Advertisement
gases from a lead acid battery, and DO NOT cover or obstruct the unit's ventilation louvres.
If battery has caps to access the battery fluid, remove the caps and check the fluid level before connecting the power clamps. If
9
necessary top-up the battery with distilled water by referring to the battery manufacturer's instructions (Apply the personal
safety precautions described in part 1.2).
If the unit receives a sharp knock or blow the unit must be checked by a qualified service agent before using.
9
If the battery terminals are corroded or dirty clean them before attaching the power clamps.
Keep children and unauthorised persons away from the working area.
9
8 8 DO NOT disassemble the unit for any reason. The unit must only be checked by qualified service personnel.
8 8
8 8 DO NOT try to charge a non-rechargeable battery.
8 8
8 8 DO NOT try to start engine when charger is connected to battery.
8 8
8 8 DO NOT try to charge battery if battery fluid is frozen.
8 8
WARNING! To prevent the risk of sparking, short circuit and possible explosion DO NOT drop metal tools in the battery area, or allow
‰
them to touch the battery terminals.
8 8 DO NOT allow power clamps to touch each other or to make contact with any metallic part of the vehicle.
8 8
DO NOT cross connect power leads from charger to battery. Ensure positive (+/RED) is to positive and negative (-/BLACK) is to negative.
8
DO NOT pull the cables or clamps from the battery terminals.
8
DO NOT use the unit outdoors, or in damp, or wet locations and DO NOT operate within the vicinity of flammable liquids or gases.
8
8 8 DO NOT use unit inside vehicle or inside engine compartment.
8 8
8 8 Ensure there is effective ventilation to prevent a build-up of explosive gases, and do not cover or obstruct charger ventilation louvres.
9
8
DO NOT use the unit for a task for which it is not designed.
8
WARNING! DO NOT simultaneously charge batteries of different capacities or discharge levels.
‰
WARNING! If a fuse blows, ensure it is replaced with an identical fuse type and rating. Use only Sealey genuine parts.
‰
8 8 When not in use, store the unit carefully in a safe, dry, childproof location.
9
8
NOTE: This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory
or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the
appliance. Cleaning and user maintenance shall not be made by children without supervision.
i
2.
INTRODUCTION
High frequency power supply utilises a microprocessing CPU controller when charging a battery and providing support during prolonged
electronic diagnostic checks. Designed for use with lead-acid batteries including WET, GEL and AGM types on 12V systems. Includes a function
to recharge a deeply discharged battery. Safety circuitry which includes reverse polarity protection, short circuit protection, overload protection
and the detection of voltage errors. Once fully charged, the battery may be left connected to be automatically conditioned and maintained.
3. SPECIFICATION
Model no: .............................................................. BSCU100
Type: ............................................. Microprocessor controlled
Supply: ...........................................................................230V
Output: .............................................................................12V
Output charge: ............................................................1-100A
Battery range: .........................................................5-1000Ah
BSU supply: .................................. 100A - 13.8V/14.5V/14.8V
4. ASSEMBLY
4.1.
Fit cable holders Refer to fig.1
4.1.1.
Screw cable holders to each side as shown in fig.1.
4.2.
Fit cable clamps Refer to fig.2
4.2.1.
Push cable through insulating handles.
4.2.2.
Locate cable using cable screw washer and nut, note which way up
cable needs to be. Screw on cable clamp tightly.
4.2.3.
Screw up cable screw tightly.
4.2.4.
Push outer protection pieces onto the ends of the clamp.
4.2.5.
Slide insulating handles up to meet the outer protection pieces.
4.2.6.
Repeat for other clamp.
© Jack Sealey Limited
Original Language Version
Fig.1
Fig.2
BSCU100 | Issue:1 09/11/15
Advertisement
