Table of Contents
Advertisement
Operating Instructions tico 735 - Elapsed Timer
Introduction
Your Hengstler tico 735 Elapsed Timer is one model in a family of 1/8 DIN units which offers breakthrough
display technology as well as easy-to-program single-line parameters.
Designed to provide instant visual feedback regarding an application's key input value, the tico 735 not
only has a 18 mm high LED display, but also the ability to change display colour based on process status
(programmable parameter in Operation Mode). Easy programming is made possible via a help function
and a secondary legend display.
This manual will guide you through the installation and wiring of your tico 735 unit with information on
proper panel mounting and rear terminal layout and wiring instructions. In addition, the instrument's
operation and programming modes are thoroughly explained. The operation mode provides day to day
operation and allows editing of preset values. The Program Mode enables the configuration of various
parameters prior to initial operation. These parameters include those for basic configuration as well as
other settable features which will enhance the functionality
and usability of the device.
This manual also provides information on the tico 735
Elapsed Timers's transistor and relay outputs, product
specifications and ordering and warranty information.
Features
• Awesome 18 mm high digit LED display
• Programmable colour change display based on an
event
• Programmable help function and secondary legend display
• Programmable for single input or cumulative operation
• Choice of NPN or PNP primary input
• Standard outputs: one NPN transistor & one relay
• Front panel reset enable and preset lockout
• Optional RS-485 plug in card
Index
Safety Instructions ...........................................................................................................................2
Installation........................................................................................................................................3
Panel mounting .........................................................................................................................3
Wiring........................................................................................................................................4
Operation .........................................................................................................................................5
Front Panel ...............................................................................................................................5
Operation Mode ........................................................................................................................6
Program Mode .................................................................................................................................7
Entering Program Mode and basic operation............................................................................7
Program Parameter Sequence .................................................................................................8
Technical Data...............................................................................................................................11
Ordering Information ...............................................................................................................12
2 735 061, Rev. 030798
Operating Instructions tico 735 - Elapsed Timer
page 1/12
Advertisement
Table of Contents
Related Manuals for Hengstler tico 735
Summary of Contents for Hengstler tico 735
-
Page 1: Table Of Contents
Operating Instructions tico 735 - Elapsed Timer Introduction Your Hengstler tico 735 Elapsed Timer is one model in a family of 1/8 DIN units which offers breakthrough display technology as well as easy-to-program single-line parameters. Designed to provide instant visual feedback regarding an application’s key input value, the tico 735 not only has a 18 mm high LED display, but also the ability to change display colour based on process status (programmable parameter in Operation Mode). -
Page 2: Safety Instructions
When putting into operation, the EMC of the whole installation (unit) has to be secured. In particular, the relay outputs are to be protected from high noise radiation by suitable wiring. 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 2/12... -
Page 3: Installation
To remove the components, grip the side edges of the panel and pull the instrument forward. Take note of orientation of the unit for subsequent replacement in the housing. 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 3/12... -
Page 4: Wiring
AC powered units and the negative side for DC powered units are connected to terminal #14. Terminals 1,9,10,11,12,15,22,23 & 24 are not used and must not be connected! 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 4/12... -
Page 5: Operation
Program Mode. In Program Mode: No function Down & In All Modes: Will abort an Edit Operation Scroll and return the preset/parameter to its previous value. 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 5/12... -
Page 6: Operation Mode
Function : Displays the present which output 1 will be activated time value. Adjustment Range: 0 to 99999 Adjustement Range : Default Value: 0 0 to 99999 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 6/12... -
Page 7: Program Mode
Program Mode the scroll and edit keys to change the value as in Operation Mode, described on page 5. Press the Program Key to enter any changes. 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 7/12... -
Page 8: Program Parameter Sequence
Source: The unit will accept an NPN or dry accept an PNP input contact input which which sources voltage sinks voltage to common Default Value : Sinking 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 8/12... - Page 9 It will being reached. It will turn red after Preset turn green after the Green to red has been reached Preset has been reached 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 9/12...
- Page 10 3 seconds 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 10/12...
-
Page 11: Technical Data
12 (unregulated VDC), 125 mA max; ripple < 0.5 V RS-485 Option 6OFA RS485, serial asynchronous, Open ASCII, Master-Slave, up to 99 zones Parameters 9600...1200 Bd, 1 start, 7 data, 1 stop, even parity 2 735 061, Rev. 030798 Operating Instructions tico 735 - Elapsed Timer page 11/12... -
Page 12: Ordering Information
9 Batch Counter (only with function 2,4,5) © 1998 HENGSTLER GmbH This documentation may not be changed, amended, or copied without prior written consent of HENGSTLER GmbH, and may not be used in contradiction to this company’s rightful interests. Hengstler GmbH...
Need help?
Do you have a question about the tico 735 and is the answer not in the manual?
Questions and answers