Subscribe to Our Youtube Channel
Related Manuals for AVLink PS-301
Summary of Contents for AVLink PS-301
-
Page 1: User Manual
User Manual Presentation Switcher with HDMI solutions PS-301/301M V.2016PS-301Series.00... -
Page 2: Copyright And Trademarks
COPYRIGHT AND TRADEMARKS All rights reserved by C&C TECHNIC TAIWAN CO., LTD. No part of this document may be reproduced in any form or by any means without written permission from the product manufacturer. Changes are periodically made to the information in this document. They will be incorporated in subsequent editions. -
Page 3: Before You Begin
BEFORE YOU BEGIN Follow all instructions marked on the device during using. Provide proper ventilation and air circulation and do not use near water. It is better to keep it in a dry environment. Place the device on a stable surface (example cart, stand, table, etc.). The system should be installed indoor only. -
Page 4: Table Of Contents
TABLE OF CONTENTS Copyright and Trademarks ......................1 Before You Begin .......................... 2 Table of Contents .......................... 3 Table of Figures ..........................4 Chapter 1 Switcher System Overview ..................5 1.1 Introduction ........................5 1.2 Packing ..........................6 Chapter 2 Features ........................7 Chapter 3 Specifications ...................... -
Page 5: Table Of Figures
TABLE OF FIGURES Figure 1-1 PS-301/PS-301M Switcher ................5 Figure 4-1 PS-301/PS-301M Switcher Front Panel ............9 Figure 4-2 PS-301 Switcher Rear Panel ................. 11 Figure 4-3 PS-301M Switcher Rear Panel ..............11 Figure 4-4 RS232 Pin Definitions ..................11 Figure 4-5 IR Blaster/Receiver Pin Definitions .............. -
Page 6: Chapter 1 Switcher System Overview
3x1 transmission interfaces. It is a switcher and also a converter means that it can handle virtually video/audio signals on its 3 HDMI inputs (PS-301) or 1 HDMI/1 VGA inputs (PS-301M). Split the HDMI signal and mix with the audio signal comes from the MIC input interface integrated the optical SPDIF or R/L stereo audio output signal. -
Page 7: Packing
1.2 Packing PS-301/PS-301M Switcher *1 Power Cord *1 DB9-F to 3.5mm Serial Cable *1 User Manual x 1... -
Page 8: Chapter 2 Features
CHAPTER 2 FEATURES 3 x HDMI In Up to 4K x 2K@30fps for PS-301, or 1 x HDMI In for PS-301M 1 x VGA In + 1 x 3.5Ø Stereo Audio Inputs Associated with Each VGA Connection (Only for PS-301M) -
Page 9: Chapter 3 Specifications
CHAPTER 3 SPECIFICATIONS Hardware LCD Module Pushbuttons Knob PS-301: HDMI Type A x 3 Input Connector PS-301M: HDMI Type A x 1/YPbPr x 1/VGA x 1 Output Connector HDMI Type A x 1/RJ-45 x 1 IR IN 3.5∅ Phone Jack x 1 IR OUT 3.5∅... -
Page 10: Chapter 4 Front/Rear Panels
CHAPTER 4 FRONT/REAR PANELS 4.1 Front Panel Figure 4-1 PS-301/PS-301M Switcher Front Panel The Switcher supports 2 switching keys (Input*1/Menu*1) on the Front Panel. The keys allow you to configure the connected signal quickly and indicate the connection status clearly showing on the LCD display. - Page 11 LCD: LCD display shows current switcher status and operation status. Press Menu key to switch the LCD display screen. LCD Display Description * IN: Show you currently AUD OUT configuration is IN1~IN3. PS-301: IN1 → HDMI IN1 IN2 → HDMI IN2 IN3 → HDMI IN2 PS-301M: IN1 →...
-
Page 12: Rear Panel
Figure 4-2 PS-301 Switcher Rear Panel Figure 4-3 PS-301M Switcher Rear Panel The Switcher supports input jacks (HDMI x 3 for PS-301 and HDMI*1/VGA+Audio sets for PS-301M), MIC input port x1 and multiple output interfaces on the rear panel. The input interfaces allowing you to connect to different equipments including CD/DVD players, Blue Ray player, PS3, Video Camera, STB and so on. -
Page 13: Figure 4-5 Ir Blaster/Receiver Pin Definitions
IR (RX/TX): Through a IR Blaster/Receiver cable connection, you can extend the IR signals transmission between Switcher and Remote devices. IR Blaster IR Receiver Figure 4-5 IR Blaster/Receiver Pin Definitions HDMI OUT: The Switcher Output connector is connected to the A/V, HDTVs or other output devices directly. - Page 14 Audio R/L: The Switcher supports the stereo R/L audio input interface. (Only for PS-301M.). L+L- GND R+R-: The connector is used to connect the extender with audio amplifier. VGA IN +Audio IN: These ports receive the VGA and Audio signals through VGA and Audio cables come from the input sources.
-
Page 15: Chapter 5 Connections
CHAPTER 5 CONNECTIONS Figure 5-1 PS-301 Connections... -
Page 16: Figure 5-2 Ps-301M Connections
Figure 5-2 PS-301M Connections... -
Page 17: Input Connections
5.1 Input Connections Use the HDMI/VGA+Audio connecting cable to connect the Input serial jack (HDMI IN/ VGA IN/Audio IN) to the output source jack of the Blu-ray/DVD player displays/graphics workstations/PC. Figure 5-3 Input Connections 5.2 Output Connections Use the HDMI cable to connect the output jack (OUT1 ~ OUT2 with HDMI interface) on the rear panel to the input jack of the projector, video recorder, display, HD TV or multiplexer directly. -
Page 18: Multiple Connections
5.3 Multiple Connections MIC: Connected to the microphone. SPDIF: Uses the SPDIF cable with RCA or Toslink connector to connect the SPDIF port on the rear panel to the AVR device. Then, transmit signals through coaxial or fibre optic of SPDIF cable. Audio R/L: Uses the Audio R/L cable to connect the R/L port to DVD Player for audio connection. -
Page 19: Ir Pass-Through Connection
5.5 IR Pass-Through Connection The Switcher provides an IR Receiver cable and IR Blaster cable accessories for IR pass-through; on the other hand, it also provides you an extended IR pass-through transmission through Extender. Supports you an IR channel to control the TV-end of your Switcher and Remote. Supports all kinds of IR frequency band You can extend the signal connection through the Extender described as below. -
Page 20: I/O Ports
5.7 I/O Ports 5.7.1 RS232 The RS232 Pin functions are described as below: Pin No. Abbreviation Description Null Send Receive Null Ground Null Null Null Null Figure 5-8a RS232 Pin Function Figure 5-8b RS232 Pin Function... -
Page 21: Hdbt
Figure 5-8c RS232 Pin Function The Switcher RS232 port is defined by DCE. 5.7.2 HDBT The Switcher supports HDBaseT output for a long distance signal transmission. Output connector is RJ-45 jack with two LED indicators using the 8P8C modular connector, which specifies the physical male and female connectors as well as the pin assignments of the wires in a LAN cable. -
Page 22: Output Cable
* The left of RJ-45 output jack is specified for HDCP LED (Yellow). * The right of RJ-45 output jack is specified for LINK LED (Green). The LED indicators are only designed for the Output – RJ-45 jack of the Switcher. LED Indicators: Blink LINK... - Page 23 The VS010 family features the following: When the VS010 is in low power mode (LPPF1/2), the sample rate of the PDIF channel is reduced to 100 KHz. This implies that high data rates may not be used when the VS010 is in LPPF. Enables 10.2 Gbps of HDMI 1.4 traffic (including HDCP) over a single LAN cable according to the following specifications: Cable Type...
-
Page 24: Chapter 6 Troubleshooting
CHAPTER 6 TROUBLESHOOTING 1. What to do if LCD is fail in display? Answer: Check the connection of power cord is not loosening and the power cord is in a good status having no any damage. Check the power source is normally. 2. - Page 25 5. What to do if you sense the power leakage during plugging or unplugging of the input/output ports? Answer: It could be that the equipment power is not properly grounded. You must properly ground your equipment; otherwise product life can easily be shortened. 6.
-
Page 26: Appendix A Hdbaset Firmware Upgrade
APPENDIX A HDBASET FIRMWARE UPGRADE Process the Update TX_xxx.bat or UpdateRX_xxx.bat file to upgrade firmware. (xxx is specified for firmware version) These files are used for upgrading the VS010TX/VS010RX IC in your devices. The UpdateTX_xxx.bat file is used to upgrade the Switcher or D.A system (the VS010TX IC in your Switcher) firmware. -
Page 27: Figure A-2 Hx-Sruw F/W Upgrade 2
Figure A-2 HX-SRUW F/W Upgrade 2 4. On the control PC, process the UpdateRX_23090-C.bat file to upgrade firmware. (The update file name is only for reference, it will be different based on version.) Figure A-3 HX-SRUW F/W Upgrade 3... -
Page 28: Switcher Hdbaset F/W Upgrade
5. Final, the update is finished as below. Figure A-4 HX-SRUW F/W Upgrade 4 A-2 Switcher HDBaseT F/W Upgrade Follow the steps as below to upgrade the Switcher firmware: 1. Connect the control PC and HX-SRUW with a RS232 cable. Figure A-5 Switcher HDBase T F/W Upgrade 1... -
Page 29: Figure A-6 Switcher Hdbase T F/W Upgrade 2
2. Connect the TV and HX-SRUW with a HDMI cable. Figure A-6 Switcher HDBase T F/W Upgrade 2 3. Connect the DVD Player and Switcher with a HDMI cable. Figure A-7 Switcher HDBase T F/W Upgrade 3 4. Connect the LAN cable to the LINK IN port on the side panel of Extender. The other end of the LAN cable connected to the HDBT port of Switcher. -
Page 30: Figure A-8 Switcher Hdbase T F/W Upgrade 4
Figure A-8 Switcher HDBase T F/W Upgrade 4 5. Connect the DC 12V adapter. 6. Enable the Switcher, TV and DVD player power, and play the video comes from the DVD Player. 7. Adjust the HX-SRUW F/W Upgrade switcher to LOCAL mode. Local (Switcher) Firmware Upgrade Pin 1 Pin 2... -
Page 31: Figure A-10 Switcher Hdbase T F/W Upgrade 6
8. On the control PC, process the UpdateTX_23090-C.bat file to upgrade firmware. (The update file name is only for reference, it will be different based on version.) Figure A-10 Switcher HDBase T F/W Upgrade 6 9. Final, the update is finish as below. Figure A-11 Switcher HDBase T F/W Upgrade 7 10. -
Page 32: Appendix B Extender
APPENDIX B EXTENDER The extension of HDMI video signal device supports up to 70 meters away by using an Extender and Cat.5e cable. HDMI Extender is ideal for: Test bench facilities Data Center Help desks HX-SRUW Extender Front Panel View Rear Panel View Figure B-1 HX-SRUW Extender... -
Page 33: Features
Through the RS232 connection to upgrade REMOTE Receiver unit. Through the LAN Connection to upgrade LOCAL Transmitter (PS-301/PS-301M). Extend the RS232 Signal Transmission NORMAL B-1 Features Through the Extender, you can use the output of the Switcher to display identical... -
Page 34: Specifications
B-2 Specifications Hardware HDMI OUT HDMI A-Type Female x 1 LINK RJ-45 Connector x 1 IR OUT 3.5ψ Stereo Jack x 1 IR IN 3.5ψ Stereo Jack x 1 2 Pins Dip Switch F/W Upgrade Setting RS232 Connector DB9 Female x 1 (For F/W Upgrade) LED indicators MODE/LINK/HDCP/POWER Power Supply... -
Page 35: Ir Receiver Cable Directions
B-3 IR Receiver Cable Directions Put IR Receiver cable into the Receiver “IR IN” port and place the IR Receiver Cable, so that you can aim at it easily with your IR remote controller. IR Receiver Cable: Figure B-2 IR Receiver Cable B-4 IR Blaster Cable Directions Plug IR Blaster cable into Receiver “IR OUT”... -
Page 36: Wiring Information For Link Connector
B-6 Wiring Information for Link Connector Figure B-5 RJ-45 Pin Assignment RJ-45 Pin Assignment: Conductor RJ-45 Pin Color Code for Identification Assignment Conductor White-Blue Pair 1 Blue White-Orange Pair 2 Orange White-Green Pair 3 Green White-Brown Pair 4 Brown... -
Page 37: Appendix C Extend Audio Amplifier
APPENDIX C EXTEND AUDIO AMPLIFIER The Switcher allows you to connect an audio amplifier for the extended speaker. Electrical power transferred from an audio amplifier to a loudspeaker, the speaker power handling is reached to 25W. Extend Audio Amplifier Front Panel View Rear Panel View Figure C-1 Extend Audio Amplifier LED Indicators (Green):... -
Page 38: Audio Amplifier Connection
C-2 Audio Amplifier Connection Figure C-2 Audio Amplifier Connection...
Need help?
Do you have a question about the PS-301 and is the answer not in the manual?
Questions and answers