Panasonic HDC-SDT750PP Service Manual page 54

Service Manual
Diagrams and Replacement
Parts List
High Definition Video Camera
Model No.
HDC-SDT750PP HDC-TMT750GC
HDC-SDT750EB HDC-TMT750GD
HDC-SDT750EE HDC-TMT750GK
HDC-SDT750EF HDC-TMT750GT
HDC-SDT750EG
HDC-SDT750EP
HDC-SDT750GC
Vol. 1
Colour
(H)...........Gray Type
Table of contents
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Flash P.C.B. .......................................................................... S-2
S2.2. BATT_Catcher P.C.B. ............................................................ S-2
S2.3. Front P.C.B. ........................................................................... S-2
S2.4. MIC AMP P.C.B. .................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Flash Schematic Diagram ..................................................... S-5
S4.3. BATT_Catcher Schematic Diagram ...................................... S-6
S4.4. Side R Schematic Diagram ................................................... S-7
S4.5. Monitor Schematic Diagram .................................................. S-8
S4.6. Front Schematic Diagram ..................................................... S-9
S4.7. MF SENS Schematic Diagram ............................................ S-10
VM1009043CE
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as "
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
S4.8. MF Hole FPC Schematic Diagram ...................................... S-10
S4.9. CAM FUNC FPC Schematic Diagram................................. S-11
S4.10. EVF B/L Schematic Diagram ............................................ S-11
S4.11. MIC AMP Schematic Diagram ........................................... S-12
S4.12. MIC AMP FPC Schematic Diagram .................................. S-13
S5. Print Circuit Board .................................................................. S-14
S5.1. Flash P.C.B. ........................................................................ S-14
S5.2. BATT_Catcher P.C.B. .......................................................... S-15
S5.3. Side R P.C.B. ...................................................................... S-15
S5.4. Monitor P.C.B. ..................................................................... S-16
S5.4.1. Monitor P.C.B. (Component Side) .................................... S-16
S5.4.2. Monitor P.C.B. (Foil Side) ................................................. S-17
S5.5. Front P.C.B. ......................................................................... S-18
S5.6. MF SENS P.C.B. ................................................................. S-18
S5.7. MF Hole FPC P.C.B. ........................................................... S-19
S5.8. CAM FUNC FPC P.C.B ....................................................... S-19
S5.9. EVF B/L P.C.B. .................................................................... S-20
S5.10. MIC AMP P.C.B. ................................................................ S-20
S5.11. MIC AMP FPC P.C.B. ........................................................ S-21
S-1
" mark.
Circuit name being connected.
This signal is connected
OFTR FEP
to the FEP schematic diagram.
Name of Signal
S6. Replacement Parts List .......................................................... S-23
S7. Exploded View ....................................................................... S-34
S7.1. Frame and Casing Section (1) ............................................ S-34
S7.2. Frame and Casing Section (2) ............................................ S-35
S7.3. EVF Section ........................................................................ S-36
S7.4. LCD Section ........................................................................ S-37
S7.5. Lens Section ....................................................................... S-38
S7.6. Packing Parts and Accessories Section .............................. S-39
S7.7. Conversion Lens Section .................................................... S-40
HAVE THE SPECIAL CHARACTERISTICS