Download Print this page

Advertisement

CAUTION:
Before servicing this chassis, it is important that the service technician read the "Safety
Precautions" and "Product Safety Notices" in this service manual.
ATTENTION:
Avant d'effectuer l'entretien du châassis, le technicien doit lire les «Précautions de sécurité"
et les «Notices de sécurité du produit" présentés dans le présent manuel.
VORSICHT:
Vor Öffnen des Gehäuses hat der Service-Ingenieur die „Sicherheitshinweise" und „Hinweise
zur Produktsicherheit" in diesem Wartungshandbuch zu lesen.
SPECIFICATIONS AND PARTS ARE SUBJECT TO CHANGE FOR IMPROVEMENT
SERVICE MANUAL
MANUEL D'ENTRETIEN
WARTUNGSHANDBUCH
Colour Television
December 2003
No. 0202
17LD4200
"
Data
contained
within
this
manual is subject to alteration for
improvement.
Les données fournies dans le présent
manuel d'entretien peuvent faire l'objet
de modifications en vue de perfectionner
le produit.
Die
in
diesem
Wartungshandbuch
enthaltenen Spezifikationen können sich
zwecks Verbesserungen ändern.
Service

Advertisement

   Also See for Hitachi 17LD4200

   Summary of Contents for Hitachi 17LD4200

  • Page 1

    No. 0202 17LD4200 » SERVICE MANUAL MANUEL D'ENTRETIEN WARTUNGSHANDBUCH CAUTION: Before servicing this chassis, it is important that the service technician read the “Safety Precautions” and “Product Safety Notices” in this service manual. Data contained within this Service manual is subject to alteration for improvement.

  • Page 2: Table Of Contents

    17LD4200 TFT LCD TV 1 SCOPE ............................4 1.1 PRODUCT FEATURES .....................4 1.2 MAIN DIMENSIONS / WEIGHT ..................4 1.3 LOADING QUANTITY.....................4 1.4 NICAM ..........................4 2 ELECTRICAL PERFORMANCE..................5 2.1 STANDARD TESTING CONDITIONS ................5 2.2 VIDEO SIGNALS ......................5 2.3 DDC SIGNALS (VESA DDC1/2B) ...................9 2.4 DIGITAL CONTROL OPERATION..................9...

  • Page 3

    8 MECHANICAL REQUIREMENTS..................41 8.1 VIBRATION AND SHOCK .....................41 8.2 PACKAGE DROP SPECIFICATION ................42 8.3 DIMENSION SIZE AND WEIGHT.................42 8.4 GAP SPEC........................43 8.5 PLASTIC MATERIAL .....................46 8.6 GAP SPEC........................46 9 Block............................47 9.1 MAIN BOARD BLOCK DIAGRAM ................47 9.2 TUNER BOARD BLOCK DIAGRAM................48 10 Connect .............................49 10.1 PCBA CONNECTOR LOCATION ...................49 10.2 CONNECTOR P/N ASSIGNMENT .................51...

  • Page 4: Scope

    1 SCOPE This short specification describes the electrical, optical and functional performance requirements for a 43.1cm (17”) TFT LCD color TV monitor with VGA/CVBS/S-Video/COMPONENT/TV compatible interface. 1.1 PRODUCT FEATURES • 43.1 cm (17”) a-si TFT Active matrix LCD panel, 0.289 mm dot pitch, 262.144 colors. •...

  • Page 5: Electrical Performance

    2 ELECTRICAL PERFORMANCE All tests must be performed under “standard testing conditions” (item 2.1) unless otherwise specified 2.1 STANDARD TESTING CONDITIONS - Warm up time : >30 min. - AC supply voltage : 110V or 230V± 5%, 50± 3 Hz : 20°C ±...

  • Page 6

    2.2.2 ANALOG RGB SYNC INPUTS Level: L = 0V ~ 0.8V H = 2.4V ~ 5V Separate sync. Polarity: positive or negative The Monitor has to operate up to the following specified TTL-input signals: < 200ns < 0 7V 2 4V 2 4V 0 8V 0 8V...

  • Page 7

    2.2.4 ANALOG RGB SIGNAL TIMING VESA MODES Horizontal Vertical Nominal Sync Nominal Sync Nominal Frequency Polarity Freq. Polarity Pixel Mode Resolution Total (KHz) (Hz) Clock (MHz) 640x480@60Hz 800 x 525 31.469 59.940 25.175 640x480@72Hz 832 x 520 37.861 72.809 31.500 640x480@75Hz 840 x 500 37.500...

  • Page 8

    2.2.6 PAL TV INPUTS Tuner Model Name : FI/FQ1216 : PHILIPS Receiving System : PAL Channel System : Air / Cable : VHF Low : 48.25MHz ~ 160.00MHz : VHF High : 160.00MHz ~ 442.00MHz : UHF : 442.00MHz ~ 863.25MHz IF Frequency : PIF : 38.90MHz...

  • Page 9: Ddc Signals (vesa Ddc1/2b)

    2.3 DDC SIGNALS (VESA DDC1/2B) This monitor is equipped with VESA DDC 1/2B according to VESA DISPLAY DATA CHANNEL STANDARD V. 1.0 Rev.1 (tt.mm.199j) It transmits the EDID-file as a continuous data stream, clocked by V-SYNC (DDC 1); the controller may increase the Vert. frequency to 25 kHz max. for improved transmission rate. As an alternative, it sends the EDID-file upon request by the host-system (Read EDID, Device A0h Start address 00h) in an I C compatible format (DDC 2).

  • Page 10: Power Supply

    2.5 POWER SUPPLY 2.5.1 FEATURES A/C Line voltage range : 100 V ~ 240 V : 50 ± 3Hz, 60 ± 3Hz A/C Line frequency range Current : 1.5A max. at 90V, 0.75A max. at 265V Peak surge current : < 50A peak at 220 VAC, : < 30A peak at 110 VAC and cold starting Leakage current : <...

  • Page 11

    2.5.4 INVERTER SPECIFICATION 2.5.4.1 Electrical Characteristics: Item Condition Typ. Max. Unit Input Voltage Vin -5% / +15% 11.4 12.6 Input Current Vin=12V±5% Vbri=3.3V Input Power Vin=12V±5% Vbri=3.3V Inrush current Irush Vin –5% ,under 14 TBD A times of rating current of Fuse Output Voltage Vout Vin=12V, Vbri =1.8V...

  • Page 12

    2.5.4.2 Fuse rating: 2.5.4.2.1 Rating current is under 60% of rating current decreasing curve of fuse at maximum ambient temperature. 2.5.4.2.2 Inrush current Fuse vender guarantee 100,000 cycles. Rush current is under 14 times of rating current of Fuse. IΛ2t is under 25% of vender's I2t-T curve. 2.5.4.3 Functional Pin Description: 2.5.4.3.1...

  • Page 13

    Ripple Vripple Item 1, 2, 3 condition mVpp Noise Vnoise Item 1, 2, 3 condition mVpp...

  • Page 14: Connectors / Controls

    2.5.5.2 Functional Pin Description: Input Connector: SCD437CCS DIA:2.0mm Pin No. Symbol Description +12V Ground 2.6 CONNECTORS / CONTROLS 2.6.1 CONNECTORS : Φ2.5mm DC Jack Power : Monitor rear side Analog RGB : Monitor rear side / Data Cable : 15-pin D-sub female / male Pin –...

  • Page 15

    2.6.4 MONITOR CONTROL FUNCTION PC mode Bright, Contrast, Picture position, OSD position, Auto adjustment, Clock, Phase, OSD Transparence, Language, Color Temperature Graphic/Text select VIDEO mode AUDIO , PICTURE , SETUP TV mode AUDIO , PICTURE , SETUP , SYSTEM 2.6.5 OSD Pattern PC mode...

  • Page 16

    Video, TV mode...

  • Page 17: Testing Conditions

    2.7 TESTING CONDITIONS Pattern Checking Circle Overall Linearity , Geometry On a black background is suited for checking the Framing. overall linearity and geometry Reflections aspect ratio format The white circle changes automatically to black when used with the white pattern and is useful for checking reflection.

  • Page 18: Osd Function

    2.8 OSD FUNCTION 2.8.1 IR Control POWER TEXT Switch between power-on and Turn the Teletext function power-off. ON/OFF MUTE INDEX Turn the sound on/off. Turn page to index page. MODE Select the language and the sound Turn ON/OFF list mode. output VOLUME REVEAL...

  • Page 19

    2.8.1.1 Teletext Teletext is an optional function, therefore only the set of the teletext system can receive the teletext broadcast. Teletext is a free service broadcast by most TV stations which gives up-to-the-minute information on news, weather, television programs, stock prices and many other topics. The teletext decoder of this TV can support the SIMPLE, TOP and FASTEXT systems.

  • Page 20: Advanced Setting

    Page selection 1. Press the “INDEX ” button to select the index page. 2. You can select the pages which are color coded along the bottom line with the same colored buttons. 3. Corresponding to the SIMPLE teletext mode, you can select a page by entering its three-digit page number with the NUMNER buttons in FASTEXT mode.

  • Page 21

    BALANCE 1.Press "MENU" (on main body) or "►" (on remote control) button. 2.Press " " (on main body) or "↑, ↓" (on remote control) button to select BALANCE. 3.Adjust the speaker balance on Left/Right by pressing " " (on main body) or "←, →" (on remote control) button.

  • Page 22

    SETUP CH. SEARCH Press "MENU" (on main body) or "►" (on remote control) button. Press " " (on main body) or "→" (on remote control) button to select SETUP. Press " " (on main body) or "↑, ↓" (on remote control) button to select CH.

  • Page 23

    RECALL Press “MENU” (on main body) or “►” (on remote control) button. Press “ “ (on main body) or “→” (on remote control) button to select SETUP. Press “ “ (on main body) or “↑, ↓” (on remote control) button to select RECALL. Press “...

  • Page 24

    SYSTEM Please make sure the SYSTEM menu is ON status before selecting it. (Please refer to above SYSTEM- OFF ON setting in the SETUP menu.) PAL/SECAM/SECAM L 1.Press "MENU" (on main body) or "►" (on remote control) button. 2.Press " "...

  • Page 25: Visual Performance

    3 VISUAL PERFORMANCE 3.1 MEASUREMENT CONDITIONS Warm up time: 30min. Angle for measurement: 90°H and V Distance: 100cm Equipment: Minolta CS-100 Measurement positions: Grey scale definition: White means digital value for RGB=255,255,255 50% gray, RGB=127,127,127 Black, RGB=0,0,0 3.2 PICTURE SIZE AND CENTERING For 1280 X 768 resolution the picture size is equal to the active area of the display.

  • Page 26: Brightness Uniformity

    768 resolution Resolution, for XGA, SVGA, VGA Text and VGA Graphics the conditions of 3.2 can be met. 3.2.2 POSITION CONTROL RANGE The picture position can be adjusted that a complete picture can be displayed centered 3.2.3 Max. BRIGHTNESS : PC Mode 340(MIN.), 400(Typ.) cd/m2 Test conditions: - center of display (5)

  • Page 28: White Color Uniformity

    3.5 WHITE COLOR UNIFORMITY The deviation of the white color coordinates at the 4 positions (1)….(4) should not exceed ± 0.020 with respect to the measurement at the center position(5). 3.6 PURITY Purity is defined as the uniformity of the chromaticity of the three primary colors. The Deviation of the color coordinates of the primary colors red/green/blue at the 4 positions (1)…(4) should not exceed ±...

  • Page 29

    Ambient Temperature ﹕ 25℃± 5℃ 4.1.3 Warm up Time ﹕ minimum 10 minutes after power on and audio signal input 4.1.4 Test Distance ﹕ 50cm from monitor screen and at the center of left and right speaker 4.1.5 Output Impedance ﹕ 4.5 ohm ± 15% 4.1.6 4.1.7 Output Voltage ﹕...

  • Page 30: Amplifier Characteristic

    4.2 AMPLIFIER CHARACTERISTIC 4.2.1 Output Power ( Unit : Watt) 1). Effective Output ﹕ 2.5 Watts ( measure at the output voltage of 1% Distortion Factor) 2). Maximum Output ﹕ 3 Watts (measure at the output voltage of 20% Distortion Factor) 3).

  • Page 31: Tuner Electrical Performance

    5 TUNER Electrical Performance 5.1.1 Receiving System : ( PAL STANDARD SYSTEM ) Channel Low BAND : 48.25MHz ~ 160.00 MHz High BAND : 160.00MHz ~ 442.00 MHz BAND : 442.00MHz ~863.25 MHz Intermediate Frequency PIF : ( 38.90 )MHz CIF : ( 34.47 )MHz SIF : B/G: 33.40 MHz : 33.16 MHz...

  • Page 32

    PAL B/G Air Channel Channel Frequency Channel Frequency (Mhz) (Mhz) 48.25 687.25 55.25 695.25 62.25 703.25 175.25 711.25 182.25 719.25 189.25 727.25 196.25 735.25 203.25 743.25 210.25 751.25 217.25 759.25 224.25 767.25 471.25 775.25 479.25 783.25 487.25 791.25 495.25 799.25 503.25 807.25 511.25...

  • Page 33

    PAL B/G Cable Channel Channel Frequency Channel Frequency Channel Frequency (Mhz) (Mhz) (Mhz) 48.25 311.25 607.25 55.25 319.25 615.25 62.25 327.25 623.25 69.25 335.25 631.25 76.25 343.25 639.25 83.25 351.25 647.25 90.25 359.25 655.25 97.25 367.25 663.25 105.25 375.25 671.25 112.25 383.25 679.25...

  • Page 34

    PAL D/K Air Channel Channel Frequency Channel Frequency (Mhz) (Mhz) 49.75 711.25 57.25 719.25 65.75 727.25 77.25 735.25 85.25 743.25 168.25 751.25 176.25 759.25 184.25 767.25 192.25 775.25 200.25 783.25 208.25 791.25 216.25 799.25 471.25 807.25 479.25 815.25 487.25 823.25 495.25 831.25 503.25...

  • Page 35

    (4) PAL D/K Cable Channel Channel Frequency Channel Frequency Channel Frequency (Mhz) (Mhz) (Mhz) 49.75 368.25 671.25 57.75 376.25 679.25 65.75 384.25 687.25 77.25 392.25 695.25 85.25 400.25 703.25 112.25 408.35 711.25 120.25 416.25 719.25 128.25 424.25 727.25 136.25 432.25 735.25 144.25 440.25...

  • Page 36

    (5) PAL I Air Channel Channel Frequency Channel Frequency (Mhz) (Mhz) 45.75 695.25 53.75 703.25 61.75 711.25 175.25 719.25 183.25 727.25 191.25 735.25 199.25 743.25 207.25 751.25 215.25 759.25 471.25 767.25 479.25 775.25 487.25 783.25 495.25 791.25 503.25 799.25 511.25 807.25 519.25 815.25...

  • Page 37

    PAL I Cable Channel Channel Frequency Channel Frequency Channel Frequency (Mhz) (Mhz) (Mhz) 45.75 319.25 623.25 53.75 327.25 631.25 61.75 335.25 639.25 69.25 343.25 647.25 76.25 351.25 655.25 83.25 359.25 663.25 90.25 367.25 671.25 97.25 375.25 679.25 105.25 383.25 687.25 112.25 391.25 695.25...

  • Page 38

    SECAM L´ Air Channel Channel Frequency Channel Frequeny (Mhz) (Mhz) 47.75 695.25 55.75 60.5 703.25 63.75 711.25 719.25 727.25 735.25 471.25 743.25 479.25 751.25 487.25 495.25 759.25 503.25 511.25 767.25 519.25 775.25 527.25 535.25 783.25 543.25 551.25 791.25 559.25 799.25 567.25 575.25 807.25...

  • Page 39: Accessories

    6 ACCESSORIES 6.1 POWER CABLE Length : 1.8m + 5cm/-5cm Color : black Connectors : Monitor–side / Mains-side : IEC 320-1 / CEE7-VII (EU) : IEC 320-1 / BS-1363 (UK) 6.2 EXTERNAL ADAPTER Type : Worldwide type Length of DC cable : 1.5m + 1.5cm/-0cm Color of adapter : black...

  • Page 40: Environmental

    7 ENVIRONMENTAL 7.1 ENVIRONMENTAL CONDITIONS (CLIMATIC) Operation (according to IEC 721 / EN 60721 Class 3K3) : (unpacked for a long time) Temperature +5°C ~ + 40°C Humidity 20% ~ 85% Max. Dew Point Temperature +27°C Max. abs. Air Humidity 25 g/m Max.

  • Page 41: Environmental Condition (mechanical)

    7.2 ENVIRONMENTAL CONDITION (MECHANICAL) Storage and Transport: (according to IEC 721 / EN 60721 class 2M2) Test Procedure IEC 68/EN 60068 Vibration Freq. range 5~10 10~100 100~500 (random vibration) Change db/oct Spectral IEC 68-2-64 acceleration 0.75 EN 60068-2-64 density Accel. RMS 11.4 Axis Duration/Axis...

  • Page 42: Package Drop Specification

    8.2 PACKAGE DROP SPECIFICATION Listed below are standards of drop heights for monitor product Product Weight height Specs <9.1 kg 0.91 m 9.2~18.2 kg 0.76 m 18.3~27.2 Kg 0.61 m 27.3~45.4 Kg 0.46 m 8.2.1 Drop Test Sequence Drop Order Drop point Drop Times Right Front Bottom Corner...

  • Page 43: Gap Spec

    8.4 GAP SPEC. 8.4.1 The step between front bezel and back cover shall be within specification. Back Cover & Bezel Gap Neck Front & Neck Back 1.0mm ≤ A ≤ 1.4mm 1.0mm ≤ C ≤ 1.4mm Back Cover & Bezel Alignment 0 mm ≤...

  • Page 44

    Back Cover & Tuner Door 0.8 mm ≤ E ≤ 1.2 mm LV171-E08 Back Cover & Key Plate 0.6 mm ≤ F ≤ 1.2 mm LV171-E09...

  • Page 45

    8.4.2 LCD Horizontally The angle between front bezel and LCD unit in bottom side should be not large than 1.0mm. LV171-E10 The distance G-H of the LCD display unit from left side to right should be not large than 4.0mm. LV171-E11 Tilt Base Rotation Tilt up 25 ±...

  • Page 46: Plastic Material

    8.5 PLASTIC MATERIAL Front Bezel ABS 94HB, 94V-0 Back Cover ABS 94HB, 94V-0 The Others ABS 94HB 8.6 GAP SPEC. Gap between panel with bezel is 0.2 mm < gap < 1.5 mm...

  • Page 47: Block

    9 Block 9.1 MAIN BOARD BLOCK DIAGRAM...

  • Page 48: Tuner Board Block Diagram

    9.2 TUNER BOARD BLOCK DIAGRAM...

  • Page 49: Connect

    10 Connect 10.1 PCBA CONNECTOR LOCATION 10.1.1 K701-DM 10.1.2 R701-DM 10.1.3 VTV-N7910...

  • Page 51: Connector P/n Assignment

    10.2 CONNECTOR P/N ASSIGNMENT 10.2.1 CONNECTOR Function Location Function Type CN101 VGA I/P D-sub 15P Female -A CN201/CN552 Remote control 5P Housing CN202/CN550 KEY pad control 8P Housing CN1/CN654 Inverter PW I/P 13P Housing CN653/CN801 Tuner IN connector D-sub 15P M/Female -R CN301/CN652 Tuner I/P 6P wire...

  • Page 52

    10.2.2 CONNECTOR PIN ASSIGNMENT Location\ ISP- ISP- DDC- DDC- CN101 R-IN G-IN B-IN DET. Hsync Vsync CN201/ PWR- PWR- CN552 CN202/ OSD- OSD- OSD- OSD- OSD- OSD- OSD- CN550 CN1/ PAN- PAN- CN654 CN653/ MTS- VHS- MTS- MTS- MSDA MODE MSCL CN801 AVOUT LOUT...

  • Page 53: Appendix A: Pcba Assembly

    Appendix A: PCBA Assembly...

  • Page 54

    Chip Interfac L501 U502 L502 HI0805N310 LT1117-2.5 V +2.5V_VP +2.5V_VP HI0805N310 L505 +3.3V CVDD DVDD HI0805N310 C504 C505 C506 C507 C508 C509 C501 C502 R501 C503 C510 C511 47U/16V 0.1U 100U/16V 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 47U/16V +3.3V L506 MVDD A1BLU0...

  • Page 55

    L301 +3.3V_SAA L302 3V3B1 HI0805N310 HI0805N310 U301 CN301 R301 C305 C306 C307 C308 C309 C310 C311 C312 VIDEO-11P C304 Cr_IN C301 100U/16V 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U 0.1U AOUT AOUT P9 Y_IN 47U/16V C302 C303 Cb_IN 0.1U 100U/16V 3V3A1 AV1_RCA_COM L303...

  • Page 56

    LP601 LP603 LP605 LP607 33 *4 33 *4 33 *4 33 *4 B1BLU[0..7] A1BLU[0..7] B1RED[0..7] A1RED[0..7] B1BLU7 B2BLU7 A1BLU7 A2BLU7 B1RED7 B2RED7 A1RED7 A2RED7 B1BLU6 B2BLU6 A1BLU6 A2BLU6 B1RED6 B2RED6 A1RED6 A2RED6 B1RED5 B1BLU5 B2BLU5 A1BLU5 A2BLU5 B2RED5 A1RED5 A2RED5 B1RED4 B1BLU4 B2BLU4...

  • Page 57

    C551 27p-NC UCLK C550 0.1U U550 R550 X550 SM59264 1M-NC 14.318MHz-NC EA/VP EA/VP P0.0 UCLK2 P0.1 C552 UCLK P0.2 27p-NC P0.3 P0.4 UCLK2 R561 R560 P0.5 P0.6 P0.7 AD[0..7] P2 RESET MPU_Y P2.0 MPU_G R553 P2.1 C553 R552 /INT0 DSUB_DET D_DET MUTE_S MUTE_S P7...

  • Page 58

    TUNER OUT Connector P2,3 CN655 CONN DSUB 25-R +9V_ADO +9V_ADO P7 MSDA MSCL AU1_L GND_AI AU1_R GNDV AV-CVBS1 AU2_L AU1_L AU1_L +5V +12V1 AV_CHR AU2_R AV_LUM AU1_R AU1_R P7 TV_LOUT R657 TV_ROUT AU2_L AU2_L GNDV +12VT +12V L654 L655 +9V_ADO R655 39 / 2W-NC POWER SAVE CONTROL +12V...

  • Page 59

    C429 R413 C430 100U/16V 0.15U PGND LFOUT1 C438 4.7U/50V LFOUT GND1 GND_AO GND2 GND_AI R425 33K 1% R427 1.69k 1%.1.87k 1% for Hitachi GND_AO R429 R430 2.2K 2.2K CN401 GND_AI LFSPEAK RFOUT1 C439 4.7U/50V RFOUT TV_ROUT TV_ROUT C403 2.2U R405 2.4K...

  • Page 60

    +3.3V_AP L101 U101 L102 AR[0..7] P2 HI0805N310 LT1117-3 .3V HI0805N310 RP101 +3.3V L105 +3.3V_VD R124 VS_VGA 100 *4 HI0805N310 +3.3V_AP R101 R125 HS_VGA C101 47U/16V C103 C126 47U/16V C102 C152 C125 8200p 0.1U 0.1U 0.082U R123 2.2K R126 CLAMP_VGA R102 RP102 100 *4 G84D...

  • Page 61

    +3.3V_VDA L450 L451 AOUT AOUT HI0805N310 HI0805N310 +3.3V_VDC R450 L452 HI0805N310 C453 C450 C451 47U/16V C454 47U/16V 0.1U C455 0.1U 47U/16V C456 U450 R451 0.1U LT1117-3.3V +3.3V_VDA FBLK FBLK C452 47U/16V B-TEXT B-TEXT C464 G-TEXT G-TEXT 10U/16V P2.0/PWM P1.5 RES. R-TEXT R-TEXT P2.0/PWM0...

  • Page 62

    OSD_S0 OSD_S2 OSD_S3 OSD_S4 OSD_S5 OSD_S6 OSD_S7 S201 S202 S203 S204 S205 S206 S207 KSM0632B KSM0632B KSM0632B KSM0632B KSM0632B KSM0632B KSM0632B Source Min us Plu s Chann el Function Power CN202 VT4501-08 OSD_S7 OSD_S6 OSD_S5 OSD_S4 OSD_S3 OSD_S2 OSD_S0 Title SCHEMATIC, KEY/B VTV-K701,SLV87E Size Document Number...

  • Page 63: Appendix B: Display Unit Assembly

    R202 PWR_Y PWR_G R201 D201 LYG2093 YEL/GRN IR_DAT C202 U201 C201 2.2U/16V RIM-B38 1000P IR Receiver CN201 VA4301-05 PWR_G PWR_Y IR_DAT Title SCHEMATIC, IRKEY/B VTV-R701,SLV87E Size Document Number 404AB1 Date: Tuesday, June 17, 2003 Sheet...

  • Page 64

    T801 C821 L801 C817 0.1U C822 BLM21P300S C823 47U/16V +5V_VS 47U/16V MSCL MSDA C802 C801 0.1U 47U/16V L822 BLM21P300S R847 for hitachi R824 GNDTi GNDTi R802 GNDTi MTS_L L802 R825 CVBS TV_AVOUT BLM21P300S C825 CVBS C826 +5V_VIF 47U/16V R846 0.01U...

  • Page 65

    VTV-L701 4pcs 2pcs 2pcs 6pcs VTV-R701 4pcs 2pcs 4pcs...

  • Page 66

    THE UPDATED PARTS LIST FOR THIS MODEL IS AVAILABLE ON ESTA...

  • Page 67

    Fax: +46 (0) 8 562 711 13 Tel: +39 02 38073415 Servizio Clienti Email: csgswe@hitachi-eu.com Fax: +39 02 48786381/2 Email: customerservice.italy@hitachi-eu.com HITACHI EUROPE S.A.S HITACHI EUROPE LTD (Norway) AB Lyon Office STRANDVEIEN 18 B.P. 45, 69671 BRON CEDEX 1366 Lysaker FRANCE...

Comments to this Manuals

Symbols: 0
Latest comments: