,
cycle the hours until "PM" appears in the display.
 Press and release the CLK/DSPY button to lock in the
hour setting. "Minutes" will begin to blink.
 Press the VOL + or VOL - button to select the desired
number.
 Press and release the CLK/DSPY button again to
confirm the time.
USING A PHONE/MP3 PLAYER (NOT
INCLUDED) WITH THE RADIO/CHARGER
See Figure 8, page iii.
 Press the MODE button until AUX mode is highlighted.
 Connect one end of a 3.5 mm audio patch cord
(maximum 8 in. long) to the device.
 Connect the other end of the 3.5 mm patch cord to the
auxiliary input jack.
 The phone/MP3 player must be on and in play mode
for sound to be heard through the speakers.
10 - English
or SCAN button to choose a