Caliber RDD 802BT Manual
  1. Manuals
  2. Brands
  3. Caliber Manuals
  4. Car Video System
  5. RDD 802BT
  6. Manual

Caliber RDD 802BT Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Advertisement

Table of Contents
loading

Related Manuals for Caliber RDD 802BT

Summary of Contents for Caliber RDD 802BT

  • Page 2: Tools For Installation

    INSTALLATION Tools for Installation Use the 2 removal wrenches of the old unit to take out the old unit and place with this brand new car radio. The following tools and sup- plies may also be needed for the installation: Tools for Installation: Philips Screw-drivers /Machine Screws /Wire Stripper /Wire Cutter /Hammer /Pencil /Electrical Tape /Electric Drill Supplies for Installation: Machine Screws /Crimp Connectors /14 Gauge Wire for Power Connections /14-16 Gauge Speaker Wires The above are not supplied.
  • Page 3 INSTALLATION WARNING: Disconnect negative battery terminal from battery before starting installation. Consult the vehicle’s owner’s manual for proper instructions. NOTE: Mark the polarity of the existing speaker wires before disconnecting battery. NOTE: Remove the two transport screws from the top of the unit before installing. NOTE: Make sure there is enough space for the installation of this double-din unit.

  • Page 4: Wiring Diagram

    WIRING DIAGRAM Amplifier CAMERA BACK power (+12V output - blue/white) External Microphone (black - 3,5mm Jack) Radio Antenna (steering wheel control - 3.5mm jack) Reverse(purple-white) Parking (green) SUB 1 OUT (white) Connector A Connector B SUB 2 OUT (red) 1. Rear right speaker(+)/Purple 1.
  • Page 5 WIRING DIAGRAM General Wiring Notes: Make sure You have a good chassis ground. Good ground connection will eliminate most electrical noise problems. A good chassis ground requires a tight connection to the .vehicle’s metal chassis. The area around the ground connection should be clean, bare metal without rust, paint, plastic, dust, or dirt for a good ground connection.

  • Page 6: Specifications

    Specifications GENERAL Operating Power............................12 Volts DC, Negative Ground Output Wiring..........................Designed for using four speakers only RCA line out..............................low-level outputs - 1000MV Output Impedance..........................Compatible 4 to 8 Ohm Speakers Fuses.........................................10 amp Dimensions............................128mm(W) x 125mm(D) x 100mm (H) Weight........................................2.8 Kg DVD/VIDEO/SYSTEM Discs compatible...............DVD, VCD 1.0/1.1/2.0/3.0, MP3, CD, CD-R, CD-RW, PICTURE-CD Video System..................................AUTO / PAL / NTSC TFT/SYSTEM Resolution..................................800RGB(H) X 480(V)

  • Page 7: Basic Operation

    BASIC OPERATION 1. Tuning the unit On / Off Press the Power Button to turn the unit on. The opening screen of the unit will be showing on the TFT monitor. Press and hold the POWER button again to turn the unit off. 2.
  • Page 8 BASIC OPERATION 7. SETUP Enter the setup menu in the home screen by tapping the “SETTING” icon on the main menu. Tap the items you would like to set. You can adjust audio, date and time, language, cabibration, wallpaper,etc. 8. Day Light Saving Tap the Day button on the OSD to increase brightness.

  • Page 9: Radio Operation

    Radio Operation 1. Choose Radio Band Touch the AM button on screen to choose among the five radio bands - three FM Bands (FM1, FM2, and FM3) and two AM Bands (AM1, and AM2). Each of the five bands can store up to six preset stations, for a total of 30 preset memory stations. 2.

  • Page 10: Dvd/Vcd/Cd Operation

    DVD/VCD/CD Operation 1. Selecting Tracks Press the SEEK >>| Button to advance to the next track. Track numbers will be shown on the display. Press the SEEK >> to fast forward. Press the SEEK |<< Button to go to a previous track. Track numbers will be shown on the display. Press the SEEK << Button to fast reverse.
  • Page 11 DVD/VCD/CD Operation (Con’d) 8. Track Search Press the GOTO button to search the desired track to play the Disc. The OSD will be prompted. Make use of the navigation keys and digit keys on the touch screen to choose your desired chapter, track. Press the ENTER button to confirm your selection. 9.
  • Page 12 DVD/VCD/CD Operation (Con’d) 17. Electronic Skip Protection This unit is programmed with Electronic Shock Protection (ESP) so that the video will be protected against rough roads for 5 seconds. 18. Returning to Main User Interface Press the “BACK” button or “MENU” button to return to the main user interface. Mixed Disc / USB-SD Operation While you are playing mixed disc, USB, or SD card which contains MP3, WMA, JPG or DIVX formats, the unit will directly play the audio files.

  • Page 13: Bluetooth Operation

    Bluetooth Operation PAIRING At BT mode, search bluetooth device by the phone and “RDD802BT Caliber” will appear in your phone. Input “0000” as password to establish connection. DIAL PAD Touch the dial pad to dial the number you would like to call. Touch the CALL (green) button to send the number.
  • Page 14 Settings General Setting The general setting menu includes wallpaper, logo, Key Beep, radio region, RDS region, aspect ratio, warning, calibration. Time Setting You can select Date, Time, Time mode and Time zone by tapping > y l t B “ ”...

  • Page 15: Infrared Remote Control

    INFRA RED REMOTE CONTROL 1.Power on/off 16. Statistical Disc Information Display Button 2. Mode Select Key 17. Number Select Key MUTE 3.Play / Pause Function 18.Subtitle Language Switching Key BAND TITLE SUB-T 4.Mute Sound Function 19. Show All Track's Title (DVD only) ENTER SETUP 5.Band Select...

Table of Contents