Advertisement
Quick Links
28
50W
2 x
DUAL OUTPUT PROFESSIONAL
BALANCE CHARGER/DISCHARGER
For more information, please visit
www.RadientRC.com or scan the
QR code with your smart phone.
Part Numbers
RDNA0396 Duplex 2 x 50W LCD Charger, US
RDNA0397 Duplex 2 x 50W LCD Charger, UK
RDNA0398 Duplex 2 x 50W LCD Charger, EU
RDNA0399 Duplex 2 x 50W LCD Charger, AU
AC
DC
Entire contents ©2016 Radient RC.
1
Advertisement
Related Manuals for Radient Duplex RDNA0396
Summary of Contents for Radient Duplex RDNA0396
- Page 1 QR code with your smart phone. Part Numbers RDNA0396 Duplex 2 x 50W LCD Charger, US RDNA0397 Duplex 2 x 50W LCD Charger, UK RDNA0398 Duplex 2 x 50W LCD Charger, EU RDNA0399 Duplex 2 x 50W LCD Charger, AU Entire contents ©2016 Radient RC.
-
Page 2: Table Of Contents
Warranty and service....................27 Radient products are covered by the currently valid statutory warranty regulations. Radient and its authorised representatives accept no liability for loss, damage or costs which are caused by the incorrect or incompetent use of the product. For further information, please see the attached Warranty and Conformity document that is applicable to your territory. - Page 3 LiFe NiCd and NiMH battery charge/discharge and discharge/charge cycles Voltage level: 3.3V/cell Maximum charge voltage: 3.6V/cell You can set the charge and discharge sequence on the Allowable fast charge current: 4C or less left and the number of cycles on the right. You can Discharge voltage cut off level: 2.0V/cell or higher balance, refresh and break-in a battery using this...
- Page 4 There are a number of User Settings that can be adjusted The opening display shows the charger name to alter the default charger set-up. DUPLEX v1.0 for two seconds and any software revision. BY RADIENT RC The Duplex will then go straight to the main ENTER Start menu.
- Page 5 FOREWORD Warnings and error information continued Thank you purchasing the Duplex dual output, 50W per channel Balance The Duplex incorporates a variety of safety functions that verify the processes and Charger/Discharger. This product is a rapid charger with a high performance electronics.
- Page 6 In this program, the charger can measure DC Voltage. The I:12.1V O:19.87V caution and common sense, as failure to operate your Radient RC product in a safe input voltage is shown on the left. Connect a battery to the and responsible manner can result in damage to the product or surrounding property.
-
Page 7: Special Features
VERY IMPORTANT - PLEASE READ AND UNDERSTAND The top line of the display shows the drive current and The Radient Duplex charger has the capability of charging LiFe/Li-Ion/LiPo (LiXX), MOTOR 0.0A 19.87V voltage.The second line shows the output capacity (mAh) NiCd/NiMH (NiXX) and Lead Acid (Pb) batteries. -
Page 8: Special Features
SPECIAL FEATURES The voltage of each cell is shown in this display. Maximum Safety Delta-peak sensitivity: The automatic charge termination method is based on the 4>Set up DC power supply voltage and current principle of Delta-peak voltage detection. When the battery’s voltage exceeds the threshold, the charge process will be terminated automatically. -
Page 9: Connection Diagrams
Output 1 DC Input Cooling AC Input Balance Ports Output 2 1>Measure Internal Resistance Program In this program, the charger can measure the internal resistance of each individual cell. This feature is only available for lithium batteries. Use this program to measure the internal resistance of a lithium battery pack. -
Page 10: Warning And Safety Notes
WARNINGS AND SAFETY NOTES Discharging Pb batteries These warnings and safety notes are particularly important. For maximum safety, Set the desired discharge current on the left and nominal please follow these instructions. Failure to follow these instructions may cause voltage on the right. The current range is 0.1-2.0A. The damage to the battery or charger and at worst it may cause a fire. - Page 11 Voltage balancing and monitoring when discharging batteries Please check the following points before commencing charging: The processor monitors the voltage of each cell in the battery pack during the Have you selected the appropriate program suitable for the type of battery you are ‘storage’...
- Page 12 Discharging: The program has a maximum capacity protection feature. If the Delta peak voltage cannot be detected, the charge The main purpose of discharging is to clear the battery’s residual capacity, or to process will stop automatically when the battery reaches reduce the battery's voltage to a defined level.
-
Page 13: Program Flow Chart
Balancing Lithium batteries PROGRAM FLOW CHART The Duplex charger is set to the default user settings when it is connected to a power This function is for balancing the voltage of Lithium-polymer battery cells while source for the first time. The screen displays the following information in sequence and charging. -
Page 14: Discharging Lithium Batteries
The charge current reduces to 1/5 as the charge The screen shows the nominal voltage of a Lithium process reaches the end and has 1/10 remaining. The battery.The Duplex is capable of charging: LiFe (3.3V), charge capacity will reduce to that of normal charging, LiIo (3.6V) and LiPo (3.7V).