Philips Norelco D-Finer D350 Manual

4203.000.5253.2.qxd 5/2/03 4:44 PM Page 1
FEATURES
ENGLISH
IMPORTANT SAFETY
INSTRUCTIONS
When using an electrical appliance, basic safety
precautions should always be followed, including
the following:
Read all instructions before using this
appliance.
DANGER
To reduce the risk of electric shock:
1. Do not reach for a Shaper that has fallen
into water. Unplug immediately.
2. Do not use while bathing or in a shower.
I
3. Do not place or store Shaper where it can
fall or be pulled into a tub or sink. Do not
place in or drop into water or other liquid.
4. Always unplug this Shaper from the electrical
outlet immediately after using, except when
Shaper is (re)charging.
5. Unplug Shaper before cleaning.
6. When discarding Shaper, unplug Shaper and
A. Removable Shaving Head
remove rechargeable battery. See Battery
B. Shaving mini-foil
Removal instruction sheet.
C. Protective Cap
D. Specialty Hi-Definition Trimmer
WARNING
E. On/Off Switch
F. Charging Indicator Light
To reduce the risk of burns, fire, electric
shock or injury to persons: G. Power Cord Socket
1. Close supervision is necessary when
H. Power Cord
this appliance is used by, on, or near children
I. Adaptor
or invalids.
J. Cleaning Brush
2. Use this Shaper for its intended household
K. Full Two-Year Warranty
use as described in this manual. Do not use
L. 60-Day Money-Back Guarantee
attachments not recommended by Philips
Electronics North America Corporation.
To Charge/Recharge
3. Never operate this Shaper if it has a
◗ (Re)charging requires 10 full hours.
damaged cord or plug, if it is not working
properly, if it has been dropped, damaged, or ◗ Use only the cord provided.
dropped into water. Return the Shaper to an
◗ Battery performance is best if you recharge
Authorized Norelco Service Location for
only when the battery is (almost) completely
examination and repair.
empty.
4. Keep the Shaper and cord away from heated ◗ Charging or recharging at temperatures below
surfaces.
40˚F or higher than 95˚F adversely affects
lifetime of the battery.
5. Never drop or insert any object into any
◗ Continuously recharging Shaper will reduce
opening.
life of battery.
6. Do not operate, charge or plug in Shaper
1 Be certain Shaper is OFF.
outdoors or where aerosol (spray) products
are being used or where oxygen is being 2 Connect the power cord
administered.
plug to Shaper (Fig. 1).
7. Do not use this Shaper with a damaged or
broken specialty Hi-Definition Trimmer or
mini-foil, as facial injury may occur.
8. Always attach plug to Shaper first, then to
Do not charge Shaper for more than 24 hours.
outlet.To disconnect, turn on/off switch to
"OFF" position (switch is down), then
remove plug from outlet. 3 Plug adaptor into any 120V AC outlet.
Use only the cord provided.
9. To prevent possible damage to the cord, do
4 Green Charging Indicator
not wrap cord around the Shaper.
Light on the adaptor will
10.Never put Shaper in direct sunlight or store go on to indicate the
at a temperature above 140°F. Shaper is charging (Fig. 2).
A full charge takes
11.This Shaper is for use on human facial hair
approximately 10 hours
only. Do not use this Shaper for any other for up to 40 minutes of
purpose.
cordless operation.
12.Always store your Shaper and adaptor in a
5 Remove the adaptor from the electrical
moisture-free area. Make sure the cord is outlet and disconnect the power cord
disconnected from the Shaper. plug from the Shaper.
6 When the battery is empty, recharge the
SAVE THESE
appliance for 10 hours. The Shaper does
not operate directly from the electrical
INSTRUCTIONS
outlet. If you want to style your facial
hair when the battery is empty, charge
the appliance at least 90 minutes to
IMPORTANT: YOUR SHAPER
ensure enough power for the one styling
CONTAINS A NICKEL-CADMIUM
session.
RECHARGEABLE BATTERY. See Battery
Removal instruction sheet.
Optimize the working life of the battery
After the Shaper has been charged for the
first time, do not recharge it between styling
sessions. Continue using it until the battery is
almost completely empty.
◗ Discharge the battery completely twice a year
by letting the motor run until it stops. Then
recharge the battery for at least 10 hours.
◗ Do not charge the appliance for more than
24 hours.
◗ Do not keep cord permanently plugged into
the electrical outlet.
◗ If Shaper hasn't been used for a long period
of time, it must be recharged for a full 10
hours.
Gently press the shaving mini-foil to the skin.
D-Finer Precise Shaper with
Do not press too hard.
Dual Defining Technology
To maintain a shape, use the shaving mini-foil
Put it to the test. Like many new products, to shave along the edges to provide a smooth
your Norelco D-Finer Precise Shaper may take
and clean beard line.
a little getting used to. So take the time to get
2
acquainted with the two-step shaping and Switch the D-Finer Shaper OFF. Put on
finishing process. Use the narrow specialty Hi- the protective shaving head cap to
Definition Trimmer to shape your beard, even protect the specialty Hi-Definition
in the smallest areas. Then follow-up with the Trimmer and the shaving mini-foil.
narrow shaving mini-foil to shave along the
edges and eliminate any stubble to create a
smooth and clean contoured beard line.
CLEANING
Use the D-Finer Precise Shaper in addition to
your beard trimmer and razor to create and
◗ Always switch D-Finer Precise Shaper off
maintain the beard shape that defines your
before cleaning.
personal style.The unique ergonomic design
◗ Do not use abrasives, scourers or liquids such
makes it easy to see exactly what you're doing
so you get precisely the look you want. as alcohol, benzene, bleach or acetone to
clean the D-Finer Shaper.
◗ Never clean the specialty Hi-Definition
Before You Begin
Trimmer or shaving mini-foil with the motor
ON.
Preparing your beard for shaping
◗ Do not apply pressure to specialty Hi-
Follow these steps to prepare your beard.
Definition Trimmer or shaving mini-foil. Do
not touch specialty Hi-Definition Trimmer or
shaving mini-foil with hard objects as this may
1 Use a Norelco beard and
3
damage them.
moustache trimmer to
◗ Do not use while bathing, showering or
trim your beard (Fig.3).
immerse the D-Finer in water or other liquids
as damage to D-Finer Shaper may occur.
◗ Clean cut hairs from D-Finer Shaper as they
accumulate during use.
◗ Always clean D-Finer Shaper after each use
2 Use a Norelco razor to 4
shave larger areas of the
and before storing.
skin (Fig.4).
1 Make sure D-Finer Shaper is switched
OFF and disconnected from the electrical
outlet.
2
Shaping Make sure the specialty Hi-Definition
Trimmer is down in its original position.
Now you can shape and define your facial hair
style. 3 Remove the removable
shaving head by pulling it
Use the D-Finer Precise Shaper on a clean, dry off the D-Finer body
face. Do not use any type of lotion or cream (Fig. 8).
before using.
Use the Precise Shaper only for its intended
4 Shake or blow cut hairs from the shaving
household use as described in this manual.
head. Carefully clean the cutting unit and
1 Slide the specialty Hi- the shaving head and body of the D-Finer
5
Shaper with the brush supplied.
Definition Trimmer out
until you hear a "click"
Important: Do not clean the shaving mini-
and the Hi-Definition
foil with the brush. The brush may damage the
Trimmer snaps into
position.You will see the shaving mini-foil.
slide-out mark (Fig. 5).
5 Put on the protective
1
shaving head cap to
The slide-out mark is hidden underneath the
specialty Hi-Definition Trimmer and only protect the specialty Hi-
Definition Trimmer and the
becomes visible when the specialty Hi-
shaving mini-foil (Fig. 9).
Definition Trimmer has been slid out correctly
and "clicks" into position.
Replacing The Shaving Mini-foil
2 Switch the D-Finer Precise Shaper ON.
If the shaving mini-foil is worn or damaged, do
3 Shape the contours of your beard and
not continue using the appliance. Replace the
sideburns with the specialty Hi-Definition
shaving mini-foil immediately.
Trimmer.
4 To contour most
A worn or damaged shaving mini-foil should
2 6
effectively, place the flat
only be replaced with an original Philips
surface of the specialty Hi-
shaving mini-foil, which is available at an
Definition Trimmer in
authorized Norelco Service Location.
contact with the skin and
move it against the
1 Remove the detachable
direction of hair growth
shaving head by pulling it
(Fig. 6).
from the appliance (fig. 10).
5 Make well-controlled movements. Touch
the hair lightly with the specialty Hi-
Definition Trimmer.
2 Remove the shaving mini-
foil by pushing it out of the
NOTE: Since all hairs do not grow in the same
shaving head (fig. 11).
direction, you may want to try different
contouring positions (i.e., upwards,
downwards, or across). Practice is best for
optimum results.
For additional styles and defining tips, visit our
3 Place the new shaving mini-
website: www.norelco.com/d-finer.
foil carefully in the shaving
head (fig. 12).
When you have created your desired beard
contour, slide the specialty Hi-Definition
Trimmer back down to its original position.
4 When the shaving mini-foil
is properly positioned,
Finishing
push it into its end
position with your finger
1
Finally, use the narrow
7
(fig. 13).
shaving mini-foil to shave
along the contour edges to
remove any stubble while
creating a smooth clean
Replacing The Mini-foil Cutter
beard line (Fig. 7).
The mini-foil cutter is located under the
Before using mini-foil, always check mini-foil
detachable shaving head.
for wear or damage. If mini-foil shows signs of
wear or damage, do not use shaver as injury
Do not switch the appliance on when replacing the
may occur. Do not use until mini-foil has been
mini-foil cutter.
replaced.
If the mini-foil cutter is worn or damaged, do
not continue using the appliance. Replace the
mini-foil cutter and the shaving mini-foil
immediately.
60-DAY MONEY-
A worn or damaged mini-foil cutter should
BACK GUARANTEE
only be replaced with an original Philips cutter,
which is available at an authorized Norelco
Service Location. If you are not fully satisfied with your Norelco D-Finer
Precise Shaper, send the product back and we'll refund
14
you the full purchase price.
1 Remove the detachable
The D-Finer Precise Shaper must be shipped pre-
shaving head by pulling it
paid by insured mail, insurance prepaid, and have
from the Shaper (fig. 14)
the sales receipt, indicating purchase price and the
date of purchase, enclosed.The D-Finer Precise
Shaper must be postmarked no later than 60 days
after the date of purchase. Norelco reserves the
2 right to verify the purchase price of the D-Finer
Remove the old mini-foil
15
Precise Shaper and limit refunds not to exceed sug-
cutter by pulling it from the
gested retail price.
appliance (fig. 15).
Send dated sales receipt, your complete name and
address as indicated below, and the D-Finer Precise
Shaper, prepaid to:
Norelco Consumer Products Company
3
Make sure that the spring within the A Division of Philips Electronics
driving unit does not get lost. North America Corporation
450 North Medinah Road, Dock 16
Roselle, IL 60172-2329
16
Please allow 4-6 weeks for delivery of check.
Name
4
Insert the new mini-foil
cutter carefully into the Address
driving unit (fig. 16).
City
State Zip
Daytime Telephone No. ( )
17
5 AREA CODE
When the mini-foil cutter
Email Address:
is properly positioned,
REASON FOR RETURNING:
push it into its end
position with your finger
(fig. 17).
6
Replace the detachable shaving head on
the Shaper.
This shaper has no other user-serviceable parts. Any
8 other service should be performed by an Authorized
Norelco Service Location.
Assistance
For assistance or the Authorized Norelco
Service Location nearest you, call toll free:
1-800-243-3050
or for live help online visit our website:
www.norelco.com
Authorized Norelco Service Location
information is available 24 hours a day, 7 days a
week.
9
Battery Removal
◗ This Norelco D-Finer Shaper contains a
rechargeable Nickel-Cadmium battery, which
must be disposed of properly.
◗ Battery should only be removed when D-
Finer Shaper is to be discarded.
◗ Refer to Battery Removal instruction sheet for
directions on removing the rechargeable
battery.
10
11
12
13