EDID Mode Coaxial Link Power HDBT Out EL-4KHDBT -TX-40-IRS EL-4KHDBT-RX-40-IRS Standard EDID Mode Coaxial IR RX IR TX Link Power RS-232 HDMI In HDMI Out HDBT Out Link Link EL-4KHDBT -TX-40-IRS LINK POWER Upgrade HDBT In EL-4KHDBT-RX-40-IRS Standard HDMI LINK...
HDBaseT/Cat5e/6/6a cabling with or in close parallel proximity to mains power cables. Do not substitute or use any other power supply other than the enclosed unit, or a ELAN approved replacement. Do not disassemble either the Transmitter or Receiver units for any reason. Doing so will void the manufacturer’s warranty.
EL-4KHDBT-TXRX-40-IRS USER MANUAL Introduction The ELAN line of HDBaseT products offers market leading features at an outstanding value. The EL-4KHDBT-RX-40-IRS and EL-4KHDBT-TX-40-IRS are industry leading 4K HDBaseT solutions, delivering HDMI with HDCP 2.2 support, bi-directional IR, RS-232, and PoH (PoE) up to lengths of 40m at 4K (70m at 1080p) over a single CAT cable.
EL-4KHDBT-RX-40-IRS EL-4KHDBT-TXRX-40-IRS Standard USER MANUAL LINK POWER Upgrade HDBT In Panel Description EL-4KHDBT-RX-40-IRS EL-4KHDBT-RX-40-IRS Standard HDMI LINK POWER LINK IR RX IR TX Upgrade HDBT In RS-232 HDMI Out HDMI LINK RS-232 / serial connector Standard / Upgrade mode switch...
RJ45 Wiring - T568B Understanding the signal status lights The ELAN extender solutions include status LED indicators on both the Transmitter and Receiver products to show all connections are active and to help diagnose possible problems. Understanding the status lights: Receiver: •...
EL-4KHDBT-TXRX-40-IRS USER MANUAL EDID Control EDID (Extended Display Identification Data) is a data structure that is used between a display and a source. This data is used by the source to find out what audio and video resolutions are supported by the display, from this information the source will discover what the best audio and video resolutions need to be outputted.
The ELAN range of HDBaseT products include multiple options for control and routing of IR. IMPORTANT: The ELAN HDMI Platinum, Matrix, & HDBaseT product lines output 5 volts to power an IR Receiver on the IR Input and include an EL-4KACC-IR-CAB, 3.5mm Mono to 3.5mm Stereo 5v to 12v IR converter cable. This cable is required when using 12v IR products from Xantech, Niles, and SpeakerCraft.
Page 8
EL-4KHDBT-TXRX-40-IRS USER MANUAL www.elanhomesystems.com...
• Storage temperature: -4°F to 140°F (-20°C to 60°C) Package Contents EL-4KHDBT-TXRX-40-IRS • 1 x EL-4KHDBT-TX-40-IRS • 1 x EL-4KHDBT-RX-40-IRS • 1 x 12V/2A DC power supply • 1 x 5v-to-12v IR Converter Cable (EL-4KACC-IR-CAB) • 2 x Mounting kits •...
EL-4KHDBT-TXRX-40-IRS USER MANUAL Certifications FCC Notice This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
Need help?
Do you have a question about the EL-4KHDBT-RX-40-IRS and is the answer not in the manual?
Questions and answers