Table of Contents
Advertisement
Quick Links
ELECTRIC PLOW WINCH
INSTALLATION INSTRUCTIONS
Thank you for purchasing SNOWSPORT
Electric Plow Winch for your SNOWSPORT
TM
®
HD or LT Utility Plow. Agri-Cover, Inc. proudly manufactured this winch using superior
quality materials and workmanship. With proper care, your winch will provide years of
service and enjoyment.
NOTICE TO INSTALLER: Even if familiar with hardware, read instructions prior to
installation as improvements may be made without notice. Always handle components
with care. If you have questions or problems, have serial number ready and call
customer service. When done, these instructions must be given to the consumer.
NOTICE TO CONSUMER: Before using snowplow, read safety and operation sections.
Save these instructions for future reference.
FOR YOUR RECORDS
DATE PURCHASED:
WHERE PURCHASED:
SERIAL NUMBER:
(Located on switch box)
Questions? 800-689-6612
agricover.com
Advertisement
Table of Contents
Related Manuals for aci SNOWSPORT
Summary of Contents for aci SNOWSPORT
- Page 1 ELECTRIC PLOW WINCH INSTALLATION INSTRUCTIONS Thank you for purchasing SNOWSPORT Electric Plow Winch for your SNOWSPORT ® HD or LT Utility Plow. Agri-Cover, Inc. proudly manufactured this winch using superior quality materials and workmanship. With proper care, your winch will provide years of service and enjoyment.
-
Page 2: Safety Information
PREPARATION SNOWSPORT Electric Plow Winch works on new and prior SNOWSPORT HD and LT ® models with a 4 bolt push frame. Unpack electric plow winch components. For additional installation assistance, go to mysnowsport.com for install and operation videos. COMPONENTS TOOLS NEEDED •... -
Page 3: Snowplowing Tips
• As you come to the end of a pass, reduce speed and apply brakes as needed • When creating piles with a SNOWSPORT HD Utility Plow, drive straight with the ®... -
Page 4: Parts Diagram
PARTS DIAGRAM Bow-tie pins Winch cover Synthetic cable Control box Front plate Motor Base Cleat... - Page 5 1: INSTALLING WINCH TO PUSH FRAME To install winch, perform one of the following. Winch assembly NEW PLOW ASSEMBLY A. Complete provided HD or LT Plow instructions. Push frame RETROFIT PLOW A. Note placement of bolts with hardware and shims (if applicable) for later reinstallation. Remove (4) bolts with hardware connecting push frame to interceptor.
- Page 6 2: INSTALLING CLEAT Perform one of the following to install cleat, then continue to step 2A. NEW PLOW ASSEMBLY Completed in HD or LT Plow instructions. (2) Weld nuts Top channel RETROFIT PLOW Tilt (2) weld nuts into top channel with flat side up at mid-point on blade.
- Page 7 3: ATTACHING WINCH COVER A. Attach winch cover to winch assembly with Bow-tie pins (2) bow-tie pins. 4: INSTALLING WIRES CAUTION: Disconnect power before Quick connect plug working with electrical system or components. Circuit breaker A. Run main power wire to battery. Ensure quick connect plug on main power wire will reach plug on winch without interference, adjust as needed.
- Page 8 4: INSTALLING WIRES (Continued) C. Starting from winch assembly, run cab wire Cab switch Primer Tether to a rigid location. Quick wires connect IMPORTANT: Ensure safe wiring path. plug Avoid sharp edges, moving parts and hot components. switch wire NOTE: For best adhesion, ensure air and Crush at surface temperatures are above 60°...
- Page 9 4: INSTALLING WIRES (Continued) H. Attach fastener on cab switch to fastener at cab location. NOTE: Do not remove switch for at least 48 hours to allow adhesive to cure. I. Attach quick connect plug on main power wire to winch plug and test system's operation with control box located on back of winch.
-
Page 10: General Troubleshooting
GENERAL TROUBLESHOOTING Check all wiring components. A. Check positive (+) and negative (-) wire connections on vehicle battery. B. Retighten loose connections. C. Replace any corroded connections. D. Check all wires for worn or bare spots. E. Verify 12 volts or more come into the electric winch when operating. - Page 11 TO STORE BLADE DURING OFF SEASON For maximum blade life, periodically retighten bolts and protect blade from sun by storing inside or covering. NOTE: When pushing snow onto a pile with a SNOWSPORT HD Utility Plow, always ® do so with blade set to center position. Piling snow with blade angled may cause damage to plow or vehicle.
-
Page 12: Manufacturer's Limited Warranty
MANUFACTURER’S LIMITED WARRANTY Agri-Cover, Inc. extends the following Limited Warranty on its SNOWSPORT Electric Plow Winch Agri-Cover, Inc. warrants its SNOWSPORT Electric Plow Winch to be free from defects in material and workmanship under normal use for one (1) year from date of manufacture unless accompanied by proof of purchase.This limited warranty does not cover any failure...