Advertisement
Creating Special Labels
Creating Labels for Patch Panel
You can create the optimal labels for your patch panel
by setting the label length and number of blocks.
Separator
Blocks length
Blocks number
1. Press
.
2. Select the length type with
/
and then press
In this example, we will select "Blocks".
Blocks: Sets the length by block length.
Label: Sets the length by label length.
3. Enter the blocks length and then press
Setting range: 0.25 to 30 cm
4. Enter the blocks number and then press
In this example, we will enter "3".
Setting range: 1 to 50
5. Select the type of separator with
/
In this example, we will select "Line".
6. Select the orientation with
/
and then press
In this example, we will select "Hori.".
Hori.
Vert.1
Vert.2
7. Enter the text.
You can create labels with sequence numbers.
For details,
"Creating Labels with Block Sequence Numbers Assigned"
8. Press
.
Creating Labels for Block-66
You can create labels for Block-66 so that large numbers of
connectors can easily be identified.
Separator
Blocks length
Blocks number
1. Press
+
.
2. Select the length type with
/
and then press
In this example, we will select "Blocks".
Blocks: Sets the length by block length.
Label: Sets the length by label length.
3. Enter the blocks length and then press
Setting range: 0.25 to 30 cm
4. Enter the blocks number and then press
In this example, we will enter "4".
Setting range: 1 to 50
5. Select the type of separator with
/
In this example, we will select "Line".
6. Select the orientation with
/
and then press
In this example, we will select "Hori.".
Hori.
Vert.1
Vert.2
7. Enter the text.
You can create labels with sequence numbers.
For details,
"Creating Labels with Block Sequence Numbers Assigned"
8. Press
.
Creating Labels for Faceplate
Text can be automatically placed at the center of a block.
This enables you to easily create a label suitable for the size of
the area where it will be affixed.
Label length
Block
Block
Blocks number
1. Press
.
2. Enter the label length and then press
Setting range: 1 to 99.9 cm
3. Enter the blocks number and then press
In this example, we will enter "2".
Setting range: 1 to 50
4. Select the orientation with
/
and then press
In this example, we will select "Hori.".
Hori.
Vert.1
Vert.2
5. Enter the text.
6. Press
.
Creating Labels for Punch Block
You can create labels to identify at a glance the numbers for the
wires or pins connected to a punch block.
Upper count
1. Press
2. Select the blocks type with
In this example, we will select "4pairs".
.
Blank: Creates a table of two rows and one column.
.
3. Select the text type with
In this example, we will select "Pins".
.
and then press
.
4. Enter the upper count and then press
In this example, we will enter "1".
.
5. Enter the lower count and then press
In this example, "25" is entered automatically.
6. Enter the label length and then press
Setting range: 1 to 99.9 cm
7. Press
Creating Labels to Wrap Around Cable
You can repeatedly print text so that it can be seen
+
regardless of the angle from which the cable is viewed.
Margin
1. Press
2. Select the length type with
In this example, we will select "Length".
Dia: Sets the length by cable diameter.
.
Length: Sets the length by label length.
3. Enter the label length and then press
Setting range: 1 to 99.9cm
4. Select On or Off of repeat text with
.
In this example, we will select "On".
.
On
Off
and then press
.
5.
Select the type of margins with
.
In this example, we will select "Long".
6. Enter the text.
7. Press
Creating Labels to Wrap around Cable
like a Flag
This label is useful for differentiating cables because the flag
portion of the label wrapped around the cable is easy to see.
Block 1
Text length
1. Press
2. Select the setting method of space length with
press
In this example, we will select "Length".
Dia: Sets the length by cable diameter.
Length: Sets the length by space length.
3. Enter the space length and then press
Setting range: 0.25 to 30 cm
.
4. Enter the text length and then press
Setting range: 0.25 to 30cm
.
5. Select the type of separator with
In this example, we will select "Line".
.
6. Select the orientation with
In this example, we will select "Hori.2".
Hori.1
Hori.2
Vert.1
Vert.2
7. Enter the text of block 1.
8. Enter the text of block 2.
9. Press
Lower count
.
/
and then press
/
and then press
Pins
Seri.
Blank
.
.
.
.
Label length
Tape width
Margin
.
/
and then press
.
/
and then press
/
and then press
.
+
Space length
Block 2
Separator
+
.
/
.
.
.
/
and then press
/
and then press
.
Creating Multiple Labels at Once
+
You can create many labels at once.
Label length
Margin
Labels number
1. Press
+
.
.
2. Select the label length with
Auto: Automatically adjusts the label length depending on the length of text.
Set: Sets the label length.
Setting range: 1 to 99.9 cm
3. Enter the labels number and then press
.
In this example, we will enter "3".
4. Select the type of margins with
5. Select the orientation with
In this example, we will select "Hori.".
Hori.
Vert.1
Vert.2
6. Enter "Cable" and then press
Similarly for other labels, enter text and press
7. Press
.
Creating Sequentially Numbered Labels
The number is automatically incremented each time a label is printed.
Up to four digits including numbers (0 to 9) and alphabet letters (a to z and
A to Z) can be entered.
1. Press
.
2. Enter the start value of the sequential numbers and then press
In this example, we will enter "0001".
3. Select the number of repetition with
In this example, we will select "2 times".
4. Press
+
.
.
5. Select "Print copies" with
6. Enter the number of print copies and then press
In this example, we will enter "6".
7. Select "Start print?" with
Printing starts.
.
Creating Labels with Block Sequence Numbers Assigned
+
You can assign sequential numbers to blocks.
Up to four digits including numbers (0 to 9) and alphabet letters (a to z and
A to Z) can be entered.
.
Block 1
Block 2
Create the blocks in advance.
In this example, we have created three blocks.
1. Press
+
.
2. Enter the start value of the sequential numbers and then press
In this example, we will enter "CN01".
Sequential numbers are automatically assigned to block 2 and block 3.
3. Select the number of repetition with
In this example, we will select "1 time".
4. Press
.
Creating Labels with Symbol
1. Press
.
2. Select a category with
3. Select a symbol with
and then
4. Press
.
MEMO
• For available symbols, see "Symbol List" on the separate sheet.
• If you transfer your original symbols from your computer, the symbols are saved in
the "Downloaded" category. For more details, see LW-Z700 User's Guide (PDF
version), which is available from your local Epson website.
.
Creating Barcode Labels
.
MEMO
• You may not be able to add a barcode depending on
the label type you create.
• Only up to two barcodes can be inserted in one label.
Supported barcode types:
EAN-8, EAN-13, CODE128, CODE39, QR CODE, ITF, CODABAR, UPC-A, UPC-E
1. Press
.
2. Select an item with
Move on to the next options until the setting is complete.
3. Enter the alphanumeric characters for the barcode and then press
4. Press
.
Margin
Tape width
/
and then press
.
.
/
and then press
.
/
and then press
.
.
.
.
/
and then press
.
/
and then press
.
.
/
and then press
.
Block 3
.
/
and then press
.
/
and press
.
/
and press
.
/
and press
.
.
Advertisement
