Audiovox Prestige APS-620 Installation Manual

Audiovox Prestige APS-620 Installation Manual

Audiovox remote start system installation manual
Hide thumbs Also See for Prestige APS-620:

Advertisement

This Remote Start System is designed to be used with
Automatic Transmission- Fuel Injection Vehicles Only!

COMPONENTS:

2 Four Button RF Transmitters
Antenna/Receiver
1 1" X 1.75" Foam Pad
6 Pin Main Power Harness
7 Pin Accessory Harness
1 Hood Pin Switch
1/4" Female Spade Connector

FEATURES:

-Selectable Ignition Lock & Unlock
-Selectable Door Lock/Unlock Output Timing
-Safe Start (Requires double push of the start button to engage the remote start
function)
-On-Board Parking Light Relay
-Trunk Release Output
-Horn Chirp Output With Selectable Duration
-Selectable RF Start Chirp
-Car Finder Mode (Can elect to have horn beep along with parking lights if
connected)
-Selectable Run Times 5, 10, 15, or 20 Minutes
-Selectable Gas or Diesel
-Automatic Start Timer (Can be set to start your car automatically at 2 or 4 hour
intervals)
-4 Negative Pulsed Aux Outputs Before Start, After Start, During Crank, After
Shutdown (To aid installation in many vehicles with factory alarm systems)
FCC NOTICE
This device complies with part 15 of the FCC rules. Operation of this device is subject to the
following conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may cause
undesired operation.
Caution: Changes or modifications not expressly approved by the party responsible for
compliance voids the users authority to operate this device.
Model APS-620
Installation Manual
2 Pin Door Lock/Unlock Harness
3 Pin Parking Light/Ground Harness
2 Pin LED Assembly
2 Pin Push-Button Valet/Program Switch
3 Pin Antenna Receiver Harness
4 Pin Auxiliary Output Harness
4 Philips Head Black Drill Point Sheet
Metal Screw #8 X 1/2"
Installation/Owners Guide
1
128-7829
1 of 12

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Prestige APS-620 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Audiovox Prestige APS-620

  • Page 1 (2) This device must accept any interference received, including interference that may cause undesired operation. Caution: Changes or modifications not expressly approved by the party responsible for compliance voids the users authority to operate this device. Model APS-620 Installation Manual 2 Pin Door Lock/Unlock Harness 3 Pin Parking Light/Ground Harness...
  • Page 2 INSTALLATION OF THE MAJOR COMPONENTS: CONTROL MODULE: Select a mounting location inside the passenger compartment (up behind the dashboard). The mounting location selected must be within 24" of the ignition switch wiring harness to allow connection of the 6 pin main wiring harness. Be certain that the chosen location will not interfere with proper operation of the vehicle.
  • Page 3 installed in all applications. Failure to do so may result in personal injury or property damage. Mount the switch in the hood locations away from water drain paths. If necessary, the included bracket may be used to move the switch away from rain gutters or allow mount- ing to the firewall behind the hood seal.
  • Page 4 the circuit and select the correct installation method. In addition you will realize why the connection of the safety wire is required for all mechanical switch con- figurations. Failure to make this connection properly can result in personal injury and property damage. In all installations it is the responsibility of the installing technician to test the remote start unit and ensure that the vehicle cannot start via RF control in any gear selection other than park or neutral.
  • Page 6 Wiring The 4 Pin Auxiliary Output Harness, Connector “A” The auxiliary 4 pin connector provides low current outputs to control various functions in the vehicle during different stages of the Remote Start unit's operation. Understanding these outputs and the time in which they occur will allow you to determine if they are needed for the particular vehicle you are working on as well as how to use them.
  • Page 7 3 Pin Antenna/Receiver, Connector “F” Route the 3 pin connector from the previously installed antenna receiver assemble to the mating connector on the control module. This connector supplies 5 volts, ground and RF data from the antenna receiver to the remote start module. Be certain this connector is firmly seated making good contact to the control unit.
  • Page 8 VEHICLE TO THE CONSUMER IF THIS CIRCUIT DOES NOT PERFORM AS SPECI- FIED. Green w/ Orange Trace Wire: Tachometer Input Signal This wire will continually monitor the engine's tach rate while the unit is under power of the Remote Start module. This wire will be routed to the vehicle ECM tach input or through the firewall into the engine compartment and connect to the negative side of the ignition coil.
  • Page 9 A. Shock Sensor By Pass: B. Additional Ignition Output: C. GM VATS Key Override: Green w/ White trace Wire: Entry Illumination Ground Output This wire provides a 30 second ground output (300 mA Max.) whenever the remote is used to disarm the alarm or to unlock the doors and provides a continuous pulsed output whenever the alarm is triggered.
  • Page 10 Setting Up The System Programming Features: Bank 1 Transmitter Channels Start with the system disarmed, turn the ignition switch to the on position then: 1) Press and release the push button valet/program switch 3 times. Siren Chirps once and or Lights flash one time indicating the transmitter program mode successfully entered.
  • Page 11 COMPLETING THE INSTALLATION: After you have confirmed the operation of the Audiovox Remote Start unit and tested all the safety features of the system: 1. Mount the control module up and behind the dash securing it in place with cable ties or screws.
  • Page 12 © 2006 Audiovox Electronic Corporation 150 Marcus Blvd, Hauppauge NY 11788 128-7829 128-7829 12 of 12...

Table of Contents

Save PDF