Table of Contents
Advertisement
Quick Links
Trademarks
FOXWELL is trademark of Shenzhen Foxwell Technology Co., Ltd.
All other marks are trademarks or registered trademarks of their respective holders.
Copyright Information
© 2014 Shenzhen Foxwell Technology Co., Ltd.
All rights reserved.
Disclaimer
The information, specifications and illustrations in this manual are based on the latest information
available at the time of printing.
Foxwell reserves the right to make changes at any time without notice.
Visit our website at:
www.foxwelltech.com
For Technical Assistance, send us email at
support@foxwelltech.com
1
NT1001 TPMS Trigger Tool Manual_English_V1.01
Advertisement
Table of Contents
Related Manuals for Foxwell NT1001
Summary of Contents for Foxwell NT1001
- Page 1 Disclaimer The information, specifications and illustrations in this manual are based on the latest information available at the time of printing. Foxwell reserves the right to make changes at any time without notice. Visit our website at: www.foxwelltech.com For Technical Assistance, send us email at support@foxwelltech.com...
-
Page 2: One-Year Limited Warranty
The customer will be billed for any parts or labor charges not covered by this limited warranty. d) FOXWELL will repair the Product under the limited warranty within 30 days after receipt of the product. If FOXWELL cannot perform repairs covered under this limited warranty within 30 days,... - Page 3 OF THE PRODUCT OR ARISING FROM BREACH OF THE WARRANTY, BREACH OF CONTRACT, NEGLIGENCE, STRICT TORT, OR ANY OTHER LEGAL OR EQUITABLE THEORY, EVEN IF FOXWELL KNEW OF THE LIKELIHOOD OF SUCH DAMAGES. FOXWELL SHALL NOT BE LIABLE FOR DELAY IN RENDERING SERVICE UNDER THE LIMITED WARRANTY, OR LOSS OF USE DURING THE PERIOD THAT THE PRODUCT IS BEING REPAIRED.
-
Page 4: Safety Information
● Do not touch engine components that get very hot when an engine is running to avoid severe burns. NT1001 TPMS Trigger Tool Manual_English_V1.01... - Page 5 Block drive wheels before testing with engine running. Put the transmission in park (for ● automatic transmission) or neutral (for manual transmission). And never leave a running engine unattended. Do not wear jewelry or loose fitting clothing when working on engine. ● NT1001 TPMS Trigger Tool Manual_English_V1.01...
-
Page 6: Table Of Contents
4. 2 L ..........................17 ATEST 5 RKE & RF MONITOR ........................18 6 TPM AUDIT REPORT ........................19 7 SYSTEM SETUP ..........................19 7.1 S ........................20 ELECT ANGUAGE 7.2 C ........................20 ONFIGURE EEPER NT1001 TPMS Trigger Tool Manual_English_V1.01... - Page 7 7.9 C ......................24 ONFIGURE HEEL 8 TOOL INFORMATION ........................25 9 UPDATE ............................25 9.1 U TPMS T .................... 25 PDATE THE RIGGER 9.2 U ........................... 27 ANUAL 9.3 U ......................27 PDATE ETTINGS NT1001 TPMS Trigger Tool Manual_English_V1.01...
-
Page 8: Using This Manual
IMPORTANT indicates a situation which, if not avoided, may result in damage to the test equipment or vehicle. Example: IMPORTANT Do not soak keypad as water might find its way into the TPMS trigger tool. NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 9: Introduction
2.2 About NT1001 The NT1001 TPMS trigger tool is a universal TPM sensor decoder or activator. It accurately activates and decodes TPM sensors and displays the data or any faults. -
Page 10: Descriptions
2 USB Cable - provides connection between the TPMS trigger tool and a computer to upgrade the tool and charges the built-in battery. - contains user’s guide, update client and update files. Software CD 4 Magnet - triggers early TPMS sensors which need a magnet to activate. NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 11: Technical Specifications
1. Press the power switch to power on the tool, and the unit will display the Main Menu. 2. Hold the power switch for one 1 seconds and the release to power down the NT1001, and the “Bye Bye” message displays. The tool powers down automatically after a period of inactivity. -
Page 12: Charging Via Personal Computer With Usb Cable
Indicates the TPMS tool is sending signals to the tire sensor for activation and test. Indicates battery charging. Indicates One Wheel test mode is selected. Indicates ALL Wheels test mode is selected. Indicates magnet is required to activate TPMS sensor. NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 13: Tpms Activation
This section illustrates how to use the TPMS trigger tool to activate and decode TPM sensor data. The NT1001 is designed to activate all know TPM sensors and decode data including sensor ID, tire pressure, temperature, battery condition, and OE part number, and to warn of a wrong sensor installed, missing or faulty sensor, duplicate ID, and incorrect sensor mode. -
Page 14: Activation In All Wheel Mode
1. In all wheel mode, the solid spot flashes at the wheel to be tested. Depending on the sensor type, place the tool to the correct position to insure sensor activation and decode. Below is a chart illustrating how to correctly place the tool. NT1001 TPMS Trigger Tool Manual_English_V1.01... - Page 15 4. Depending on test results, one of the following possible scenarios may display. Sensor Type Illustration Description TPMS sensor was successfully activated and Successful decoded. The NT1001 emits a series of tones Sensor Read and displays pressure at wheel location. NT1001 TPMS Trigger Tool Manual_English_V1.01...
-
Page 16: Activation In One Wheel Mode
The search period expires without reading a Failed Sensor TPM. The NT1001 emits a single audible beep and displays “No sensor detected.” Repeat the Read test process to verify. A sensor with a duplicate ID has been read. The NT1001 emits three audible beep and Duplicate ID displays “Sensor ID duplicate.”... -
Page 17: Latest Test
1. Scroll with the UP/DOWN arrow keys to highlight Latest Test from the Main Menu and press the YES key to start. A message asking if the old recording to be cleared displays. Figure 4-10 Sample Latest Test Screen Figure 4-11 Sample Delete Data Screen NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 18: Rke & Rf Monitor
This section illustrates how to check RF Remote Keyless Entry (key FOB) with the trigger tool. The NT1001 tests 315MHz and 433MHz key fobs only, and checks only for a signal present. To test the check RF Remote Keyless Entry: 1. -
Page 19: Tpm Audit Report
6 TPM Audit Report The NT1001 is capable of presenting all of its stored TPM data in an HTML files when connected to a PC via an USB cable. To view the TPM audit report 1. Insert the small end of the USB cable to the USB port at the right side of the TPMS trigger tool and the large end to a computer. -
Page 20: Select Language
1. Scroll with the UP/DOWN arrow keys to highlight Beep Set from Setup menu and press the YES key. Figure 7-3 Sample Beep Setup Screen 2. Press the UP/DOWN arrow key select an item and press the YES key to save and return. NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 21: Configure Auto Power-Off Interval
7.4 Adjust Display Contrast Selecting Contrast opens a dialog box that allows you to adjust display contrast. To adjust display contrast 1. Use the UP/DOWN key to select Contrast from Setup screen and press the YES key. NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 22: Toggle Backlight On/Off
Selecting ID format opens a dialog box that allows you to set ID data to be displayed in hexadecimal or decimal format. To change the ID display format 1. Scroll with the arrow key to highlight ID Format from Setup menu and press the YES key. NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 23: Configure Pressure Unit
2. Press the UP/DOWN arrow key select an item and press the YES key to save and return. Figure 7-14 Sample Pressure Unit Selection Screen 7.8 Configure Temperature Unit Selecting Temperature Unit opens a screen that allows you to set the temperature unit Celsius or Fahrenheit degrees. To configure temperature unit NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 24: Configure Wheel Mode
YES key. Figure 7-17 Sample Wheel Test Mode Setup Screen 2. Press the UP/DOWN arrow key select an item and press the YES key to save and return. Figure 7-18 Sample Wheel Test Mode Selection Screen NT1001 TPMS Trigger Tool Manual_English_V1.01... -
Page 25: Tool Information
● Update tool settings 9.1 Update the TPMS Trigger Tool NT1001 is able to be updated to keep you stay current with the latest development of diagnosis. To update the TPMS Trigger Tool, you need following tools: ● NT1001 TPMS Trigger Tool ●... - Page 26 ● Update online: With internet connection, the tool NT Wonder automatically detects the software version of NT1001 and read the latest software version from the server. If any new diagnosis software found, it will automatically upgrade your NT1001. Otherwise a prompt of new version not detected displays.
-
Page 27: User Manual
Settings option opens a screen that allows you to set the language and style of the tool. Still, it offers the option for you to automatically check the update files from the server. To set up the update tool NT1001 TPMS Trigger Tool Manual_English_V1.01... - Page 28 3. Select the language and the style you want from the left to right column. 4. Select and tick the “Auto check for updates” on the bottom of the screen, then press Apply key to confirm. Figure 9-5 Sample User Manual Screen NT1001 TPMS Trigger Tool Manual_English_V1.01...