Table of Contents
Advertisement
page 1
SAFETY PRECAUTIONS CONTINUED...
EMF Information
Considerations About Welding And The Effects Of Low Frequency
Electric And Magnetic Fields
Welding Current, as it flows through welding cables, will cause
electronic magnetic fields. There has been and still is some concern
about such fields. However, after examining more than 500 studies
spanning 17 years of research, a special blue ribbon committee of
the National Research Council concluded that: "The body of evidence,
in the committee's judgment, has not demonstrated that exposure
to power frequency electric and magnetic fields is a human-health
hazard." However, studies are still going forth and evidence continues
to be examined. Until the final conclusions of the research are
reached, you may wish to minimize your exposure to electromagnetic
fields when welding or cutting.
To reduce magnetic fields in the workplace, use the following
procedures:
1.
Keep cables close together by twisting or taping them.
2.
Arrange cables to on side and away from the operator.
3.
Do not coil or drape cables around your body.
Introduction
Thank you for choosing Bernard. The product you have purchased has
been carefully assembled and factory tested prior to shipment. Should
you experience problems with installation or performance, please refer
to the "Troubleshooting Guide" in this manual.
Before installing, compare the equipment received against the invoice
to verify that the shipment is complete and undamaged. It is the
responsibility of the purchaser to file all claims of damage or loss that
may have occurred during transit with the carrier.
The manual contains general information on the operation of this
Bernard product. Before installing or operating any equipment, read
and understand the information and safety precautions presented
in this manual. Also, note the various data plates, labels, and tags
attached to the product.
While every precaution has been taken to assure the accuracy of this
manual, Bernard assumes no responsibility for errors or omissions.
Bernard assumes no liability for damages resulting from the use of
the information contained herein. Bernard shall have no liability to
the buyer for consequential damages or be liable to the in tort for
any negligent manufacture of the goods or for the omissions of any
warning therefrom.
Part I General Description
The Bernard PipeWorx MIG Gun is designed primarily for process-
ing mild steel electrode under GMAW (Gas Metal Arc Welding), MIG
(Metal Inert Gas), MAG (Metal Active Gas), FCAW (Flux Cored Arc
Welding), and MOG (Metal without Gas).
The PipeWorx MIG Gun provides rapid neck interchangeability, typi-
cally during production processes. Neck may also be positioned on
line within a 360 degree rotation. This position allows for movements
between standard horizontal welding, overhead, and hard-to-reach
side angles. The neck includes an optional jump liner system that
effectively reduces costs associated with one-piece liner systems.
Bernard is concerned about your higher productivity.
4.
Keep welding power source and cables as far away from operator
as practical.
5.
Connect work clamp to workpiece as close to the weld as
possible.
About Pacemakers:
Pacemaker wearers consult your doctor first. If cleared by your
doctor, them following the above procedures is recommended.
California Proposition 65
Warning
Welding or cutting equipment produces fumes or gases which contain
chemicals known to the State of California to cause birth defects and
in some cases, cancer. (California Health and Safety Code Section
25249.5 et seq.) This product contains chemicals, including lead,
known to the state of California to cause cancer, and birth defects or
other reproductive harm. Wash hands after use.
Commercial Warranty
Product is warranted to be free from defects in material and
workmanship for 1 year after the sale by an authorized Buyer. Straight
handles, straight handle switches and straight rear strain reliefs are
covered by a lifetime warranty.
Bernard reserves the right to repair, replace or refund the purchase
price of non-conforming product. Product found not defective will be
returned to the Buyer after notification by Customer Service.
Bernard makes no other warranty of any kind, expressed or implied,
including, but not limited to the warranties of merchantability or fitness
for any purpose. Bernard shall not be liable under any circumstances
to Buyer, or to any person who shall purchase from Buyer, for
damages of any kind. Including, but not limited to any, direct, indirect
incidental or consequential damages or loss of production or loss of
profits resulting from any cause whatsoever, including, but not limited
to, any delay, act, error or omission of Bernard.
Genuine Bernard parts must be used for safety and performance
reasons or the warranty becomes invalid. Warranty shall not apply
if accident, abuse, or misuse damages a product, or if a product is
modified in any way except by authorized Bernard personnel.
The PipeWorx MIG Gun meets or exceeds NEMA (National Electrical
Manufacturer's Association) EW3 requirements for guns used in a
wide variety of applications including aluminum, silicone bronze, and
hard facing alloys to name a few. With Bernard's flexibility, many ap-
plications can be accommodated with field installed options increasing
performance and maneuverability.
Advertisement
Table of Contents
