Table of Contents
Advertisement
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Snow Peak GS-011
Summary of Contents for Snow Peak GS-011
- Page 1 Instruction Manual GS-011...
-
Page 2: Table Of Contents
TABLE OF CONTENTS 1. Safety Precautions 2. Explanation of symbols used 2-1 WARNING 2-2 CAUTION 3. Fuel Recommendations 4. GS-010 GigaPower WG Stove contains the following 5. Description of components 6. Using the GigaPower WG STOVE 6-1 Stove Assembly and Preparation for Burning 6-2 Lighting the stove, burning and flame control 6-3 Extinguishing the burner flame 6-4 Disassembly and Storage... -
Page 3: Safety Precautions
Ball spring Maintenance grease 1. Safety Precautions Snow Peak products are designed with safety in mind. However, improper handling/operation may result in accidents such as fire and/or burns. For optimal results, please read these instructions carefully and make yourself familiar with their contents. When using the stove, keep the instruction... -
Page 4: Explanation Of Symbols Used
2. Explanation of symbols used In this instruction manual the following safety precautions are used. Please make yourself familiar with their meanings before reading the main text of this manual. WARNING If the precautions under this heading are not observed, bodily harm such as severe or fatal injuries may result. - Page 5 7. „Troubleshooting“, pages 19-21; repair immediately. If the leak cannot be repaired, contact the dealer where this product was purchased or contact Snow Peak Customer Service. Never try to light the stove when a fuel leak is present. Make sure that the fuel hose is securely connected. Never bend or pull the fuel hose while the stove is burning.
- Page 6 Damage may be caused to the environment due to fire or other hazards. Use only the Snow Peak fuel bottle to prevent unnecessary hazards. Fuel bottles manufacturered by other companies may not securely fit the fuel pump and/or the bottle cap. This may result in fuel leaks. Fuel leaks may cause fire hazards.
- Page 7 To transport the fuel, use only a container designed for white gasoline fuel. For storage and transportation refill the gasoline in a special container such as the GigaPower Fuel Bottle. Carefully read directions on the fuel container; use only as directed. Use containers designed specifically for this purpose. Never use this stove for any purpose other than cooking.
-
Page 8: Fuel Recommendations
3. Fuel recommendations White Gasoline This stove is designed to burn white gasoline. Use only white gasoline fuel specifically for use in stoves. Automobile Gasoline Automobile gasoline contains additives that may result in poor performance of the stove. If it becomes necessary to use automobile gasoline, use only for a short period. -
Page 9: Description Of Components
Flat countersunk head screw M4 5. Description of Burner cap [Stove-unit] Carbon gasket components Wave plate Taper washer Taper washer Doughnut plate Spindle Spindle nut Needle Windscreen E-3 ring Flame control Pot support washer Pot support spring Pot support washer Pot support collar Pan- head... -
Page 10: Using The Gigapower Wg Stove
6. Using the GigaPower WG Stove Pour fuel into 6-1 Stove Assembly and Fuel Bottle. Preparation for Burning Refer to step 1. Install 6-1 Stove Assembly and pump unit. Preparation for Burning Refer to steps 2- 4. Pressurize 6-1 Stove Assembly and pump unit. -
Page 11: Stove Assembly And Preparation For Burning
6-1 Stove Assembly and Preparation for Burning Place the GigaPower WG Stove on a stable, level surface. Using the stove on an unstable surface is dangerous and may result in improper burning. 1. Pour white gasoline into the GigaPower fuel bottle. Do not fill beyond the Fill Level Line. - Page 12 4. Turn the Light/cook lever clockwise to the LIGHT position. Caution: If the stove is lighted in the COOK position (counterclockwise ) , excessive fuel will be injected into the unit resulting in an unstable flame. If the condition is not corrected, fuel may leak around the damper tube and spontaneously ignite.
-
Page 13: Lighting The Stove, Burning And Flame Control
8. Carefully join the other end of the fuel hose to the pump unit by turning the connector clockwise . Firmly tighten the connector by hand; DO NOT use any tools to tighten. If a tool is used to tighten, the threads may be damaged while in use. Caution: To prevent damage to the O-rings on the fuel hose, lightly apply maintenance grease from time-to-time. - Page 14 Caution: To prepare for lighting the stove, hold a heat source near the burner head . With the other hand, quickly open the main valve 2. Light the heat source and quickly turn the main valve knob counterclockwise until fully open. The fuel-air mixture will ignite when the heat source makes contact.
- Page 15 3. The burner flame becomes stabilized 15-20 seconds after lighting the stove. Turn the Light/ cook lever counterclockwise to the COOK position. Caution: The flame will not stabilize if the lever is turned counterclockwise to the COOK position prior to the initial stabilization.
-
Page 16: Extinguishing The Burner Flame
6-3 Extinguishing the burner flame 1. Turn the main valve knob fully clockwise to cut off the fuel supply. 2. Turn the flame control fully counterclockwise to open completely (maximum output position). 3. When the burner flame has been extinguished, turn the flame control fully clockwise. -
Page 17: Disassembly And Storage
6-4 Disassembly and Storage 1. Wait until the stove has sufficiently cooled down before proceeding with disassembly and storage. Caution: Stove is extremely hot after use. Use extreme caution to avoid burns. 2. NEVER disassemble or store the stove near a fire or an open flame. Caution: Do not disassemble or store this stove close to a fire or open flame. - Page 18 6. Firmly screw the bottle cap to the fuel bottle. Caution: Confirm that the seal gasket for the bottle cap is free from dust, dirt, and other foreign materials. If the cap cannot be installed smoothly, remove it and try again. Forcefully installing the bottle cap may result in damage to the threads in the bottle cap.
-
Page 19: Troubleshooting
If the fuel is not injected from the pump unit, the pump unit has been damaged and must be returned to the place of purchase or to Snow Peak. Connect the fuel hose to the pump unit. Open the main valve slightly;... - Page 20 Generator is clogged. If discharge of fuel-air mixture from the burner cannot be ensured, a clogged generator should be suspected. Replace with a new jet. 6. The stove does The atmospheric In cold weather (temperatures below freezing) not ignite even temperature is too low preheat the stove by applying a small amount though the fuel-air...
- Page 21 If the end cap is loose, tighten it firmly. If the the Light/cook fuel leak cannot be stopped, return the stove lever. to the place of purchase or to Snow Peak for repair. NEVER disassemble the Light/cook lever unit. 11. Fuel leak near...
-
Page 22: Maintenance
8. Maintenance When performing the maintenance measures below, please refer to the illustrations on page 9. 1. Cleaning the burner While cooking, the burner may become clogged from the overflowing liquids. Therefore, clean the burner on a regular basis. Procedure: Remove the flat countersunk head screw M4 located in the center of the burner. -
Page 23: Service And Warranty
9. Service and warranty Snow Peak products are designed to be reliable in the field and to provide many years of satisfaction. In the unlikely event that a product fails to function properly, contact the dealer where the product was purchased or Snow Peak Customer Service.
Need help?
Do you have a question about the GS-011 and is the answer not in the manual?
Questions and answers