Unpacking And Mounting; Preparing Electrodes - DGP -PG3-V2 Operation Manual

5. UNPACKING & MOUNTING
t
5 . UNPACKING & MOUNTING
5. UNPACKING & MOUNTING
The first thing you should do is check for shipping damage. Diamond Ground Products, Inc. takes great pride
The first thing you should do is check for shipping damage. Diamond Ground Products, Inc. takes great pride
in producing quality products. If for some reason you find anything to be defective, please contact the Service
in producing quality products. If for some reason you find anything to be defective, please contact the Service
Department at (805) 498-3837 and we will work with you to rectify the problem to your satisfaction.
Department at (805) 498-3837 and we will work with you to rectify the problem to your satisfaction.
After unpacking the box you should have these items:
After unpacking the box you should have these items:
• The Piranha III Tungsten Grinder.
• The Piranha III Tungsten Grinder.
• Three Allen wrenches, sizes 3/32", 7/64" & 1/8" for replacing wheels.
• Three Allen wrenches, sizes 3/32", 7/64" & 1/8" for replacing wheels.
• PIII Manual
• PIII Manual
• Pin Vise
• Pin Vise
Mounting of the grinder is as follows. Place the unit on a flat surface allowing enough space for the operator to
Mounting of the grinder is as follows. Place the unit on a flat surface allowing enough space for the operator to
work in. This also provides proper ventilation. Make sure the power switch is in the off position and plug it into
work in. This also provides proper ventilation. Make sure the power switch is in the off position and plug it into
the electrical outlet. Switch the power on and the unit is ready to operate.
the electrical outlet. Switch the power on and the unit is ready to operate.
t

6 . PREPARING ELECTRODES

6. PREPARING ELECTRODES
6. PREPARING ELECTRODES
ADJUSTING HANDLES
ADJUSTING HANDLES
The set up procedure for the included angle may require
The set up procedure for the included angle may require
the use of both adjustment Handles, which are listed
the use of both adjustment Handles, which are listed
above as A and B. When Handle A is loosened, it allows
above as A and B. When Handle A is loosened, it allows
you to rotate the Universal Collet Arm to choose the
you to rotate the Universal Collet Arm to choose the
included angle that you would like to grind your tungsten.
included angle that you would like to grind your tungsten.
Handle B allows you to adjust the location at which the
Handle B allows you to adjust the location at which the
tungsten will touch the wheel.
tungsten will touch the wheel.
The Body Stop Gauge depth is set with Knob C and
The Body Stop Gauge depth is set with Knob C and
locked in place with Nut D.
locked in place with Nut D.
THE SET UP PROCEDURE
THE SET UP PROCEDURE
With the power turned off, select the included angle you would like to grind by:
With the power turned off, select the included angle you would like to grind by:
1) Loosening Handle A
1) Loosening Handle A 2) Turning the Collet Arm on its axis until the Pointer is directed at the angle on the scale you desire.
2) Turning the Collet Arm on its axis until the Pointer is directed at the angle on the scale you desire. 3) Re-tightening Handle A.
3) Re-tightening Handle A.
Next, put the tungsten at the diameter you plan to use through the proper sized collet hole on the universal collet
and observe the height at which the tungsten will hit the wheel. For setting up your first tungsten on a wheel,
Next, put the tungsten at the diameter you plan to use through the proper sized collet hole on the universal collet
and observe the height at which the tungsten will hit the wheel. For setting up your first tungsten on a wheel, make the height as close to the top of the wheel as possible by:
1) Loosening Handle B.
make the height as close to the top of the wheel as possible by:
2) Slide Collet Arm up to desired position.
1) Loosening Handle B.
3) Re-tightening Handle B.
2) Slide Collet Arm up to desired position.
3) Re-tightening Handle B.
The setup in now complete. After grinding numerous tungstens, you will wear a groove on the wheel. At this
point, adjust Handle B again and move the contact point down a very small amount to a fresh spot on the wheel.
The setup in now complete. After grinding numerous tungstens, you will wear a groove on the wheel. At this
point, adjust Handle B again and move the contact point down a very small amount to a fresh spot on the wheel.
DGP-PG3-A Product User Manual | Released: 11/16 Rev. H | ©2017 Diamond Ground Products
Copyright©2017, Arc-Zone.com®, Inc. All Rights Reserved
DGP-PG3-A Product User Manual | Released: 11/16 Rev. H | ©2017 Diamond Ground Products
2091 Las Palmas Drive, Ste. F
Page 5
Carlsbad, CA 92011 - Tel. 1.760.931.1500
Email: info@arc-zone.com
Page 5
A
A
Arc-Zone.com, Inc.
C
C
D
D
B
B
5 / 13