Table of Contents
Advertisement
Digital Multi-channel sound
Digital multi-channel connection provides the best sound
quality. For this you need a multi-channel A/V receiver that
supports one or more of the audio formats supported by
your DVD player (MPEG 2, Dolby Digital™ and DTS).
Check the receiver manual and the logos on the front of
the receiver.
AMPLIFIER
G
F
A
MULTICHANNEL AUDIO OUT
LEFT
CENTER
LEFT
REAR
FRONT
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
MAINS
RIGHT SUBW.
RIGHT
OPT OUT
DIG OUT
REAR
FRONT
Note:
– If the audio format of the digital output does not match the
capabilities of your receiver, the receiver will produce a strong,
distorted sound or no sound at all.
– The selected audio format of the DVD is displayed in the
Status Window when the SYSTEM MENU is activated or Audio
button is activated.
– Six Channel Digital Surround Sound via digital connection
can only be obtained if your receiver is equipped with a Digital
Multi-channel decoder.
– To see the selected audio format of the current DVD in the
Status Window, press the SYSTEM MENU or the Audio
Language selector button.
Cinemalink (on SCART)
This DVD player is equipped with cinemalink feature (from
Philips) which allows a more complete control of your
home audio/video (AV) equipment.
Cinemalink interconnection plug & playback will enable the
AV system to recognise the users intention and
automatically switch the necessary controls or input source
accordingly. This will reduce the necessity of having multiple
control inputs for all AV equipments (eg. TV and Amplifier).
TV
X
Y
Z
I
Y
C
C
B
R
AUX/VCR
IN
II
TV OUT
L
(CVBS)
(Y/C)
R
AUDIO OUT
VIDEO OUT
S-VIDEO OUT
Analog connection to a multi-channel A/V
receiver with 6 CH connectors
This DVD player contains a multi-channel decoder. This
enables playback of DVDs recorded in Multi-channel
Surround without the need for an optional decoder.
1
Connect the audio out jacks for Center speaker and
Subwoofer connection (C) to the corresponding in jacks on
your receiver.
2
Connect the audio Left and Right out jacks for Front
speaker connection (B) to the corresponding in jack
sockets on your receiver.
3
Connect the audio Left and Right out jacks for Surround
speaker connection (D) to the corresponding in jacks on
your receiver.
4
Make the appropriate Sound settings for Analog Output
and Speaker Settings in the Personal Preferences menu.
AMPLIFIER
D
DIGITAL AUDIO OUT
PCM/MPEG2/AC3/DTS
MAINS
OPT OUT
DIG OUT
NTSC/PAL Settings
You can switch the NTSC/PAL setting of the DVD player to
match the video signal of your TV. This setting only affects
the television's on-screen display that shows the stop and
setup modes. You may select either NTSC or PAL. To
change the DVD player setting to PAL or NTSC, follow the
steps below.
1
Unplug the DVD player from the mains.
2
Press and hold 9 and SOUND, on the front of the DVD
player. While holding 9 and SOUND, plug in the mains.
3
After PAL or NTSC appears on the display panel of the
DVD player, release 9 and SOUND, at the same time.
The PAL or NTSC that appears on the display panel
indicates the current setting.
4
To change the setting, press SOUND, within three
seconds. The new setting (PAL or NTSC) will appear on the
display panel.
TV
C
B
X
Y
Z
MULTICHANNEL AUDIO OUT
I
LEFT
CENTER
LEFT
Y
C
B
C
R
AUX/VCR
REAR
FRONT
IN
II
TV OUT
R
L
(CVBS)
(Y/C)
RIGHT
SUBW.
RIGHT
AUDIO OUT
VIDEO OUT
S-VIDEO OUT
REAR
FRONT
P
REPARATION
11
Advertisement
Table of Contents
