Operating Instructions; Pulling Head Selection For Blind Fasteners - Cherry CHERRYMAX G746A Original Instructions Manual

TM-G746A Rev.: B DCR# 17-0231
Before using the tool:
• Read the tool manual instructions; before first using the tool.
• Read and comply to all safety instructions given in this document in addition to the general safety rules applicable
• Make sure the tool is connected to an air source operating within the recommended pressure range
• Before installing the permanent fasteners, make sure that the structure is properly clamped with temporary fasteners
• Make sure that the correct pulling head is selected for the fastener to be installed and that the tool is in good working condition
Installing Fasteners: Place the fastener into the prepared hole then place the pulling head over its stem and depress the trigger.

PULLING HEAD SELECTION FOR BLIND FASTENERS

•
The lists given below are for reference only; for more up to date and detailed information, please check on the Cherry
Aerospace webpage as following:
database for tool recommendations)
Fastener Type
®
CherryMAX Bulb
(CR3XXX)
Cherry SST
(CR6XXX)
®
CherryMAX AB
(CR4XXX)
®
MaxiBolt S
(CR7XXXS)
MBC L/C
(Lock Creator)
MBC
(No Lock Creator)
CherryLock "A"
(CR2X7X)
4
MS (CR9XXX)
NPR (CCR274,
CCR284)
SPR (CR1233)
Tacking Rivet
(CCR294, CCR304)
Notes:
1
Longer grips may require a second activation of the trigger.
2
Nominal and oversized diameters.
3
Alloy Steel and Monel only; no -6 diameter (3/17) Aluminum.
4
Serrated stems only.
5
This tool may be set-up to install other types and sizes of fasteners; see Tool Manual for details.
DATE: 3/21/17

OPERATING INSTRUCTIONS

CAUTION
Installation Tooling
Part Number
PH to use
H701B-456
5
H747-456
5
H753A-456
H781-456, H781A-456
H782
H701B-456
5
H747-456
5
H753A-456
H781-456, H781A-456
H782
H701B-456
5
H747-456
5
H753A-456
H781-456, H781A-456
H782
H701B-456
5
H747-456
5
H753A-456
H781-456, H781A-456
H782
H746-4MBC (0R 5MBC, 6MBC)
H747-3A
H955-3 (or -4, -5, -6)
H886-3 (or -4, -5, -6)
H747-3NPR, H902-3NPR
H902-4NPR
H9015-3C (or -4C, -5C, -6C)
H9040-4C (or -5C, -6C , -8C)
Federal Identification Code: 11815
Manuals(links to current tool manuals) and
Type Adapter
NONE
Straight
NONE
Right Angle NONE
NONE
Offset
NONE
NONE
Straight
NONE
Right Angle NONE
NONE
Offset
NONE
NONE
Straight
NONE
Right Angle NONE
NONE
Offset
NONE
NONE
Straight
NONE
Right Angle NONE
NONE
Offset
NONE
Straight None
NONE
Straight
NONE
Right Angle NONE
NONE
NONE
704A9
Straight
704A6
5
© 2017 Cherry Aerospace
Product Expert (interactive
Rivet Diameters
Max. Grip
2
All
-4, -5 & -6
2
All
-4, -5 & -6
2
All
-4, -5 & -6
2
All
-4, -5 & -6
2
All
-4, -5 & -6
2 1
-4, -5 & -6 -09
2,3 1
-4, -5 & -6 -09
2,3
-04
-4, -5 & -6
2,3 1
-4, -5 & -6 -07
2,3 1
-4, -5 & -6 -07
-4 only All
-4 only All
-4 only All
-4 only All
-4 only All
-4, -5 & -6 -042
-4, -5 & -6 -042
-4, -5 & -6 -04
-4, -5 & -6 -042
-4, -5 & -6 -042
-4, -5 OR -6 -042
-3 ONLY -042
3
-042
-3, -4 & -5
3
-04
-3, -4 & -5
-3 DIA. ONLY All
-4 DIA. ONLY All
-3, -4, -5 & -6 All
-4, -5, -6 & -8 All
1