Failure to follow these warnings and the assembly instructions could result in serious injury or death. • PLEASE SAVE OWNER’S • Strings can cause MANUAL FOR FUTURE USE. strangulation. DO NOT place items with a string • THIS PRODUCT REQUIRES around your child’s neck, ADULT ASSEMBLY.
Parts list This model may not include some features shown below. Check that you have all the parts for this model BEFORE assembling your product. If any parts are missing, call Customer Service. ALL MODELS Seat Assembly Leg Assembly Accessories Styles vary FEATURES ON CERTAIN MODELS...
Seat Assembly Make sure seat frame straps are not twisted or wrapped around the metal tubs. SNAP! Attach seat frame at the top of seat. SNAP! Attach seat frame at the bottom of seat.
Insert seat wire into the wire hole and channel on both sides. Insert the top of seat frame into seat pad. Wrap the pad around the bottom seat frame.
Attach the seat pad to the seat wire as shown. SNAP! Working from the outside in, snap the seat pad around the seat wire as shown. SNAP! SNAP!
Assembling Swing Frame Place carton on ground. Lay unit down as shown. Plug wires together as shown and insert wires inside tube. SNAP! Insert motor housing tubes to leg tubes as shown.
SNAP! Insert side base tubes into leg tubes as shown. SNAP! Insert front base tubes into side base tubes as shown.
Installing Seat Insert rectangle end of the hanger tube into motor housing. Repeat for other hanger tube. CHECK that hanger tube is secured in housing by pulling firmly on it. SNAP!
Insert hanger tube into seat mounts on sides of seat. Repeat for other hanger tube. CHECK that hanger tube is secured in housing by pulling firmly on it. SNAP!
To Secure Infant WARNING Falling Hazard: Always use the seat belt. Use slide adjuster at shoulder and waist for tighter adjustment. To change shoulder harness slots, see next page.
When changing harness strap slots, MAKE SURE harness straps are going through same slots in seat pad. The harness straps must go into the slot that is even with or slightly above the shoulders. Avoid twisting straps.
Installing Batteries (not included) WARNING To avoid injury: Remove child from swing before changing batteries. With baby out of swing, open the battery compartment lid by inserting a screwdriver into the coin slot. Insert four D (LR20-1.5V) cell batteries. CHECK that the batteries are put in correctly. Your swing will not run if the batteries are put in backwards.
For Safe Battery Use Keep the batteries out of children’s reach. Any battery may leak battery acid if mixed with a different battery type, if inserted incorrectly (put in backwards) or if all batteries are not replaced or recharged at the same time. Do not mix old and new batteries.
WARNING Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user authority to operate the equipment. NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
To Use Wall Plug WARNING Product does not recharge batteries. When AC adapter is in use, batteries will automatically shut off. DO NOT place product near water and moisture. Do not use the product near possible wet areas, such as a bathtub, shower, wash basin, sink, laundry tub, swimming pool, wet basement, etc.
Starting Swing (6 Speed) Battery Low Alert Speed Selection 1-6 Music Volume up Music off Volume down Soothing sounds WARNING avoid serious injury from falling or sliding out. Always use seat belt. After fastening buckles, adjust belts to get a snug fit around your infant. TO TURN SWING ON: Rotate the speed dial clockwise, and lightly push the swing to get it started.
(Music) Selects music. All ten songs will play in turn and then start again with the ﬁ rst song. Skip a song by pressing the button. Music will automatically shut off 60 minutes after the last button press or speed change.
Features on Certain Models This model may not include some features. DO NOT use any other accessories with this product. Head support Styles vary Only use this head support on this swing. Never use this head support on any other product.
To Use Vibration Remove battery lid, found under seat, with a key and insert 1-D (LR20-1.5V) battery in module. Replace lid. Vibration: Turn to one of two settings.
Problem Solving SWING WON’T OPERATE: 1. No batteries in swing. 2. Batteries dead. 3. Speed setting too low. 4. Batteries in backwards — check “+” and “-”. 5. Corrosion on battery terminals. Rotate batteries in place against terminals, or clean with sandpaper or steel wool if corrosion is severe.
• FROM TIME TO TIME CHECK YOUR SWING for loose screws, worn parts, torn material or stitching. Replace or repair the parts as needed. Use only Graco replacement parts. • TO CLEAN SEAT COVER, Refer to your care tag on your seat pad for washing instructions.