Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Riello 7200/1 170 Plus
Summary of Contents for Riello 7200/1 170 Plus
- Page 1 7200/1 170 Plus EN INSTALLER, TEchNIcAL ASSISTANcE SERvIcE AND USER MANUAL...
- Page 2 MODEL CODE dependable and safe service and to provide comfort in the 7200/1 170 Plus 20072892 home for many years to come. Arrange for your solar storage cylinder to be serviced regularly by an authorised...
-
Page 3: Table Of Contents
coNTENTS GENERAL general Safety Information ..... . 4 Precautions ........4 Description of the appliance . -
Page 4: General
gENERAL gENERAL gENERAL SAFETY INFoRMATIoN 2 PREcAUTIoNS The operation of any appliance that uses electrical power demands that a number of fundamental safety precautions be check that the product is complete, undamaged and as respected. In particular: ordered as soon as you receive it. Report any discrepancies or damage to the dealer who sold it. -
Page 5: Description Of The Appliance
4 IDENTIFIcATIoN 7200/1 Plus storage cylinders are identified by: Data plate This lists the technical specifications and performance of the product. RIELLO S.p.A. Via Ing.Pilade Riello 7 37045 Legnago (VR) - ITALY BOLLITORE SOLARE BALLON SOLAIRE SOLAR STORAGE CYLINDER Modello... -
Page 6: Technical Specifications
6 TEchNIcAL SPEcIFIcATIoNS DESCRIPTION 7200/1 170 Plus Type of storage cylinder Vitrified Storage cylinder layout vertical heat exchanger layout vertical Storage cylinder capacity Diameter of storage cylinder with insulation height with insulation 1145 Insulation thickness Diameter/length of first magnesium anode... -
Page 7: Water Circuit
gENERAL gENERAL 7 WATER cIRcUIT TYPICAL WATER SYSTEM SCHEMATIC Solar regulator °C Water control system Solar collector 19 DhW recirculation temperature sensor collector temperature sensor socket Domestic hot water outlet Manual bleed valve Domestic cold water inlet vent cock collector outlet vent valve collector return Pressure gauge... -
Page 8: Location Of Sensors
gENERAL gENERAL 8 LocATIoN oF SENSoRS 7200/1 Plus storage cylinders are equipped with dedicated sockets for the storage cylinder TEMPERATURE gAUgE or TEMPERATURE SENSoR. The installer is responsible for making all necessary connections to the boiler and solar collectors. Installers must use their expertise to ensure proper installation and functioning in compliance with all applicable legislation. -
Page 9: Overall Dimensions And Water Fittings
9 ovERALL DIMENSIoNS AND WATER FITTINgS EAF (SB) (*) hoses DESCRIPTION 7200/1 170 Plus Domestic hot water outlet 1” F Ø outlet from solar collector 1” M Ø Return to solar collector 1” M Ø DhW recirculation 3/4” F Ø... -
Page 10: Installer
− carefully rotate and slide the storage cylinder off the platform on to the floor − Remove the platform. Position the storage cylinder as required. 7200/1 170 Plus 1300 Adjust the feet to ensure that the storage cylinder is perfectly level. -
Page 11: Place Of Installation
TEchNIcAL ASSISTANcE SERvIcE TEchNIcAL ASSISTANcE SERvIcE 12 PLAcE oF INSTALLATIoN 14 PUTTINg INTo SERvIcE 7200/1 Plus storage cylinders can be installed in any It is essential to perform the following checks before starting up room where there is no specific requirement for an electrical or testing the functioning of the storage cylinder. -
Page 12: Temporary Shutdown
TEchNIcAL ASSISTANcE SERvIcE TEchNIcAL ASSISTANcE SERvIcE 15 TEMPoRARY ShUTDoWN 18 cLEANINg AND REMovINg INTERNAL coMPoNENTS If you are going away for a short period of time like a weekend EXTERNAL CLEANING or a short holiday, etc., and outdoor temperatures are going to clean the outside of the storage cylinder with a soft cloth damped remain above ZERo, proceed as follows. -
Page 13: Troubleshooting
TEchNIcAL ASSISTANcE SERvIcE TEchNIcAL ASSISTANcE SERvIcE 19 REcYcLINg AND DISPoSAL Tighten the bolts (7), proceeding diagonally around the flange to apply pressure uniformly around the seal. At the end of its useful working life, do not abandon the storage cylinder in the environment, but dispose of it through the proper −... -
Page 14: End User
END USER END USER End usEr instructions Refer to the GENERAL SAFETY INFORMATION and PRECAUTIONS section for safety-related information. 21 START-UP 22 TEMPoRARY ShUTDoWN The storage cylinder must be put into service for the first time by To reduce impact on the environment and save energy, before personnel from the manufacturer’s Technical Assistance Service. - Page 15 END USER END USER...
- Page 16 RIELLo S.p.A. 37045 Legnago (vR) - Italy Tel. 0442630111 - Fax 044222378 - www.riello.it The manufacturer strives to continuously improve all products. Appearance, dimensions, technical specifications, standard equipment and accessories are therefore liable to modification without notice.