Download
Share
Print this page
QSC K8.2 Mounting Quick Start Manual
  1. Manuals
  2. Brands
  3. QSC Manuals
  4. Speakers
  5. K8.2
  6. Mounting quick start manual

QSC K8.2 Mounting Quick Start Manual

K.2 series
Hide thumbs Also See for K8.2:
1
2
3
4
5

Advertisement

Quick Links

Download this manual See also: User Manual
K.2 Series
Yoke Mounting Quick Start Guide
The term "WARNING!" indicates instructions regarding personal safety. If the instructions are not followed the result may be
bodily injury or death.
The term "CAUTION!" indicates instructions regarding possible damage to physical equipment. If these instructions are not
followed, it may result in damage to the equipment that may not be covered under the warranty.
The term "IMPORTANT!" indicates instructions or information that are vital to the successful completion of the procedure.
The term "NOTE" is used to indicate additional useful information.
The intent of the lightning flash with arrowhead symbol in a triangle is to alert the user to the presence of un-
insulated "dangerous" voltage within the product's enclosure that may be of sufficient magnitude to constitute a
risk of electric shock to humans.
The intent of the exclamation point within an equilateral triangle is to alert the user to the presence of important
safety, and operating and maintenance instructions in this manual.
WARNRNG!: These mounting brackets shall only be used with K.2 Series loudspeakers. Use with other
apparatus could result in instability and possible injury.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Only use attachments/accessories specified by the manufacturer.
6. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any
way, or has been dropped.
7. Adhere to all applicable, local codes.
8. Consult a licensed, professional engineer when any doubt or questions arise regarding a physical
equipment installation.
9. Before placing or installing any loudspeaker product, inspect all hardware, cabinets, transducers, brackets and
associated equipment for damage. Any missing, corroded, deformed, or non-load rated component could
significantly reduce the strength of the installation and should be immediately corrected. Use only hardware which is
rated for the loading conditions of the installation and any possible short-term unexpected overloading. Never exceed
the rating of the hardware or equipment.
TD-000524-00-A
*TD-000524-00*
EXPLANATION OF SYMBOLS

IMPORTANT SAFETY INSTRUCTIONS

Advertisement

loading

Related Manuals for QSC K8.2

Summary of Contents for QSC K8.2

  • Page 1: Important Safety Instructions

    K.2 Series Yoke Mounting Quick Start Guide EXPLANATION OF SYMBOLS The term “WARNING!” indicates instructions regarding personal safety. If the instructions are not followed the result may be bodily injury or death. The term “CAUTION!” indicates instructions regarding possible damage to physical equipment. If these instructions are not followed, it may result in damage to the equipment that may not be covered under the warranty.

  • Page 2: Warranty

    Warranty For a copy of the QSC Limited Warranty, visit the QSC website at www.qsc.com Yoke Mounting the K.2 Series Loudspeakers WARNRNG!: Read and follow these instructions carefully. If the loudspeakers are not installed properly, they could fall, causing personal injury or death, and damage to the equipment.
  • Page 3 2. Install the flat washers (2) onto the bolts. 3. Thread the nuts (3) onto the bolts, then tighten. 4. Make sure that all bolts are tightened. (K8.2 - 2 bolts, K10.2 - 4 bolts, K 12.2 - 6 bolts) Install the Yoke WARNRNG!: Make sure that the installation adheres to all applicable code and regulations.
  • Page 4 RNOT!: The pole-cup adapter for the K10.2 and K12.2 is slightly different than the K8.2 shown in Figure 3. 3. Insert two M4 - 20 mm screws (1), removed earlier, through the pole-cup adapter (2).
  • Page 5 Toll free (USA only) © 2017 QSC, LLC. All rights reserved. QSC and the QSC logo are registered trademarks of QSC, LLC in the U.S. Patent and Trademark office and other countries. All other trademarks are the property of their respective owners.

This manual is also suitable for:

K10.2K12.2