Page 1
Installation of the event recorder is not complicated, but care must be taken to ensure successful operation. Follow these instructions carefully to ensure proper orientation and operation. Check the contents of the installation kits Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 2
Step 2 Using the alcohol prep pad provided, thoroughly clean the mounting area. Step 3 Using a clean, dry cloth, thoroughly dry the mounting area. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 3
Step 3 Position the assembly behind the mirror, about one inch to the right of the post to allow easy access to the Torx screw and power connection. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 4
Remove the event recorder from the mounting bracket. Step 4 Check the fit of the bracket against the windshield. If the windshield is curved, gently bend the bracket so that it will lie flush against the glass. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 5
You may need to (carefully) apply additional pressure to the bracket and remove any large air bubbles. Use a small pin to create an escape path for the air if the problem is persistent. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 6
You may need to remove the trim to route the cable. When reinstalling, be careful not to damage the trim clips or the cable. Keep the cable clear from sharp edges and moving parts. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 7
Interconnect cable so that it cannot be unplugged by the driver. The plastic washers can be easily removed from the metal bracket after removing the screws. Make sure the larger of the two washers is on the left (power connection) side of the bracket. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 8
Wiring Diagram (DC3 with SEM Installation) The RJ45 Interconnect Cable is 14 feet long with RJ45 (large) connectors at each end. One end of the cable plugs into the event recorder. It is then routed to a secure location under the dashboard and plugged into the middle port of the Cable Access Terminal (CAT).
Page 9
Plug the UM05 Interconnect Cable into the Universal Module (UM05). Step 3 Plug the UM05 Switch Cable into the Universal Module (UM05). Do not secure the CAT or UM05 permanently in place until after the connections have been tested. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 10
RED WIRE to a 12V or 24V fused power source that is ALWAYS ON. Step 3 Connect the BROWN WIRE to a 12V or 24V fused power source that is IGNITION–SWITCHED. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 11
Step 3 Use a voltmeter to measure the voltage at either of the bulb terminals. Step 4 Turn the load “ON” (i.e. open a door to turn on the dome light). Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 12
Make sure you are connecting to the correct side of the dome light circuit as measured in step 5. Wait until after you have tested the primary trigger on page 16 before finalizing the connections. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 13
The connection must be made to the terminal that changed voltage. Step 5 Connect the orange wire to the switch. Make sure you are connecting to the correct side of the switch circuit as measured in step 4. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 14
The LED on the left of the lens will light (solid green) for about 30 seconds after power is first applied. If the left LED does not turn off or if it begins flashing (either red or green), please call DriveCam Technical Support for instructions.
Page 15
* * * The six red lights must go out when the key is in the OFF position * * * * * * The single (red or green) LED to the right of the lens will always remain lit * * * Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 16
If the UM05 Test Light did not light at all, check the power, ground, & primary wire connections. Make sure the connection was made to the correct side of the circuit as described on page 12. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 17
If the UM05 Test Light did not light at all, check the power, ground, secondary wire, & switch connections. Make sure the connection was made to the correct side of the circuit as described on page 13. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 18
Finalizing Connections This completes installation of the DriveCam Event Recorder and the primary and secondary triggers of the UM05 device. If you are planning to use the output feature of the UM05, proceed to the next page to continue with the installation.
Page 19
The DriveCam Event Recorder has the ability to control other devices within the vehicle. The event recorder has an output signal that will change from its normal state whenever an event is triggered. After saving that event, the output returns to its normal state.
Page 20
If the OUT switch on the UM05 is set to NORM LO, the output switch will be open all the time unless an event has been triggered in the DriveCam Event Recorder. When an event is triggered, the output switch will close for about 1 second.
Page 21
GPS and other electronic devices with signal inputs require very little current so the voltage supplied to them by the blue wire will be very close to the voltage supplied to the yellow wire. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 22
To turn the device ON we need the UM05 switch to turn ON which will make the voltage at the blue wire go LOW. Table 2 shows how to set the UM05 OUT switch to achieve the desired function at the load. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 23
First, the current through the resistor must be 2 Amps or less. For a 12 Volt electrical system this means the resistor should be greater than 8 Ohms. To prevent other problems, the resistor value should be as high as possible and still pass the current needed for the application. Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
Page 24
I < 2 Amps At Least 8 Ohms (12V) Yellow Wire (No Connection) 1,800 Ohms 1/2 Watt Blue Wire Input UM05 Control Black Wire (Always Connected to Ground) Ground IGURE ROVIDING XTRA RIVE URRENT Page DRC 242-A 2007-08-03 DC3 with SEM Installation Instructions...
How does the event recorder work? The DriveCam Event Recorder is mounted on the windshield behind the rearview mirror and captures sights and sounds inside and outside the vehicle. The forward facing lens (outside view) captures the viewing area in the front of the vehicle. The inside lens captures what is happening inside the vehicle plus whatever is visible through the side and rear windows.
Page 26
Contact DriveCam Technical Support. Both LEDs blinking Both LEDs blinking Internal error. red alternating red alternating Contact DriveCam Technical Support. Copyright 2007 DriveCam, Inc. All rights reserved. DriveCam Technical Support is available 24 hours / 7 days at (866) 910-0403.
Page 27
Security screws used to seal unit: Full coverage Block to prevent power disconnection: Memory format: Disk on chip (non-removable) Mounting bracket: Non-removable Copyright 2007 DriveCam Inc. All rights reserved. DriveCam Technical Support is available 24 hours / 7 days at (866) 910-0403.
Need help?
Do you have a question about the DC3 and is the answer not in the manual?
Questions and answers