Connecting The Vcr - Sony SLV-SE70 Service Manual

Step 2 : Setting up the remote commander (continued)
Code numbers of controllable TVs
If more than one code number is listed, try entering them one at a time until
you find the one that works with your TV.
To make wide mode settings, see the footnotes below this table for the
applicable code numbers.
Manufacturer Code number
Sony 1 , 02
01*
Akai 68
Ferguson 52
1 1
Grundig 10* , 11*
Hitachi 24
JVC 33
Loewe 45
Mivar 09, 70
NEC 66
3
Nokia 15, 16, 69*
1
* Press WIDE to switch the wide picture mode on or off.
2 Press WIDE, then press Á +/– to select the wide picture mode you want.
*
3
* Press WIDE. The menu appears on the TV screen. Then, press >/./?// to
select the wide picture you want and press OK.
Notes
• If the TV uses a different remote control system from the one programmed to work
with the VCR, you cannot control your TV with the remote commander.
• If you enter a new code number, the code number previously entered will be erased.
• When you replace the batteries of the remote commander, the code number may
change. Set the appropriate code number every time you replace the batteries.
8
Getting Started
Step 3 : Connecting the VCR (continued)
3
Connect LINE-1 (TV) on the VCR and
the EURO-AV (Scart) connector on the
TV with the supplied EURO-AV cable.
This connection improves picture and
sound quality. Whenever you want to
watch the VCR picture, press
... TV/VIDEO to display the VIDEO
indicator in the display window.
4
Connect the mains lead to the mains.
If the mains plug does not fit in the mains, use the supplied plug
adapter.
Note
• If the TV is connected to the LINE-1 (TV) connector, setting the RF MODULATOR in
the OPTIONS-2 menu to OFF is recommended. In the OFF position, only the signal
from the aerial is output through the AERIAL OUT connector (see page 67). You do
not have to tune your TV to the VCR. Skip "Tuning your TV to the VCR" on page
15.
About the SMARTLINK features
If the connected TV complies with
1
SMARTLINK, MEGALOGIC* , EASYLINK*
3 4,
Q-Link* or EURO VIEW LINK* you can use
the SMARTLINK function after you complete
the steps on the previous page (the SMARTLINK indicator appears in the VCR's
display window when you turn on the TV). You can enjoy the following
SMARTLINK features.
• Preset Download
You can download your TV tuner preset data to this VCR and tune the VCR
according to that data in Auto Set Up. This greatly simplifies the Auto Set Up
procedure. Be careful, not to disconnect the cables or exit the Auto Set Up function
during the procedure.
See "Setting up the VCR with the Auto Set Up function" on page 14.
10
Getting Started
Code number
Manufacturer
Panasonic 17* 1 , 49
06* 1 , 07* 1 , 08* 1
Philips
12, 13
Saba
22, 23
Samsung
25
Sanyo
29
Sharp
36
Telefunken
43* 2
Thomson
38
Toshiba
SMARTLINK
2
,
Step 3

Connecting the VCR

If your TV does not have a EURO-AV connector, see page 12.
If your TV has a EURO-AV (Scart) connector
: LINE-1
(TV)
Mains lead
to mains
Aerial cable (supplied)
: Signal flow
EURO-AV cable (supplied)
1
Disconnect the aerial cable from your
TV and connect it to AERIAL IN on the
rear panel of the VCR.
2
Connect AERIAL OUT of the VCR and
the aerial input of your TV using the
supplied aerial cable.
• TV Direct Rec
You can easily record what you are watching on the TV (other than tapes being
played on this VCR). For details, see "Recording what you are watching on the TV
(TV Direct Rec)" on page 40.
• One Touch Play
With One Touch Play, you can start playback automatically without turning on the
TV. For details, see "Starting playback automatically with one button (One Touch
Play)" on page 36.
• One Touch Menu
You can turn on the VCR and TV, set the TV to the video channel, and display the
VCR's on-screen display automatically by pressing MENU on the remote
commander.
• One Touch Timer
You can turn on the VCR and TV, set the TV to the video channel, and display the
timer recording menu (the TIMER METHOD menu, the TIMER menu, or the
VIDEO PLUS+ menu) automatically by pressing
commander.
You can set which timer recording menu is displayed using TIMER OPTIONS in the
OPTIONS-2 menu (see page 67).
* 1 "MEGALOGIC" is a registered trademark of Grundig Corporation.
* 2 "EASYLINK" is a trademark of Philips Corporation.
* 3 "Q-Link" is a trademark of Panasonic Corporation.
* 4 "EURO VIEW LINK" is a trademark of Toshiba Corporation.
Note
• Not all the TVs respond to the functions above.
1-2
AERIAL IN
AERIAL OUT
AERIAL IN
EURO-AV
(Scart)
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
AERIAL
ANTENNE
IN
ENTREE
OUT
SORTIE
continued
9
Getting Started
TIMER on the remote
continued
11
Getting Started