Advertisement
Table of Contents
- 1 Specifications
- 2 Attention to be Paid at the Time of Installation
- 3 Attention to be Paid at the Time of Using
- 4 Procedure of Usage
- 5 At the Time the Operation Is over
- 6 The Holding’s Adjustment
- 7 How to Prevent and Adjust Roller Moiré (Puckering)
- 8 How to Move the Machine by Hand at the Emergency
- 9 Cleaning Belts
- 10 Cleaning the Cleaner
- 11 Cleaning the Brush Scraper
- 12 Cleaning the Rotary Strip off Blade
- 13 How to Exchange Upper Belt
- 14 How to Change Lower Belt
- Download this manual
Advertisement
Table of Contents
Related Manuals for HASHIMA HP-450CS
Summary of Contents for HASHIMA HP-450CS
- Page 1 HASHIMA HASHIMA COMPACT PRESS HP-450C/CS INSTRUCTION MANUAL HASHIMA CO.,LTD...
- Page 2 SPECIFICATIONS MODEL HP-450C/CS POWER SUPPLY 1P-220V RATED OUTPUT HEATER ４．５KW MOTOR ４０W TEMPERATURE A(MAX) ２００℃ PRESSURE (MAX) １．５KG/cm BELT SPEED ８．７ｍ／min. HEATING TIME ５ − ２０ sec. FUSING WIDTH ４５０ｍｍ DEMENTIONS １６６０ｍｍ ８８０ｍｍ ４９０ｍｍ WEIGHT １５２ｋｇ...
- Page 3 Attention to be paid at the time of installation 1. Install this machine, which weights 152kg, in regard to the 450C/CS respectively, on the robust foundation horizontally. 2. Don’t install this machine near the object easy to burn, as it generates high temperature when it has been put into use.
- Page 4 9. Don’t fail to pull the power source plug off when you inspect the inside. 10. This machine is an exclusive use for fusing and folding the clothes. Don’t put it to use for other purposes, otherwise resulting in troubles. 11.
- Page 6 Procedure of usage 1. Set the power source to ‘ON’.(Ensure the ‘off ’ condition of the timer switch.) 2. Press the start button. The lamp will light up and the machine will start moving. 3. Set pressure to the designated by using the pressure adjust knob. 4.
- Page 7 How to prevent and adjust roller moiré (puckering) In the case where roller moiré has taken place on the fused material, fuse it by lowering heat and pressure as low as possible. Even when the prevention is impossible in spite of the efforts, adjustments to be shown below will be necessary.
- Page 8 –in.>> Cleaning belts Clean the belt while it is hot. Use the Hashima New Ace or the New Clean Spray to clean the belt. In the case where you put the latter to use . pay attention not to spray such electric parts as the warp prevention limit switch and others, resulting in troubles.
- Page 9 ATTENTION TO BE PAID MAINTANANCE OF FUSING MACHINE Put-off electric sources, fill “grease” inside rollers every two weeks You should use HASHIMA genuine grease and never use grease which contains MOLYBDENUM (LACK OF THIS GIVES DAMAGES TO BEARINGS) 1. TAKE OUT MAIN COVER A.
- Page 11 上ベルト交換方法 HOW TO EXCHANGE UPPER BELT 次頁参照 Refer next page...
- Page 12 1． 電源ブレーカーを切り、圧力調整ツマミで圧力を−１にし、くわえ込み調整を０にしてくだ さい。 Disconnect the power source from its origin and set the pressure –1, and pull-in adjuster set to 0. ２．本体カバー（A）を持ち上げて外してください。本体カバー（パネル側）のネジを外し、近 くに置くか、パネル側の線をコネクターから外し操作ボックスを取り外してください。 Take off main cover (A). Take off screw of main cover (panel side) and put it near the machine or take off connector of panel side and control box.
- Page 13 ９．上フレームの外側を通し、ベルトを抜いて下さい。 上ベルトを交換する場合、フレームスペーサーを外した方が楽に交換できます。 ただしその場合、前テーブル、作業テーブル、補助フレーム、ベルト保護ステー、 左側補強ステーを外してください。 （外し方は下ベルト交換方法参照） Take off a belt from upper frame. When change upper belt, it is easier by taking off frame spacer. In this case, take off front table, working table, sub-table, belt protection stay and Left frame support stay. (Refer how to change lower belt) １０．組立は分解の逆の手順で行ってください。...
- Page 15 下ベルト交換方法 How to change lower belt.
- Page 16 １．電源ブレーカーを切り、圧力調整つまみで圧力を−１にしてください。 又、くわえ込み調整を０にしてください。 Disconnect the power source from its origin and set the pressure to -1 by the pressure adjusting knob. Set the holding’s adjustment to 0. ２．作業テーブルを外してください。 Take the front table off. ３．作業テーブル補助フレームを外してください。 Take the front table stay off. ４．ベルト保護ステーを外してください。さら子ネジ ２本 （黄色） Take the belt protection stay off.
- Page 17 Take the tension roller (lower) off. １３．ハケステー（下）を外してください。 Take the blade stay (lower) off. １４．フレームスペーサーを外してください。 六角ボルト ３本 （黄色） Take the frame spacer off. Hex. Bolt 3 (yellow mark) １５．ベルトを下フレームの外側から通し、抜いてください。下ベルトを交換する場合、 上側カバーを外した方が楽に交換できます。 Press the belt through the outside of the lower frame in order to pull it out. When change lower belt, it is easier by taking off upper cover.