Using An External Speaker - Craftsman 315.EL2200 Operator's Manual

 All phone/MP3 player controls can be used normally
while connected to radio.
NOTE: Volume for any device connected through the
auxiliary input jack can be adjusted using the volume
control for that device or by using the radio's VOL + or
VOL - button.
 Turning the radio/charger off will NOT turn the phone/
MP3 player off.
 The auxiliary input jack DOES NOT provide charging
function.
 For complete operating instructions for the connected
device, always refer to the manual that was included
with your device.
USING THE USB DEDICATED CHARGING
PORT
See Figure 9, page iii.
The USB dedicated charging port provides charging
power of 5 Volts DC at up to 2 Amps for your cell phone,
MP3 player, tablet, or other USB devices.
NOTICE:
Attempting to charge devices rated more
than 2 Amps could damage the USB dedicated
charging port and/or the device.
 Connect one end of a USB cable (not provided) to your
USB device.
 Connect the other end of the USB cable (not provided)
to the USB dedicated charging port to begin charging
the device.
NOTE: The USB dedicated charging port provides
power only; it does not provide any communication
capabilities.
 When the radio/charger is operating on battery power,
the USB dedicated charging port will continue to function
for approximately 1 hour after turning the radio OFF. If
the radio remains inactive after this time, charging will
stop. Turn the radio on to resume operation.

USING AN EXTERNAL SPEAKER/

RECORDING DEVICE (NOT INCLUDED) WITH
THE RADIO/CHARGER
See Figure 10, page iii.
 Connect one end of a 3.5 mm audio patch cord
(maximum 8 in. long) to the device.
 Connect the other end of the 3.5 mm patch cord to the
auxiliary output jack.
 External speakers must be on for sound to be heard.
Recorders must be on and in record mode to record
sound.
OPERATION
NOTE: Use recording devices only in accordance with
manufacturer's instructions, and all local, state, and
federal laws when dealing with copyrighted material.
 All external speakers/recorder controls can be used
normally while connected to the radio/charger.
 Turning the radio/charger off WILL NOT turn the
external speakers/recorder off.
 The auxiliary output jack DOES NOT provide charging
function.
 For complete operating instructions for all external
speakers and recorders, always refer to the manual
that was included with your model.
USING A BLUETOOTH
(NOT INCLUDED) WITH THE RADIO/
CHARGER
See Figure 11, page iv.
 Press the MODE button until the ( ) BLUETOOTH
mode is highlighted.
 When the radio/charger is switched to ( )
BLUETOOTH
BLUETOOTH
LCD display.
NOTE: The radio/charger will automatically attempt
to connect to the last device it was paired to. If a
connection cannot be established within five seconds,
the radio/charger will make itself available to other
BLUETOOTH
 BLUETOOTH
the radio and set to search/scan in order to pair with
the radio/charger.
 Select "Craftsman Stereo" from your device's list of
available BLUETOOTH
the radio/charger. No password or PIN is required for
connection.
 When the device has successfully paired with the
radio/charger, "bt" will stop flashing.
NOTE: When a device is paired to the radio/charger,
information for connecting to the device is saved in the
radio/charger's memory.
 When streaming audio from a BLUETOOTH
device, press the SCAN
the previous or next track. Briefly press and release the
PRESET button to cycle between pausing and playing
the audio.
NOTE: These controls may not be supported by the
BLUETOOTH
11 - English
ENABLED DEVICE
®
mode, the unit will attempt to pair to a
®
enabled device and "bt" will flash in the
®
enabled devices.
®
enabled devices must be within 30 ft. of
®
signals to pair the device and
®
or SCAN
device and/or application you are using.
®
®
enabled
®
button to go to