CYP CDPS-RLY Operation Manual

Auxiliary relay control system

Advertisement

Quick Links

CDPS-RLY
Auxiliary Relay Control System
Operation Manual
Operation Manual

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the CDPS-RLY and is the answer not in the manual?

Questions and answers

Summary of Contents for CYP CDPS-RLY

  • Page 1 CDPS-RLY Auxiliary Relay Control System Operation Manual Operation Manual...
  • Page 2 DISCLAIMERS The information in this manual has been carefully checked and is believed to be accurate. Cypress Technology assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use. Cypress Technology assumes no responsibility for any inaccuracies that may be contained in this document.
  • Page 3: Safety Precautions

    SAFETY PRECAUTIONS Please read all instructions before attempting to unpack, install or operate this equipment and before connecting the power supply. Please keep the following in mind as you unpack and install this equipment: • Always follow basic safety precautions to reduce the risk of fire, electrical shock and injury to persons.
  • Page 4: Table Of Contents

    CONTENTS 1. Introduction ..........1 2. Applications ........... 1 3. Package Contents ........ 1 4. System Requirements ......1 5. Features ..........2 6. Operation Controls and Functions ..3 6.1 Front Panel ........3 6.2 Rear Panel .........4 6.3 Top Panel ..........4 6.4 RS-232 Protocol .........5 6.5 RS-232 and Telnet Commands ..5 7.
  • Page 5: Introduction

    1. INTRODUCTION The Auxiliary Relay Control System is design for multi-purpose and multi-task trigger system usage. With 8 relays to trigger, 8 PWM (Pulse- Width Modulation) to set duty cycle, 8 voltage to set trigger voltage and 1 definition to control through command setting which supports RS-232/422/485 and DM512 that allows up to 25 devices connection for control.
  • Page 6: Features

    5. FEATURES • Supports 8 Relays, 8 PWM, 8 Voltage and 1 Definition outputs • Reply supports close, open and toggle controls with LED illuminators and power up to 30V/DC, 10A • PWM support 10 volt with 0~100% duty cycle adjustable •...
  • Page 7: Operation Controls And Functions

    6. OPERATION CONTROLS AND FUNCTIONS 6.1 Front Panel POWER DC 5~24V: The device support power supply from 5~24V/2.6~1.25A, plug the 24V DC power supply from the included package into the unit and connect the adaptor to an AC outlet. CONTROL: This slot is to connect with active LAN system for IP control.
  • Page 8: Rear Panel

    6.2 Rear Panel RELAY CONTROL OUTPUT 1~8: These slots are to connect with control device’s power ± line cable such as A/C sensor, IR sensor or curtain sensor for control signal sending to activate the control devices. Trigger events can be set with 3 control type of Close, Open and Toggle through command settings.
  • Page 9: Rs-232 Protocol

    6.4 RS-232 Protocol DATA TERMINAL EQUIPMENT Assignment 6.5 RS-232 and Telnet Commands COMMAND DESCRIPTION PARAMETER IPCONFIG Display the current IP NONE configure SIPADDR XXX. Set Ethernet IP address XXX=0~255 XXX.XXX.XXX SNETMASK XXX. Set Ethernet net mask XXX=0~255 XXX.XXX.XXX SGATEWAY XXX. Set Ethernet gateway XXX=0~255 XXX.XXX.XXX...
  • Page 10 COMMAND DESCRIPTION PARAMETER Write MAC address to CYP WRITE MAC ADDRESS eeprom TO EEPROM, XX-XX-XX-XX- XX-XX RELAY N1 N2 Relay control N1=1~8 (Port Number), N2=OPEN/CLOSE/TOGGLE PWM N1 N2 PWM duty cycle control N1=1~8 (Port Number), N2=0~100 (Duty Cycle) DAC N1 N2...
  • Page 11: Connection Diagram

    7. CONNECTION DIAGRAM Blind Lighting Control Control Control Relay Control Outputs RELAY CONTROL OUTPUT RELAY STATUS POWER OUT DEF. DMX512 (10 V) (0~10 V) RS485 DC 5~24V PWM OUT VOLTAGE OUT RS422 RX+ RX- RS232 TXD GND 1 2 3 4 5 6 7 8 1 2 3 4 5 6 7 8 CONTROL SERVICE...
  • Page 12: Specifications

    8. SPECIFICATIONS Input Ports 1×IP Control (RJ45), 1×RS-232 (9-pin D-sub) Output Ports 8×Relay (Terminal Block), 8×Vpltage (Terminal Block), 8×PWM (Terminal Block), 1×RS-232/RS-422/RS-485/DMX512 (Terminal Block) Baud Rate Up to 115200 bps Power Supply 5 V/2.6 A DC (US/EU standards, CE/FCC/UL certified) ESD Protection Human body model: ±8 kV (air-gap discharge)
  • Page 13: Acronyms

    9. ACRONYMS ACRONYM COMPLETE TERM Internet Protocol Powered Device Power over Ethernet Pulse-Width Modulation Universal Serial Bus...
  • Page 14 CYPRESS TECHNOLOGY CO., LTD Home page: http://www.cypress.com.tw...

Table of Contents