Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Bissell SPINWAVE 2039 SERIES
Summary of Contents for Bissell SPINWAVE 2039 SERIES
- Page 1 SPINWAVE ™ _______________ USER GUIDE 2039 SERIES...
-
Page 2: Important Safety Instructions
READ ALL INSTRUCTIONS BEFORE USING YOUR SPINWAVE™. When using an electrical appliance, basic precautions should be observed, including the following: WARNING » Use only BISSELL cleaning » Do not pull or carry by cord, use cord as a handle, close a door on... -
Page 3: Table Of Contents
Thanks for buying a BISSELL SpinWave™ We love to clean and we’re excited to share one of our innovative products with you. We want to make sure your hard surface floor cleaner works as well as it does today for years to come, so this guide has tips on using (pages 6-8), maintaining (pages 9), and if there is a problem, troubleshooting (page 10). - Page 4 Getting to Know Your SpinWave™ Handle Spray Nozzle Digital Controls In-Use Cord Clip Clean Water Tank Quick Release™ Cord Wrap Low Profile Foot Lower Cord Wrap Power Spin Pads www.BISSELL.com...
-
Page 5: Assembly
Assembly WARNING Do not plug in your SpinWave™ until you are familiar with all instructions and operating procedures. Your BISSELL SpinWave™ machine comes in two easy-to-assemble components and does not require any tools to assemble. Insert handle into body of... - Page 6 Attaching Mop Pads Your BISSELL SpinWave™ may have come The Soft Touch Pad is best for with two different mop pads: everyday use on delicate flooring like sealed hardwoods and laminate. The Scrubby Pad is best used to power through tough, sticky messes.
- Page 7 A few notes about filling the clean water tank: • Fill with warm (140°F/60°C MAX) tap water and add the appropriate BISSELL solution. DO NOT USE BOILING WATER. DO NOT HEAT WATER OR TANK IN MICROWAVE. www.BISSELL.com...
- Page 8 ATTENTION: This machine is designed to be used only on sealed hard floors and should not be used on carpet or rugs. For best cleaning results, sweep or vacuum the floor surface prior to using the BISSELL SpinWave™. This is to avoid scratching or damaging floors from sharp debris. Recline...
- Page 9 NOTE: Any solution remaining in the clean water tank should be emptied prior to machine storage. NOTE: Store cleaner in a protected, dry area. Since this product uses water, it must not be stored where there is danger of freezing. Freezing may damage internal components and void the warranty. www.BISSELL.com...
-
Page 10: Troubleshooting
Test outlet with a small appliance like a cell phone charger, and use another outlet if needed Fuse/breaker outlet blown Reset the breaker Machine is Cap of clean water tank is not Remove the clean water tank and leaking closed properly re-apply the cap www.BISSELL.com... -
Page 11: Warranty
Service If your BISSELL product should require service: Contact BISSELL Consumer Care to locate a BISSELL Authorized Service Center in your area. If you need information about repairs or replacement parts, or if you have questions about your warranty, contact BISSELL Consumer Care. - Page 12 (and millions of your closest friends) For Parts and Supplies, go to BISSELL.com and know what you think! enter your model number in the search field. For cleaning tips and more visit www.BISSELL.com or find us at: BISSELL BISSELLClean BISSELLClean BISSELL BISSELL ©2017 BISSELL Homecare, Inc...
Need help?
Do you have a question about the SPINWAVE 2039 SERIES and is the answer not in the manual?
Questions and answers
It will not turn on. Tried all the tips in the handbook
The Bissell SPINWAVE 2039 SERIES may not turn on due to the following possible causes:
1. Power Cord Issues – Ensure the power cord is properly plugged into a working outlet.
2. Electrical Outlet Problem – Try plugging the appliance into a different outlet to check if the issue is with the electrical source.
3. Grounding Issue – The appliance must be plugged into a properly installed and grounded 120-volt outlet.
4. Frozen Components – If the unit was stored in freezing conditions, internal components may be damaged, preventing it from working.
5. Power Switch Off – Ensure the power switch is turned on.
If the issue persists, further troubleshooting or service may be required.
This answer is automatically generated
There is steam comingfrom the front at the end of holding stick
The Bissell SPINWAVE 2039 SERIES is not a steam cleaner. If steam appears to come from the front while in use, it may be due to a malfunction such as overheating, a damaged cord, or improper use. Inspect the cord for damage, ensure the machine is used only on hard floors moistened by the cleaning process, and confirm all parts are properly assembled. If the issue persists, stop using the machine and contact a qualified technician.
This answer is automatically generated