Download Print this page

aci snowsport User Manual

Hd utility plow
Hide thumbs Also See for snowsport:

Advertisement

Quick Links

www.mysnowsport.com
If you find a part, or parts missing or defective, or if you're having trouble
installing your new plow, please have serial number ready (found on
decal on back of blade) and call the customer service number
701-251-1427. It is recommended that you take the time to review
all the material in this manual, even if already familiar with the
product, because often changes are made without prior notice.
ATTENTION OWNERS AND OPERATORS:
SAVE THIS INSTALLATION/OPERATORS MANUAL. READ AND FOLLOW THE
OPERATING AND SNOW PLOWING PRACTICES. PLEASE HAVE SERIAL NUM-
BER AVAILABLE (FOUND ON DECAL ON BLADE) IF CALLING FOR CUSTOMER
SERVICE ASSISTANT.
Promptly confirm your warranty registration on-line at www.agricover.com.
BASIC SNOWPLOWING PRACTICES
The SNOWSPORT utility plow was designed to make moving snow convenient and
easy, and by following some simple tips, snow removal can be a safe, enjoyable experi-
ence. Always keep current with the snowfall. It's easier to plow fresh snow. Wet snow
can compact and freeze which requires chipping to break it loose before attempting to
move it. From the start of the season push the snow far enough out to allow for future
snowfalls. Avoid overloading your equipment - push only enough snow with each pass
to get the job done. To start a pass, accelerate slowly - allowing for tire traction and
blade to accumulate snow. As you come to the end of a pass, lift off the accelerator and
start applying brakes as needed. If snow is deep and/or compacted you may need to go
over it two or three times.
When pushing snow up to hardened snow piles – DO SO STRAIGHT-ON – NOT
AT AN ANGLE.
Always know the terrain before plowing
When transporting blade, secure it to retainer brackets with snap pins
Do not exceed 65 MPH when transporting plow
Do not exceed 10 MPH when plowing
Always wear your seat belt when plowing
Never plow with your head out of the window – an unexpected sudden stop could
result in personal injury
When backing up don't rely on rear view mirrors – turn around and look where you
are going
Never pile snow on someone elses property, on street or sidewalks, by fire
hydrants, mailboxes, water drains or electrical boxes
Check with local regulations before pushing snow across roads – it may be illegal
Do not pile snow near handicapped or parking areas
Plow snow during low-traffic hours – be cautious of pedestrians, domestic animals
and vehicles
Never pile snow where it obstructs visibility of traffic
Remember – always exercise safety, courtesy, and common sense
On 4WD select low range
On manual transmission - avoid riding clutch
Watch engine heat gauge and avoid overheating
Follow vehicle manufacturers specifications for snowplowing
©Copyright 2008 AGRI-COVER, INC. All rights reserved. U.S. Patent No. 6,817,118 and other patents pending.
IMPORTANT
Part No. 30505 REV:E
FOR YOUR RECORDS:
DATE PURCHASED_______________________________________
WHERE PURCHASED_____________________________________
SERIAL NUMBER ________________________________________
(Located on decal on back of blade)
MANUFACTURER'S LIMITED WARRANTY
Agri-Cover, Inc. extends the following limited warranty on its SNOWSPORT Utility Plow
to the original retail purchaser of any SNOWSPORT Utility Plows purchased after
October 1, 2007:
Agri-Cover, Inc. warrants its SNOWSPORT Utility Plow to be free from defects in mate-
rial and workmanship under normal use for three (3) years from date of purchase.
ANY IMPLIED WARRANTY APPLICABLE TO THE SNOWSPORT UTILITY PLOW IS
LIMITED IN DURATION TO THREE YEARS FROM THE DATE OF PURCHASE. Agri-
Cover's sole obligation under this warranty or any implied warranty is limited to the
repair or replacement at its option, of defective parts only. No labor or service
allowance is given or implied. IN NO EVENT SHALL AGRI-COVER, INC. BE LIABLE
FOR INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES. Some states do not
allow limitations on how long an implied warranty lasts or exclusions of incidental or
consequential damages, so the above limitations and exclusions may not apply to you.
For warranty performance call our Customer Service Department at 701-251-1427 to
determine if only a replacement part is needed or if the product needs to be returned
for inspection and repair. Warranty registration must be on file and/or proof of orig-
inal purchase (detailed and dated receipt) required for warranty to be effective.
Goods to be returned must have a pre-authorized FA # (Returned Authorization
Number) – obtained by calling the number above. Mark the number on the pack-
age and ship it freight prepaid to address below. Agri-Cover will pay freight to return
goods to sender.
This limited warranty does not cover any failure due to abuse, misuse, alteration, neg-
lect, improper assembly or installation, or improper maintenance.
This limited warranty gives you specific legal rights and you may have other rights
which vary from state to state.
082508TR1000
Agri-Cover, Inc.
Customer Service Dept.
3000 Hwy. 281 SE, PO Box 508
Jamestown, ND 58402
Phone (701) 251-1427

Advertisement

loading

Summary of Contents for aci snowsport

  • Page 1 Agri-Cover, Inc. warrants its SNOWSPORT Utility Plow to be free from defects in mate- move it. From the start of the season push the snow far enough out to allow for future rial and workmanship under normal use for three (3) years from date of purchase.
  • Page 2 Parts Diagram Lift Handle #10573 Slide Hinge 3/8 x 3/4” Bolt #60291 #10183 Blade Marker Kit Flat Washer #40685 #10185 3/8 x 3/4” Bolt Keyhole Pin #10183 #30489 Square Nut 3/8” Self 1/2 x 3-1/2” Bolt #30512 #10172 Threading Bolt With Lock Nut #20534 #10893 Leveling Shim #10591...
  • Page 3 Blade Marker End Plate Slide Hinge section of aluminum blade Bottom section of aluminum blade Tip: apply soapy water solution to Use 2x4 to prop Tongue parts for easier bottom of blade up assembly. at both ends groove Rubber Blade joint Box End b) Align end of rubber edge with...
  • Page 4 3/16 drill bit #3 Phillips self drilling screw Factory mark (4x) Ends flush a) At bottom of blade (where rubber is inserted, check to make sure b) Using Phillips #3 bit, run a self drilling screw into each of the ends are flush), then drill a 3/16 inch pilot hole at factory mark in four pilot holes.