Related Manuals for Tytan DS410 CAN
Summary of Contents for Tytan DS410 CAN
- Page 1 You can afford the quality You can afford the quality tytan DS410 CAN manual for version 1141 and higher...
- Page 2 J2 - 7 J2 - 6 J2 - 6 J2 - 1 J2 - 1 J2 - 2 J2 - 2 J2 - 5 J2 - 5 J2 - 6 J2 - 6 tytan ds410 can tytan ds410 can tytan ds410 can...
- Page 3 EXAMPLARY OEM REMOTES close central locking open trunk open central locking (without trunk release button) (with trunk release button) IF THE EXTERNAL RF MODULE IN INSTALLED TYTAN DS410 CAN CAN BE ALSO CONTROLLED BY TYTAN REMOTE CONTROLS. DISARM DISARM DISARM DISARM...
- Page 4 Features of the tytan DS410 CAN vehicle security system • the VSS is controlled by OEM remote controls (vehicle's original equipment), up to 2 additional Tytan remote controls (*), • trunk release button logic (OEM remote), • monitoring of all doors, trunk, bonnet switches, •...
- Page 5 That state is confirmed by fast blinking of the LED. Closing the boot brings the security system again into the set state. IMPORTANT! This feature is car dependent. tytan ds410 can...
- Page 6 If enabled, then 8sec. after turning the ignition on (all doors closed) the central door lock will be locked (the doors can not be opened from the outside). Switching the ignition off unlocks the central door locking system. buttons on TYTAN remotes with the ignition on locks or unlocks the door locking system. Pressing the If the door locks are unlocked with the ignition on, then 8 seconds after opening and closing any passenger's door the central door locks will be locked again.
- Page 7 Tytan remote with the ignition on to lock central door locking system. Press the button on Tytan remote with the ignition on or switch the ignition off to unlock the central door locking system. These operations are not signalled by hazard lights nor siren nor LED.
- Page 8 The authorisation of anti-hijack function is confirmed by single 2 seconds pulse on LED. If the anti-hijack is not authorised and the ignition is switched on, the LED goes off and the VSS starts to wait for the RF transmission from Joker remote. tytan ds410 can...
- Page 9 GENERAL NOTES • tytan DS410 CAN Vehicle Security System (VSS) is intended to use in all combustion engine cars, with 12V supply system and negative ground. The tytan DS410 CAN security system must be installed according to the manufacturer’s requirements and documentation.
- Page 10 For some cars the orange wire becomes an input of additional +12V signals from car (e.g. trunk release actuator input) whereas the brown wire becomes an input of additional GND signal (e.g. door lock switch status signal). Always check the installation diagram for particular car! tytan ds410 can...
- Page 11 PROGRAMMABLE AND OPTIONAL FEATURES OF tytan DS410 CAN CAN bus control In some cars, the DS410 can control the vehicle electric systems via CAN bus - it can blink the direction indicators, roll-up windows and open/close central door locking system (with Tytan remote) via CAN bus.
- Page 12 (arming / disarming and central door lock control via Tytan remotes) The DS410 can be armed/disarmed by the Tytan remotes if the additional RF (radio receiver) module is connected to the rear connector of 2nd additional sensor. The RF module has two dedicated low-current negative control outputs.
- Page 13 Pic. 1. The screenshot of DS410 configuration software. tytan ds410 can...
- Page 14 The VSS has a dedicated service mode which has 5 stages: (1) reading and erasing the memory of 5 previous alarm cycles, (2) testing door, trunk and bonnet switches , (3) testing 2 additional sensor inputs, (4) testing and setting sensitivity of ultrasonic motion detector, (5) programming and testing of Tytan remotes. In order to enter the service mode Switch off the ignition.
- Page 15 After setting / testing ultrasonic motion detector, the service mode should be left by switching off the ignition, if the user did not want to erase / program / test Tytan remotes nor the RF module was not installed. Otherwise, press and hold the PA button for 3 seconds until siren chirps / LED blinks 5 times Stage V - testing and/or erasing/programming new remotes 5.1.
- Page 16 As long as the ignition is switched on, pressing any button on any programmed remote is signalled by 2 LED blinks and 2 siren chirps. Press the PA button 3 times to repeat programming new remotes (5.2) Switching off the ignition exits the transmitter testing mode and the service mode. tytan ds410 can...
- Page 19 17.02.2012 tytan ds410 can...
- Page 20 You can afford the quality You can afford the quality...
Need help?
Do you have a question about the DS410 CAN and is the answer not in the manual?
Questions and answers