Advertisement
--€
iilL
NiJ'
iiiiB,_,
g2
,,
(ARBON
MONOXIDE
POISONING
HAZARD
Failure
to fbllow
this warning
could result
in personal
injury
or death.
(asing
hole filler
cap iTnist be installed
in blower
shelf
hole
when
condensate
trap
is relocated
to prevent
combustion
products
being
drawn
in from
appliances
in the equipment
root11.
4. Install
condensate
trap into desired
casing
hole by inserting
tube connection
stubs
through
casing
hole and rotating
until
tabs snap into locking
position.
5. Fill unused
condensate
trap casing
holes
with
plastic
filler
caps (fhctory=supplied
in loose parts bag)
CONDENSATE
TRAP
TUBING
NOTE:
See Fig S or 9 or robe routing
label on main furnace
door
to check
fbr proper
connections.
1. (ollector
Box Drain Tube
a. Remove
£tctory=installed
plug flora LOWER
collector
box
drain robe (blue
and white
striped
label).
b. Install
removed
clamp and plug into UPPER
collector
box
&ain robe (blue label) which
was connected
to condensate
t_ap,
c. Connect
LOWER
collector
box drain
connection
to con=
densate
trap.
(i.)
(ondensate
Trap Located
on Left Side of (asing
Ca.) Connect
LOWER
collector
box &ain
robe (blue
and white
striped
label) to condensate
trap. Tube
does not need to be cut.
(b.) Clamp
tube to prevent
any condensate
leakage.
(20
(ondensate
Trap Located
on Right
Side of (asing
(a.) Install
drain
robe
coupling
(fhctory=supplied
in
loose
parts
bag)
into
collector
box
drain
robe
(blue
and white
striped
label)
which
was previ-
ously
plugged.
(b)
(onnect
larger
diameter
drain
robe
(factoo-
supplied
in loose
parts
bag)
to drain
tube
cou-
pling,
extending
collector
box
drain
robe
fbr
connection
to condensate
trap
(c.) Route
extended
collector
box drain
robe directly
fi'om
collector
box
drain
to condensate
txap as
shown
in Fig
9
(d)
Determine
appropriate
length
and cut
(e.) (onnect
to condensate
trap.
(f)
Clamp
tube to prevent
any condensate
leakage.
2
Inducer
Housing
Drain
Tube
a
Remove
_tctory=installed
cap
and clamp
fi'om
LOWER
inducer
housing
drain connection.
b
Remove
and discard
UPPER
(molded)
inducer
housing
&ain robe which
was previously
connected
to condensate
trap.
c
Install
cap and clamp
on UPPER
inducer
housing
drain
connection
where
molded
&ain robe was removed.
d
Use inducer
housing
&ain tube (violet
label
and factow-
supplied
in loose parts
bag)
to connect
LOWER
inducer
housing
drain
connection
to the condensate
tlap.
e. Connect
inducer
housing
drain
connection
to condensate
trap.
(1.) (ondensate
Trap Located
on Left Side of (asing
AUXILIARY
CONDENSATE
TRAP
PLUG i_
CAP
'9" BOX --,
_
COLLECTOR BOX
DRAIN TUBE
(BLUE AND WHITE STRIPED)
O
O
_
COLLECTOR
BOX
X
TUBE (GREEN)
_INDUCER
HOUSING
X
DRAIN TUBE (VIOLET)
BOX EXTENSION
,\
DRAIN TUBE
\_-"
COLLECTOR BOX
DRAIN TUBE (BLUE)
COLLECTOR BOX -
xX
EXTENSION TUBE
_X
DRAIN TUBE COUPLING _
X_
x
COLLECTOR BOX TUBE (PINK)
RELOCATE TUBE BETWEEN BLOWER SHELF AND INDUCER HOUSING FOR
040,060, AND 080 HEATING INPUT FURNACES
Fig. 10--Horizonta{
Left Tube Configuration
A00215
Advertisement
