XTA DPA SERIES Operator's Manual page 54

Page 54
Mode = USB Only: The USB socket on the front panel is active. Selecting this choice
will then ask for the following further information to be confirmed:
USB Speed: As the USB connection appears as a virtual COM port in remote
software, it still has an associated serial speed. Leave at the default of 11500. This is
not the actual USB serial data rate — it's the virtual COM port data rate!
RS485 Relay:
network for connection to further devices (other DPA amplifiers or XTA processors)
RS485 Speed: Only shown if RS485 Relay = ON: set RS485 baud rate
(recommended to use 115200 unless working with older DP224 and DP226 processors
in which case use 38400)
Remote ID Number: Set a device ID (still required even on Ethernet
connections). This must be unique to the connected unit — setting the same ID on
multiple units may cause comms problems for all devices.
R S485
SERIAL N O.
A ll vents on front and r ear of unit m ust not be obstructed.
Tous les passages sur avant et ar rière de l'unité ne doivent pas être obstr ués.
R S485
SERIAL N O.
A ll vents on front and r ear of unit m ust not be obstructed.
Tous les passages sur avant et ar rière de l'unité ne doivent pas être obstr ués.
R S485
SERIAL N O.
A ll vents on front and r ear of unit m ust not be obstructed.
Tous les passages sur avant et ar rière de l'unité ne doivent pas être obstr ués.
R S485
SERIAL N O.
A ll vents on front and r ear of unit m ust not be obstructed.
Tous les passages sur avant et ar rière de l'unité ne doivent pas être obstr ués.
x ta
DPA Series — DPA80/DPA100 Operating Instructions
Choose ON to relay all remote control data onto the RS485
USB to PC
This unit's interface set as:
Mode: USB Only
USB Speed: 115200
RS485 Relay: On
RS485 Speed: 115200
Remote ID Number: 1
G PIO PO R T CO NTR O L 1 - A U D IO NETWO R K - 2 A U X 4 A U X 3 A U X 2
1: 0V
2/3: IN 1& 2
4/5: O U T 1& 2
6: + 5V
1 2 3 4 5 6
CH. D CH. C OUTPUT
O U T O U T CO NNECTIO NS
D C B A
1+ D + C+ B + A +
1- D - C- B - A -
2+ D + B +
2- D - B -
G PIO PO R T CO NTR O L 1 - A U D IO NETWO R K - 2 A U X 4 A U X 3 A U X 2
1: 0V
2/3: IN 1& 2
4/5: O U T 1& 2
6: + 5V
1 2 3 4 5 6
CH. D CH. C OUTPUT
O U T O U T CO NNECTIO NS
D C B A
1+ D + C+ B + A +
1- D - C- B - A -
2+ D + B +
2- D - B -
G PIO PO R T CO NTR O L 1 - A U D IO NETWO R K - 2 A U X 4 A U X 3 A U X 2
1: 0V
2/3: IN 1& 2
4/5: O U T 1& 2
6: + 5V
1 2 3 4 5 6
CH. D CH. C OUTPUT
O U T O U T CO NNECTIO NS
D C B A
1+ D + C+ B + A +
1- D - C- B - A -
2+ D + B +
2- D - B -
G PIO PO R T CO NTR O L 1 - A U D IO NETWO R K - 2 A U X 4 A U X 3 A U X 2
1: 0V
2/3: IN 1& 2
4/5: O U T 1& 2
6: + 5V
1 2 3 4 5 6
CH. D CH. C OUTPUT
O U T O U T CO NNECTIO NS
D C B A
1+ D + C+ B + A +
1- D - C- B - A -
2+ D + B +
2- D - B -
#1
A U X 1
#1
CH. B CH. A
O U T O U T
SERIES
Class 3 Wir ing D ESIG NED A ND
on O utputs
MA NU FA CTU R ED
IN ENG LA ND B Y
A U X 1
#2
CH. B CH. A
O U T O U T
SERIES
Class 3 Wir ing D ESIG NED A ND
on O utputs MA NU FA CTU R ED
IN ENG LA ND B Y
A U X 1
#3
CH. B CH. A
O U T O U T
SERIES
Class 3 Wir ing D ESIG NED A ND
on O utputs MA NU FA CTU R ED
IN ENG LA ND B Y
A U X 1
#N
CH. B CH. A
O U T O U T
SERIES
Class 3 Wir ing
D ESIG NED A ND
on O utputs
MA NU FA CTU R ED
IN ENG LA ND B Y
Rear of First Unit
Connect RS485 to next unit
Rear of Next Unit
Connect RS485 to next unit...
This unit's interface is set as:
Mode: RS485 Only
RS485 Speed: 115200
Remote ID Number: 2
Rear of Next Unit
Connect RS485 to next unit...
This unit's interface is set as:
Mode: RS485 Only
RS485 Speed: 115200
Remote ID Number: 3
Rear of Last Unit
Connect RS485 to next unit...
This unit's interface is set as:
Mode: RS485 Only
RS485 Speed: 115200
Remote ID Number: N