LGB 21811 Instruction Manual page 10

INSTRUCTIONS FOR ADVANCED
USERS
MTS Onboard Decoder
Programming functions
You can program numerous func-
tions of the onboard decoder to suit
your requirements. If you want to do
this, program the "function values"
in "registers" (CVs) using a PC and
the 55045 MTS PC Decoder
Programming Module. You can also
program the function values using a
55015 Universal Remote.
Hints:
- For normal operation, it is not nec-
essary to change the function val-
ues.
- If programming results in unsatis-
factory operation, you can repro-
gram the factory pre-set values of
most important CVs: Program reg-
ister CV55 to function value 55.
This also reprograms the loco
address to the factory pre-set
value.
To reprogram the factory pre-set
function values with the 55015,
select programming mode "P" (dis-
plays shows "P --"). Then input 6, 5,
and 5 and press the right arrow but-
ton. The display shows "P --" again:
Input 5, 5, and 5 and press the right
arrow button again.
20
You can program the following registers:
Register Function
CV1 Loco address
CV2 Starting voltage
voltage for speed setting 1 - if loco starts only at a higher
speed setting, increase value.
CV3 Acceleration (1 = fast, 255 = slow)
CV4 Braking (1 = fast, 255 = slow)
CV5 Max. voltage
Voltage for highest speed step - if a lower top speed is
desired, decrease value.
CV5 after input of CV6 (when programming with older 55015)
function value for CV to be programmed
CV6 CV to be programmed (when programming with older 55015)
CV29 NMRA configuration
Bit programming
Bit 1: direction, 0 = normal, 1 = reversed [0]
Bit 2: speed steps, 0 = 14 (LGB), 2 = 28 [0]
Bit 3: analog operation, 0 = not possible, 4 = possible [4]
Bit 4: not used [0]
Bit 5: speed steps, 0 = factory-programmed,
16 = user-programmed [0]
Bit 6: address area, 0 = 0-127 (LGB), 32 = 128-10039 [0]
To program, add the values for the individual Bits and
program the resulting function value.
Hint: To program a loco to reversed direction of travel (for
example, F7 A-B-A combination), program function value 5.
Attention! Loco addresses 128-10039 and 28 speed steps
cannot be used with LGB MTS).
CV49 Voltage for function terminal F1
(depends on loco model, do not change, as functions
can be affected or destroyed)
CV50 Voltage for lighting terminals (see CV49)
CV51 Command for function terminal F1
0 = lighting button 9
1 = button 1 (buttons 2-8 not used)
9 = button 1 (buttons 2-8 used as well)
10 = button 2
11 = button 3
12 = button 4
13 = button 5
14 = button 6
15 = button 7
16 = button 8
64 = lighting button 9 (on only when loco is reversing)
65 = button 1 (on only when loco is reversing)
128 = lighting button 9 (on only when loco is moving forward)
129 = button 1 (on only when loco is moving forward)
Available Factory
values pre-set
(00-22) [3]
(0-255) [5]
(1-255) [3]
(1-255) [3]
(1-255) [255]
[4]
(1-32) [32]
(1-32) [5]
[13]
21