Table of Contents
Advertisement
E9017FD_EN.qx3
03.8.6
VCR Manual Recording
Direct dubbing
Follow the steps below to copy a DVD or video disc to a
videotape.This will be possible only if the DVD is not copy
protected.
1 Put a videotape in the cassette compartment. Make sure the
tape's record tab is intact and the tape is long enough to
record the disc.
2 Press VCR.
3 Select the recording speed.
Details are at "Selecting the recording speed (SP or LP)".
4 Put the DVD you want to copy in the disc tray.
5 Press DVD.
6 Press PLAY B.While disc is playing, press PAUSE k at the
point you wish to start recording.
7 Press DIRECT DUBBING to record.
To pause the recording.
Press PAUSE k.
To resume recording.
Press PAUSE k again.
To stop the recording.
Press STOP C.
Recording(From DVD To VCR)
1 Insert a DVD without copyright protection in the tray.
2 Insert a video cassette tape with its erase prevention tab in
place.
3 Select the recording speed.
Details are at "Selecting the recording speed (SP or LP)".
4 Enter "004" with numerical key pads to appear "DISC" on the
TV screen.
5 Press REC I.
6 Change to DVD operation mode.
7 Press DVD, then PLAY B to begin the playback of a DVD.
8 Press VCR, then STOP C to stop recording.
10:13 AM
Page 13
Programming a Recording (TIMER)
General information
Use a TIMER programming to automatically start and stop a recording
at a later time or date.The System will switch to the right programme
number and begin recording at the correct time.With this System, you
can pre-programme up to eight recordings within a period of one
year.To make a programmed recording, your System needs to know:
* the date you want to make the recording
* the programme number of the TV channel
* the start and stop time of the recording
* VPS or PDC on or off
This information is saved in a TIMER block.
What is 'VPS/PDC'?
'VPS' (Video Programming System)/ 'PDC' (Programme Delivery
Control) are used to control the start and duration of TV channel
recordings. If a TV programme starts earlier or ends later than sched-
uled, the System will turn on and off at the correct time.
What do I need to know about 'VPS/PDC'?
Usually the VPS or PDC time is the same as the start time. But if
your TV guide shows a VPS or PDC time which is different from
the programme's scheduled start time, e.g. 20.10 (VPS/PDC
20.14), you must enter the VPS/PDC time exact to the minute. If
you want a start time different from the VPS/PDC time, you must
switch VPS/PDC off.
Programming a recording
(with the 'S
V
HOW
IEW
You no longer need to tediously enter the date, programme
number, start and end time. All the information needed for pro-
gramming is contained in the S
You can find this S
V
HOW
IEW
zines written next to the concerned programme.
1 Press SV/V+.
2 Enter the entire S
V
HOW
IEW
ber.This number is up to 9 digits
long and can be found next to the
start time of the TV programme in
your TV listing magazine. [e.g: 1-
234-5 or 1 234 5]
If you make a mistake, you can
clear your input with CLEAR.
3 Press SV/V+.
4 Select ONCE, DAILY or WEEKLY
recording with K/L.Then press B.
Selecting once/daily/weekly recordings
Using K/L, select from the following options:
'ONCE':
Recording once
'DAILY':
Repeated daily recordings (Monday to Friday)
'WEEKLY': Repeated weekly recordings (every week on the same
day)
'- -' appears at PROG. .
* The programme number of the TV channel has not yet been
assigned to the S
V
number. Using the numerical key
HOW
IEW
pads, select the corresponding programme number (name) of
the TV channel.
The following message appears on the screen:'ERROR'
* The entered S
V
number is incorrect. Correct your input
HOW
IEW
or end with DISPLAY/STATUS/EXIT.
* Check the time/date (see chapter 'Installing your video', section
'Setting the time and date').
* A daily recording was entered for the wrong day. Daily pro-
gramming can only be used for recordings to be made from
Monday to Friday.
The following message appears on the screen:'TIMER
NOT COMPLETED'
* The channel is wrong.
® system')
R
V
-programming number.
HOW
IEW
number in most TV listing maga-
ShowView system
num-
ShowView No.
12345 – – – –
SET=SV/V+
CORRECT=CLEAR
END=EXIT
ShowView system
ONCE
DAILY
WEEKLY
SELECT K L CHOOSE B
END=EXIT
13
Advertisement
Table of Contents
