Table of Contents
Related Manuals for The Handy THHMR
Summary of Contents for The Handy THHMR
- Page 1 OPERATOR’S MANUAL AND PARTS LIST 12” HAND PUSH ROLLER MOWER - THHMR Sales & Helpline 01793 333220 www.thehandy.co.uk Before use please read & understand this manual, paying particular attention to the safety instructions. 2010 v1 Page 1...
-
Page 2: Table Of Contents
Contents DIAGRAM SAFETY INSTRUCTIONS AND PREPARATION ASSEMBLING THE MACHINE AND GRASSBAG ADJUSTING THE BOTTOM (FIXED) BLADE ADJUSTING THE CUTTING HEIGHT ADJUSTING THE DELIVERY PLATE ADJUSTING THE CHAIN MAINTENANCE PARTS DIAGRAM PARTS LIST Page 2... -
Page 3: Diagram
DIAGRAM Page 3... -
Page 4: Safety Instructions And Preparation
SAFETY INSTRUCTIONS AND PREPARATION • Read and understand this owner’s manual before assembly and use. Learn its application and limitations as well as the specific potential hazards. Retain these instructions for reference. • Retain all the packaging until you are sure that the product is operating correctly. • Take care with the sharp cutting blades. It is recommended that gloves are worn when unpacking, assembling, adjusting and maintaining the lawnmower. • This lawnmower is for mowing lawns only and for domestic, not commercial use. • Never allow children or people unfamiliar with these instructions to operate the mower. • Inspect the area where the lawnmower is to be used and remove all stones, sticks, wires and other debris or foreign bodies. • Never place your hands, fingers or feet near the cutting blade when the lawnmower is moving. • Do NOT operate the mower whilst barefoot or wearing sandals. • Walk slowly during use – do NOT run. • Do NOT use when the grass is wet enough to be slippery. -
Page 5: Assembling The Machine And Grassbag
ASSEMBLING THE MACHINE AND GRASSBAG You will need a Phillips screwdriver and a 10mm spanner. Take care when fitting the lower handles because of their proximity to the cylinder blade. We recommend the use of gloves. • Align the two holes on both of the upper handle with those on the handle extensions, Secure them using the wignuts and screws provided. Repeat the process with the lower handle. • Attach the assembled handle with one lower handle, by locating onto the pegs within the main body recessed slots on each side of the mower. Repeat the process with the other lower handle. To assemble the grassbag:- • Insert the two side frames separately into the holes of the clip on the front piece. • Insert the single wire into the holes at the back of the side frame. • Slip the fabric bag onto the wire frame and clip snap the plastic bars around the edge of the frame. -
Page 6: Adjusting The Bottom (Fixed) Blade
ADJUSTING THE BOTTOM (FIXED) BLADE This operation needs to be done whilst carefully turning the cylinder blade. We recommend the use of gloves. • The bottom fixed blade must be set correctly in order for the lawnmower to work efficiently. Using the spanner supplied, slacken off the two top nuts on each side of the side casing. Carefully tighten the two adjusting knobs (A) by turning them slowly in a clockwise direction. • When the cylinder blade just makes contact with the bottom blade, turn the knobs slightly in an anti-clockwise direction until the cylinder blade turns without touching the bottom blade. Tighten up the nuts on the side casing. ADJUSTING THE CUTTING HEIGHT • The mower can be set at to cut at any height betweeen 13mm and 23.5mm. Adjust the height of cut by loosening the two knobs on the side of the cutting height roller and moving the roller up and down to the required height. • Remember to adjust both sides of the roller equally otherwise the lawnmower will not give an even cutting finish. ADJUSTING THE DELIVERY PLATE If the grass is not being thrown into the bag satisfactorily, then the delivery plate can be adjusted. • Slacken the two screws (A) • Underneath this cover you will see the delivery plate with projections at either side. Move these projections backwards or forwards until better results are achieved. The delivery plate must not touch the cutting cylinder. •... -
Page 7: Maintenance
MAINTENANCE After each use remove all grass clippings that may have collected in and around the wheels, roller and blades. We recommend a regular application of oil or lubricant (i.e. WD-40). This should be applied to all cutting surfaces, the cutting reel axle shaft and roller and will keep your lawnmower in tip-top condition. Page 7... -
Page 8: Parts Diagram
PARTS DIAGRAM Page 8... -
Page 9: Parts List
PARTS LIST No Part No Description Part No Description TH133-1 Chain Cover Case TH133-2 Bolt TH133-3 Washer TH133-4 Lock Nut TH133-5 Chain TH133-6 Sprocket Wheel Assy TH133-7 Lock Nut TH133-8 Washer TH133-9 Small Sprocket Wheel TH133-10 Carriage Bolt TH133-11 Chain Adjuster TH133-12 Hex Head Bolt TH133-13 Knob TH133-14 Hex Head Bolt TH133-15 Left Side Plate Assy TH133-16 Right Side Plate Assy TH133-17... - Page 10 HANDLE DIAGRAM AND PARTS Post 2010 Models Pre 2010 Models Part No Description TH133-45 Bolt TH133-46 Wing Nut TH133-47 Centre Handle TH133-48 Lower Handle TH133-49 Top Handle TH133-50 Handle Grip TH133-51 Washer TH133-52 Wing Nut TH133-53 Lower Handle TH133-54 Centre Handle TH133-55 Upper Handle TH133-56 Foam Grip TH133-57 Foam Grip Plug TH133-58 Bolt M5x45 TH133-59 Bolt M6x55 Page 10...
- Page 11 To order spare parts and see the complete range of garden machinery and garden equipment from Handy, visit: www.thehandy.co.uk Page 11...